Gebruiksaanwijzing /service van het product AP3000 van de fabrikant Asus
Ga naar pagina of 42
AP3000 Dual Pentium ® II Server Platform Hardware Reference Guide.
2 AP 3000 Hardwar e Reference Guide Product Name: AP3000 Manual Revision: 1.00 E321 Release Date: February 1999 No part of this manual, including the products and software described in it, may be repr.
AP 3000 Hardware Refer ence Guide 3 ASUS Contact Information ASUST eK COMPUTER INC. (Asia-Pacific) Marketing Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 112 T elephone: +886-2-2894-3447 Fax: +886-2-2894-3449 Email: info@asus.com.tw T echnical Support T el (English): +886-2-2894-3447 ext.
4 AP 3000 Hardwar e Reference Guide I. Introduction 1-1. How this Manual is Organized ........................................... 7 Symbols ............................................................................. 7 1-2. Component Checklist ......
AP 3000 Hardware Refer ence Guide 5 Floppy Drive and CD-ROM .............................................. 26 Fixed Storage Device T ray ............................................... 26 Fixed Device Bay Cover Clips ..................................
6 AP 3000 Hardwar e Reference Guide FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditio.
AP 3000 Hardware Refer ence Guide 7 I. Introduction I. Introduction I. Introduction Y ou are reading the AP3000 Hardware Reference Guide. This hardware refer - ence guide provides information and procedures on the various components used in this server .
8 AP 3000 Hardwar e Reference Guide I. Introduction I. Introduction I. Introduction AP 3000 Hardwar e Reference Guide Checklist • 1-2. Component Checklist If assembling this server by yourself, it is important to prepare all the server components before starting.
AP 3000 Hardware Refer ence Guide 9 I. Introduction I. Introduction 9 I. Introduction Features AP 3000 Hardware Refer ence Guide • 1-3. Features AP3000 is a department server configured on the XG-DL.
10 AP 3000 Hardwar e Reference Guide I. Introduction I. Introduction • 1-4. Safeguards Observe the following safety instructions any time you are connect- ing or disconnecting any devices. Operation Safety • Any operation on this server must be conducted by cer - tified or experienced engineers.
AP 3000 Hardware Refer ence Guide 11 I. Introduction I. Introduction I. Introduction Electrical Safety • 1-5. Electrical Safety IMPOR T ANT • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged.
12 AP 3000 Hardware Reference Guide (This page was intentionally left blank).
AP 3000 Hardware Refer ence Guide 13 II. System Components II. Components 1. T op Panel 2. Power LED 3. A TX Power Button 4. Hard Drive Access LED 5. Floppy Disk Drive 6. CD-ROM Drive 7. Drive Expansion Bay 8. Side Panel Handle 9. Side Panel Screw 10.
14 AP 3000 Hardwar e Reference Guide II. System Components II. Components 1. T op Panel Screw 2. Power Supply 3. Power Supply Fan 4. AC Power In Connector 5. PS/2 Keyboard, PS/2 Mouse 6. USB Ports 1 and 2 7. Serial Port COM1 8. Parallel Port 9. Serial Port COM2 10.
AP 3000 Hardware Refer ence Guide 15 II. System Components II. Components Back Side Back Side II. Components Server Left Side 1. Power Supply 2. Motherboard 3. Chassis Intrusion Switch 4. Chassis Stabilizer (shown recessed) 5. Expansion Card Guide 6. Rear Fans Left Side • 2-3.
• 3-1. Starting the Server T urn O N the server b y pushing the power button. The power button will snap back when released because A TX power systems have an electrical ON /OF F switch unlike A T systems which require a permanent ON or OF F position.
17 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Panel Screws The top panel on the chassis is secured by two screws on the back of the server . T o open the top panel, remove the screws with a screw driver . NOTE: Y ou do not have to open the top panel before removing the left panel.
18 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide Opening the Left Panel There are two identical side panels on the chassis, one on each side. T o open the left side of the panel (see the left view), remove the side panel screw , then pull the handle outward while pulling the panel forward.
19 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide • 4-2. Rear Cooling Fan Control Board Rear Cooling Fan Control Board Settings The rear fan control board has DIP switches to allow controlling the control board status and the number of fans.
20 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide Spacer Install the Baseboard A metal baseboard is required to add stability to the motherboard. A rub- ber pad is placed between the metal board and motherboard to provide insulation to prevent shorting.
21 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Motherboard Device Cables Several cables are used for connecting devices in this chassis. The following picture points out the name of each cable and its suggested location. Plastic keepers protect the cables from contacting with the fans and other devices.
22 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide CPU Install Retention Mechanism Brace Bars Place the retention mecha- nism brace bar into the groove on the top of the retention mechanism as shown. Retention Mechanism Brace Bar Long Screw (aligned with spacers) Captive Nut Short Screw • 4-4.
23 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Install Retention Mechanism Frame A metal frame is used accross both retention mechanisms. After install- ing the frame, four captive nuts should be tightened on the feet of the frame to the screws pro- truding from the reten- tion mechanisms.
24 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide • 4-5. Chassis Intrusion Switch IMPOR T ANT Chassis Intrusion Switches (one on each side) Cable The chassis provides a micro toggle switch that must be connected to the motherboard for the chassis intrusion detection to work.
25 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Expansion cards can be easily installed just like on any stan- dard PC. Up to 5 PCI or 1 ISA cards can be installed. One AGP slot is also available for an AGP graphics adapter to provide hardware 3D acceleration and free up an extra PCI slot.
26 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide • 4-7. Fixed Storage Devices Internal fixed storage devices are mounted on removable trays. There are four available, one for a floppy device and another three for full- size devices.
27 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Fixed Device Bay Cover After releasing the device bay cover clips, pry the cover away from the chassis using a screw driver from the front. Fixed Device Bay Cover Clips The device bay panel is held by two plastic clips on each side.
28 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide • 4-8. Five-T ray Hot-Swap Bay • 4-9. Three-T ray Hot-Swap Bay LEDs LEDs Green: Power LED Y ellow: Hard Disk Access LED Red: Hard Disk Status LED (reserved) (For details about LEDs, see p.
29 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Hot-Swap Bay Hot-Swap Bay T o remove the hot-swap bay , release the front cooling fans first by pressing the eject mechanism with a small screwdriver . Remove the six retaining screws as circled above and then the entire hot-swap bay can be slid out of the chassis.
30 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide • 4-10. Front Cooling Fans The front cooling fan module consists of a control board, a hard disk drive LED status board, and two cooling fans.
31 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide Front Cooling Fan Control Board A cable connects the front cooling fan control board and the hard disk drive message board. Orient the red markings on each end of the cable to pin 1.
32 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide The SCSI backplane of this server is comprised of one SCSI board (DA- BP5) with Ultra2 SCSI connectors, power inputs, and SCSI ID dip switches. This configuration allows Ultra2 SCSI SCA hard disk drives to be docked into the server .
33 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide IDSEL 1=of f IDSEL 0=of f ON IDSEL 1=on IDSEL 0=on ON IDSEL 1=on IDSEL 1=of f ON ON IDSEL 1=of f IDSEL 0=on ON IDSEL1 IDSEL0 Slot1 Slot2 Slot3A Slot4 Slot5A off off Resv .
34 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide IDSEL 1=of f IDSEL 0=of f ON IDSEL 1=on IDSEL 0=on ON IDSEL 1=on IDSEL 1=of f ON ON IDSEL 1=of f IDSEL 0=on ON IDSEL1 IDSEL0 Slot1 Slot3B Slot5B off off Resv .
35 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide • 4-14. SCSI T ermination Female T erminator for SCSI cable Male T erminator for SCSI Board • 4-15. Power Supply Power Supply Mounting Mounting and unmounting the power supply must be done from the inside.
36 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardwar e Reference Guide Output V oltage Regulation, Ripple, and Noise Output Current Capacity Input V oltage Safety The power system meets all applicable clauses for UL 1950 2nd edition with- out D3 deviations.
37 IV . Hardware Setup IV . Hardware Setup AP 3000 Hardware Refer ence Guide • 4-16. Power Supply Requirement Power Supply Requirement Calculation T able Item V olts Amp x Qty . = T otal Amp W atts (5V) W atts (12V) 209.55 3.6 Hard Drive 5.0V 1.3 x = 12V 1.
38 AP 3000 Hardwar e Reference Guide (This page was intentionally left blank).
AP3000 Hardware Refer ence Guide 39 V . Appendix V . Appendix i. SCSI Cable Limits SCSI cables have a limit to the length that it may have. Exceeding the length may cause problems mounting or using any one of the SCSI devices. Cable Limits Max Data T ransfer Rates Max Devices 1) 12m (29.
40 AP3000 Hardware Refer ence Guide V . Appendix V . Appendix ii. Glossary Byte (Binary T erm) One byte is a group of eight contiguous bits. A byte is used to represent a single alphanumeric character , punctuation mark, or other symbol.
AP3000 Hardware Refer ence Guide 41 V . Appendix V . Appendix Glossary Peripherals Peripherals are components on the outside of the computer such as a moni- tor , printer , keyboard, or mouse. Peripherals are attached to the computer via I/O ports. Peripheral devices allow your computer to perform an almost limitless variety of specialized tasks.
(This page was intentionally left blank.) 42 AP3000 Hardware Refer ence Guide.
Een belangrijk punt na aankoop van elk apparaat Asus AP3000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Asus AP3000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Asus AP3000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Asus AP3000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Asus AP3000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Asus AP3000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Asus AP3000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Asus AP3000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
