Gebruiksaanwijzing /service van het product TX-SR805 van de fabrikant Onkyo
Ga naar pagina of 120
E n AV Receiv er TX-SR8 0 5 TX-SR8 7 5 Instruction Manual Thank you for purchasing an Onkyo A V Receiv er . Please read this manual thoroughly before making connections and plugging in the unit. F ollo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiver .
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The AC fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact your Onkyo dealer .
4 Precautions —Continued F or British models Replacement and mounting of an AC plug on the po wer supply cord of this unit should be performed only by qualified service personnel.
5 Contents Features ............................................................ 6 Supplied Accessories ...................................... 7 Multiroom Capability ........................................ 8 Getting to Know the AV Receiver ..........
6 Features Amplifier • 7-channel amplifier • 130 watts minimum continuous po wer per channel, 8 ohm loads, 2 channels driv en from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
7 Features —Continued *5 Theater-Dimensional is a trademark of Onk yo Corporation. *6 Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd. *7 HDMI, the HDMI logo and High Definition Multimedia Inter - f ace are trademarks or registered trademarks of HDMI Licens- ing, LLC.
8 Multir oom Capability Y ou can use three speaker systems with this A V receiv er —a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it, and another stereo speaker system in a third room that we call Zone 3 (external po wer amplifier required).
9 Getting to Kno w the A V Receiver The actual front panel has various logos printed on it. They are not sho wn here for clarity . For detailed information, see the pages in parentheses. A ST ANDBY/ON b utton (44) Sets the A V receiver to On or Standby .
10 Getting to Know the A V Receiver —Continued For detailed information, see the pages in parentheses. M PHONES jack (69) This 1/4-inch phone jack is for connecting a stan- dard pair of stereo headphones for priv ate listening. N ZONE 2, ZONE 3, and OFF buttons (105) The ZONE 2 button is used when setting Zone 2.
11 Getting to Know the A V Receiver —Continued c DIGIT AL INPUT b utton (53) Used to assign digital inputs to input selectors. d LISTENING MODE [ ]/[ ] b uttons (71) Select the Onkyo original listening modes. e PO WER switch (44) American models do not hav e this switch.
12 Getting to Know the A V Receiver —Continued A REMO TE CONTROL This (Remote Interactiv e) jack can be con- nected to the jack on another -capable Onkyo component for remote and system control. To use , you must make an analog audio connec- tion (RCA) between the A V receiver and the other component, ev en if they are connected digitally .
13 Getting to Know the A V Receiver —Continued M IR IN/OUT A commercially av ailable IR recei ver can be con- nected to the IR IN jack, allowing you to control the AV receiver while you’ re in Zone 2, or control it when it’ s out of sight, for example, installed in a cabinet.
14 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or dif ferent types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
15 Remote Controller —Continued As well as the A V receiver, you can also use the remote controller to control your other A V components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the REMO TE MODE buttons.
16 Remote Controller —Continued For detailed information, see the pages in parentheses. A ST ANDBY b utton (44) Sets the A V receiver to Standby . B ON button (44) T urns on the A V receiv er. C INPUT SELECT OR buttons (62) Used to select the input source.
17 Remote Controller —Continued To set the r emote controller to D VD mode, press the [D VD] REMO TE MODE button. A ST ANDBY b utton Sets the D VD player to Standby . B ON button T urns on the D VD player . C Number buttons Used to enter title, chapter , and track numbers, and to enter times for locating specific points.
18 Remote Controller —Continued To control an Onk yo CD player , MD recorder , or CD recorder , or a CD or MD player/recorder made by another manufacturer , press the [CD] REMO TE MODE button to select the CD/MD/CDR r emote con- troller mode.
19 Remote Controller —Continued Dock mode is for controlling an Apple iPod in an Onkyo RI Dock that’ s connected via . When Using an RI Dock: • Connect the RI Dock to the T APE IN or GAME/TV IN L/R jacks. • Set the RI Dock’ s RI MODE switch to HDD.
20 Connecting Y our Speaker s Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring Dolby Digital or DTS.
21 Connecting Y our Speakers —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve.
22 Connecting Y our Speakers —Continued Speaker Connection Precautions Read the following before connecting your speak ers: •Y ou can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more b ut less than 6, be sure to set the speaker impedance to 4 ohms (see page 45).
23 Connecting Y our Speakers —Continued The FR ONT L/R and SURR B A CK L/R terminal posts can be used with front speakers and surround back speakers respecti vely , or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing impro ved bass and treble performance.
24 Connecting Y our Speakers —Continued The FR ONT L/R and SURR B A CK L/R terminal posts can be used with front speakers and surround back speakers respecti vely , or bridged together to provide almost double the output power for the front speak ers.
25 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up an y radio signals without any antenna connected, so you must connect the antenna to use the tuner .
26 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
27 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
28 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver.
29 Connecting Y our Components —Continued ■ HDMI Monitor Setting Set to No W ith the HDMI Monitor setting set to No (see page 46), video input signals flow through the AV receiver as sho wn, with composite video and S-V ideo sources being upconv erted for the component video output.
30 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .
31 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a D VD or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .
32 Connecting Y our Components —Continued Hooking Up the Multichannel Input If your D VD player supports multichannel audio formats such as D VD-Audio and SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel input.
33 Connecting Y our Components —Continued W ith this hookup, you can use the tuner in your VCR or DVR to listen to your fa vorite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •W ith connection , you can listen to the VCR or D VR in Zone 2 or Zone 3.
34 Connecting Y our Components —Continued Notes: • The A V receiv er must be turned on for recording. Recording is not possible while it’ s on Standby .
35 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fa vorite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •W ith connection , you can listen to and record audio from the video source or listen in Zone 2 or Zone 3.
36 Connecting Y our Components —Continued About HDMI Designed to meet the increased demands of digital TV , HDMI (High Definition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, D VD players, set-top boxes, and other video components.
37 Connecting Y our Components —Continued Making HDMI Connections ■ Video Signals Digital video signals receiv ed by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV . Composite video, S-V ideo, and component video sources can be upconv erted for the HDMI output.
38 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your game console or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection . (T o record or listen in Zone 2 or Zone 3 as well, use and .
39 Connecting Y our Components —Continued Connecting a Camcorder or Other A V Component Connection A V receiver Signal flow Camcorder A UX 2 INPUT S VIDEO ⇐ S-Video output A UX 2 INPUT VIDEO ⇐ .
40 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the CD player or listen in Zone 2 or Zone 3. •T o connect the CD player digitally , use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .
41 Connecting Y our Components —Continued •W ith connection , you can play and record or listen in Zone 2 or Zone 3. •T o connect the recorder digitally for playback, use connections and , or and . •T o connect the recorder digitally for recording, use connection .
42 Connecting Y our Components —Continued ■ If Y our iPod Supports Video: Connect your RI Dock’ s audio output jacks to the AV receiver’ s GAME/TV IN L/R jacks, and connect its video output jack to the A V receiver’ s GAME/TV IN V jack. (Onkyo DS-A2 hookup sho wn below .
43 Connecting Y our Components —Continued W ith (Remote Interactiv e), you can use the following special functions: Auto P ower On/Standby When you start playback on a component connected via , if the A V receiver is on Standby , it will automatically turn on and select that component as the input source.
44 T urning On the A V Receiver For non-North American models: To completely shut down the A V receiver, set the [PO WER] switch to the OFF position ( ).
45 Fir st Time Setup This section explains the settings that you need to make before using the A V recei ver for the very first time. If the impedance of any speaker is 4 ohms or more b ut less than 6, set the Speaker Impedance to 4 ohms.
46 First Time Setup —Continued If you connect your TV to the COMPONENT VIDEO OUT , set the HDMI Monitor setting to No so that the onscreen setup menus are displayed and composite video and S-V ideo sources are upconv erted and output by the COMPONENT VIDEO OUT .
47 First Time Setup —Continued Notes: • See page 29 for charts showing ho w the HDMI Moni- tor and Resolution settings affect the video signal flo w through the A V receiver. • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons.
48 First Time Setup —Continued If you connect a video component to an HDMI IN, you must assign that input to an input selector . For example, if you connect your D VD player to HDMI IN 1, you must assign HDMI IN 1 to the D VD input selector . By default, none of the HDMI inputs are assigned.
49 First Time Setup —Continued • When an HDMI IN is assigned to an input selector as explained here, the digital audio input for that input selector is automatically set to the same HDMI IN. See “Digital Input Setup” on page 52. • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons.
50 First Time Setup —Continued If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector . For example, if you connect your D VD player to COMPONENT VIDEO IN 3, you must assign COM- PONENT VIDEO IN 3 to the DVD input selector .
51 First Time Setup —Continued Notes: •F or composite video and S-V ideo upcon version for the COMPONENT VIDEO OUT , the HDMI Monitor set- ting must be set to No (see page 46). See page 28 for more information on video signal flow and upcon ver- sion.
52 First Time Setup —Continued If you connect a component to a digital audio input, you must assign that input to an input selector . For example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the CD input selector .
53 First Time Setup —Continued Notes: • Only FR ONT can be assigned to the A UX 2 input selector . • The TUNER input selector cannot be assigned and is fixed at the “- - -” option. • When an HDMI IN is assigned to an input selector in “HDMI V ideo Setup” on page 48, this input assign- ment is automatically set to the same HDMI IN.
54 First Time Setup —Continued If you connect a component to the A V receiver’ s analog multichannel input, you must assign that input to an input selector . For example, if you connect your D VD player to the MUL TI CH input, you must assign it to the D VD input selector .
55 First Time Setup —Continued W ith the supplied speaker setup microphone, Audyssey MultEQ XT can measure the number of speakers con- nected, their sizes, crossov er frequencies, and distances from the listening position and calculate the optimal speaker settings for you automatically .
56 First Time Setup —Continued 1 T urn on the A V receiver and the connected TV . On the TV , select the input to which the AV receiver is connected. 2 Place the setup microphone at the 1st measurement position, and connect it to the SETUP MIC jack.
57 First Time Setup —Continued Notes: • When the automatic speaker setup is complete, the Equalizer Settings (page 91) will be set to Audyssey . •Y ou can cancel the automatic speaker setup at any point in the procedure simply by disconnecting the setup microphone.
58 First Time Setup —Continued Speaker Detect Error This message appears if a speaker is not detected. “Y es” means that a speaker was detected. “No” means that no speaker was detected. Check your speak er connections and retry , or cancel the automatic speaker setup.
59 First Time Setup —Continued Revie wing the Results Changing the Speaker Settings Manuall y In some cases, the measurements taken by the automatic speaker setup may not provide usable results. If running the speaker setup a second time doesn’ t help, you’ll hav e to set the speaker settings manually (see pages 86–91).
60 First Time Setup —Continued For the onscreen setup menus to display properly , you must specify the TV system used in your area. Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons.
61 First Time Setup —Continued For AM tuning to work properly , you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons.
62 Pla ying Y our A V Components Basic A V Receiver Operation STANDBY/ON MASTER VOLUME CD TUNER TAPE CBL/SAT GAME/TV AUX 1 AUX 2 VCR/DVR DVD AUDIO SEL PURE AUDIO PHONO DISPLAY PUSH TO OPEN STANDBY REA.
63 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears.
64 Listening to the Radio —Continued ■ T uning into Stations b y Frequency Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Displaying AM/FM Radio Inf ormation Note: • When you select a preset with a custom name (see page 94), its name is displayed instead of the band and frequency .
65 Listening to the Radio —Continued RDS only works in areas where RDS broadcasts are av ailable. When tuned to an RDS station, the RDS indi- cator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals.
66 Listening to the Radio —Continued Displaying Radio T ext (R T) When tuned to an RDS station that’ s broadcasting text information, the text can be displayed. Notes: • The message “W aiting” may appear while the A V receiv er waits for the R T information.
67 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM and FM radio stations. Note: •Y ou can name your radio presets for easy identifica- tion (see page 94). Selecting Presets Deleting Presets Presetting AM/FM Stations 1 T une into the AM or FM station you want to store as a preset.
68 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the volume of each speaker while listen- ing to an input source. These temporary adjustments are cancelled when the A V receiver is set to Standby .
69 Common Functions —Continued W ith the sleep timer , you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] b utton.
70 Common Functions —Continued If you connect a component to more than one audio input, such as a D VD player connected to analog, digital, multichannel, and HDMI inputs, you can use the [A UDIO SEL] button to select which audio input you want to use to listen to that component.
71 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 76. Selecting on the A V Receiver ■ [PURE A UDIO] button This button selects the Pure Audio listening mode. When this mode is selected, the A V receiver’ s dis- play is turned off and only the HDMI OUT outputs video signals.
72 Using the Listening Modes —Continued Analog and PCM Sources Listening Modes A v ailable f or Each Source Format Button Source f ormat PCM Multi channel analog Multichannel PCM 32–96 kHz 176.4/ 192kHz* 1 32–96 kHz 176.4/192 kHz *1 *1. DVD-Audio discs output multichannel 176.
73 Using the Listening Modes —Continued DSD , Dolby Digital, and Dolby Digital Plus Sour ces Button Source f ormat DSD *1 *1. In listening modes other than DSD Direct, DSD sources are converted and handled as PCM.
74 Using the Listening Modes —Continued T rueHD and DTS Sour ces Button Source f ormat T rueHD *1 *1. For 96 kHz TrueHD sources, only the Tone audio adjust function is available.
75 Using the Listening Modes —Continued DTS-HD Sources Button Source f ormat DTS-HD High Resolution DTS-HD Master Audio *1 *1. For 96 kHz DTS-HD Master Audio sources, only the Tone audio adjust function is available. 192 kHz DTS-HD Master Audio sources are processed at 96 kHz.
76 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
77 Using the Listening Modes —Continued DTS-ES Discrete This mode is for use with DTS-ES Discrete soundtracks that use a discrete surround-back channel for true 6.
78 Using the Listening Modes —Continued Onkyo Original DSP Modes Mono Movie This mode is suitable for old movies and other mono sources. The center speak er outputs the sound as it is, while rev erb is applied to the sound output by the other speakers, gi ving presence to ev en mono material.
79 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded.
80 Onscreen Setup Menus The onscreen setup menus appear on the connected TV and pro vide a con ve- nient way to change the A V receiv er’ s various settings. Settings are organized into eight categories on the main menu , most containing a submenu .
81 Adjusting the Listening Modes W ith the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing.
82 Adjusting the Listening Modes —Continued W ith the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. T one Contr ol Settings Y ou can adjust the tone (bass and treble) of the front, center , surround, and surround back speakers indi vidu- ally .
83 Adjusting the Listening Modes —Continued Direct Setting Delay Enable ■ DSD This setting determines whether or not DSD (SA CD) audio signals are passed through the DSP for A/V Sync, delay , etc., processing when the Pure Audio or Direct lis- tening mode is selected.
84 Adjusting the Listening Modes —Continued Dolby Digital Settings ■ Dolby EX This setting determines how Dolby EX signals are han- dled. If you’ re not using any surround back speakers, or Powered Zone 2 is being used (page 101), this setting is unav ailable.
85 Adjusting the Listening Modes —Continued Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons. 3 Use the Up and Down [ ]/[ ] buttons to select an input selec- tor , and then press [ENTER].
86 Ad v anced Setup This section explains items on the Speaker Config menu. Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 55).
87 Adv anced Setup —Continued 5 Use the Up and Down [ ]/[ ] buttons to select “Front, ” and then use the Left and Right [ ]/[ ] b uttons to select a crosso ver frequency .
88 Adv anced Setup —Continued Low-P ass Filter for the LFE Channel W ith this setting, you can specify the cutoff frequenc y of the LFE channel’ s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
89 Adv anced Setup —Continued Speaker Distance W ith the Speaker Distance settings, you can specify the distance from each speaker to the listening position. Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons.
90 Adv anced Setup —Continued Speaker Level Calibration W ith the Lev el Calibration settings, you can adjust the lev el of each speaker while listening to the test tone so that the volume of each speak er is the same at the listen- ing position.
91 Adv anced Setup —Continued Equalizer Settings W ith the Equalizer settings, you can adjust the tone of speakers indi vidually with a 7-band equalizer . The vol- ume of each speaker can be set on page 90. 1 Press the [RECEIVER] REMO TE MODE button, followed b y the [SETUP] button.
92 Adv anced Setup —Continued Notes: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons. • The Equalizer settings hav e no effect on 176.4/ 192 kHz input signals. THX A udio Setup W ith the Surr Back Sp Spacing setting, you can specify the distance between your surround back speakers.
93 Adv anced Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons. This section explains items on the Source Setup menu. Items can be set individually for each input selector .
94 Adv anced Setup —Continued IntelliV olume W ith IntelliV olume, you can set the input level for each input selector individually . This is useful if one of your source components is louder or quieter than the others.
95 Adv anced Setup —Continued Notes: •T o store a name, you must select “OK” and press [ENTER] in step 7, otherwise it will not be sav ed. •Y ou cannot enter a custom name for XM or SIRIUS radio presets. • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons.
96 Adv anced Setup —Continued This section explains items on the Miscellaneous menu. Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons. V olume Setup ■ V olume Displa y W ith this setting, you can choose how the v olume le vel is displayed.
97 Adv anced Setup —Continued ■ Po wer On V olume This setting determines what the volume will be each time the A V receiver is turned on. When the V olume Display preference is set to Absolute, the range is Last, Min, 1 to Max. When it’ s set to Rela- tiv e, the range is Last, – ∞ dB, –81 dB to +18 dB.
98 Adv anced Setup —Continued This section explains items on the Hardware menu. Note: • This procedure can also be performed on the A V receiv er by using its [SETUP], [ENTER], and arrow buttons. Remote Control ■ Remote ID When sev eral Onkyo components are used in the same room, their remote ID codes may ov erlap.
99 Adv anced Setup —Continued T uner ■ AM Freq Step (on some models) See “ AM Frequency Step Setup (on some models)” on page 61. ■ Satellite Radio (on North American model) If you connect an.
100 Adv anced Setup —Continued • HDMI power control only w orks with HDMI-compat- ible components that support it and may not work properly with some components due to their settings or compatibility . • When set to Enable, the A V receiver consumes more power .
101 Zone 2 and Zone 3 In addition to your main listening room, you can also enjoy playback in two other rooms, or as we call them, Zone 2 and Zone 3. And, you can select a different source for each room. There are two ways you can connect Zone 2 speak ers: 1.
102 Zone 2 and Zone 3 —Continued Zone 2 Video Output (TX-SR875 onl y) The TX-SR875 features a composite video output for connection to a TV in Zone 2, so you can enjo y both audio and video in that zone. Hookup • Use a composite video cable to connect the A V receiv er’ s ZONE 2 OUT V jack to a composite video input on your Zone 2 TV .
103 Zone 2 and Zone 3 —Continued If you’ ve connected your Zone 2 speakers to the A V receiv er, as explained in “Connecting Y our Zone 2 Speakers Directly to the A V receiver” on page 101, you must set the Powered Zone 2 setting to Act (Activ ated).
104 Zone 2 and Zone 3 —Continued If you’ ve connected your Zone 2 or Zone 3 speakers to an amp with no volume control, set the Zone 2 Out or Zone 3 Out setting, respectiv ely , to V ariable so that you can set the zone’ s volume, balance, and tone on the A V receiv er.
105 Zone 2 and Zone 3 —Continued Selecting an Input Source f or Zones Notes: •T o select AM or FM, press the [TUNER] input selec- tor button repeatedly . On the North American model, you can also select XM or SIRIUS. • Only analog input sources are output by Zone 2 and Zone 3.
106 Zone 2 and Zone 3 —Continued Adjusting the V olume of Zones Adjusting the Balance of Zones Muting Zones Adjusting the T one of Zone 2 Notes: • Zones can also be unmuted by adjusting the volume.
107 Zone 2 and Zone 3 —Continued To control the A V receiv er with the remote controller while you’ re in Zone 2 or Zone 3, you’ll need a commer- cially av ailable multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech.
108 Contr olling Other Components Y ou can control your other components, including those made by other manufacturers, with the remote controller . This section explains ho w to: • Enter the remote control code for a component that you want to control: D VD, TV , VCR, etc.
109 Controlling Other Components —Continued Remote Control Codes f or Onky o Components Connected via Onkyo components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example.
110 Controlling Other Components —Continued To control another component, point the remote controller at it and use the buttons explained belo w . (Y ou must select the appropriate remote controller mode with the REMO TE MODE buttons first.) W ith some components, certain b uttons may not work as expected, and some may not w ork at all.
111 Controlling Other Components —Continued The A V receiver’ s remote controller can learn the com- mands of other remote controllers. By transmitting, for example, the Play command from your CD .
112 Controlling Other Components —Continued Y ou can program the remote controller’ s MA CR O but- tons to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the follow- ing actions: 1. Press the [RECEIVER] REMO TE MODE button to select the Receiv er remote controller mode.
113 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’t resolv e the issue yourself, contact your Onkyo dealer . Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly .
114 Tr oubleshooting —Continued • While Powered Zone 2 is being used, playback in the main room is reduced to 5.1-channels and the sur- round back speakers produce no sound (page 101). The subwoof er produces no sound • If the source material contains no audio in the LFE channel, the subwoofer produces no sound.
115 Tr oubleshooting —Continued • If the message “Resolution Error” appears on the A V receiv er’ s display , this indicates that your TV does not support the current video resolution and you need to select another resolution on your D VD player .
116 Tr oubleshooting —Continued The A V receiver contains a microcomputer f or signal pro- cessing and control functions. In very rare situations, sev ere interf erence, noise from an e xternal source, or static electricity may cause it to loc kup.
117 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Input ■ Video Output ■ A udio Inputs Rated Output Power TX-SR805: North American: 130 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven fr om 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
118 Specifications —Continued ■ A udio Outputs ■ Control T erminal Specifications and features are subject to change without notice. Digital Output OPTICAL (OUT) Analog Outputs T APE, VCR/D VR.
Memo TX-SR805_875_En.book Page 119 Thursday, April 26, 2007 3:00 PM.
120 SN 29344449B Printed in Japan I0705-3 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.
Een belangrijk punt na aankoop van elk apparaat Onkyo TX-SR805 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Onkyo TX-SR805 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Onkyo TX-SR805 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Onkyo TX-SR805 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Onkyo TX-SR805 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Onkyo TX-SR805 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Onkyo TX-SR805 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Onkyo TX-SR805 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
