Gebruiksaanwijzing /service van het product C3407M-D van de fabrikant Pelco
Ga naar pagina of 24
INST ALLA TION ICS150-CW Series Camclosure ® Integrated Camera System Wide Dynamic Range (WDR) C3407M-D (1/07).
.
C3407M-D (1/07) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C3407M-D (1/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C3407M-D (1/07) 5 Description The ICS150-CW Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install.
6 C3407M-D (1/07) Figure 1. Package Components BACK BOX (1) CAMERA MODULE (1) TRIM RING, DOME LINER, AND CLEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-INCH HOLLOW SCREWDRIVER BIT (1) ADAPTER PLA TE (1) SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 1.
C3407M-D (1/07) 7 Cover and Back Box Installation The ICS150-CW Series Camclosure integrated camera system mounts only into a wall or ceiling. UNSHIELDED T WISTED PAIR (UTP) V IDEO The ICS150-CW Series offers support for unshielded twisted pair (UTP).
8 C3407M-D (1/07) SUSPENDED CEILING NOTE: Y ou should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera module to access the mounting holes. Refer to Camera Module on page 10 for more information.
C3407M-D (1/07) 9 4S DEEP ELECTRICAL BOX NOTE: Y ou should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera module to access the mounting holes.
10 C3407M-D (1/07) Camera Module The ICS150-CW Series Camclosure camera module includes the camera, camera bracket, and heater board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module.
C3407M-D (1/07) 11 2. Unplug the camera (10-pin), heater board (four-pin), and service (three-pin) connectors from the back box (refer to Figure 6). Figure 6.
12 C3407M-D (1/07) CAMERA ORIENTATION At the factory , the camera module is confi gured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image will be upside down. T o change the camera orientation (refer to Figure 7): 1.
C3407M-D (1/07) 13 Camera Adjustments T o perform the following camera adjustments, make sure to plug in the camera and service connectors. Y ou may have to remove the camera module from the back box. Connect a monitor . Then turn on power to the camera and monitor.
14 C3407M-D (1/07) SWITCH SETTINGS Locate the DIP switch (refer to Figure 9). Then set the switches for your installation. Figure 9. DIP Switch SW1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW2: Line Sync Set to ON to use AC line lock.
C3407M-D (1/07) 15 Extended dynamic range: Use for extremely high dynamic installations, for example, doorways, entrances, and exits. This profi le offers the maximum wide dynamic range. Fluorescent: Use for any installation with fl ickering lighting of any kind.
16 C3407M-D (1/07) Camera Positioning Manually rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis in Figure 11). NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in damage to the wiring.
C3407M-D (1/07) 17 Install Dome and T rim Ring 1. Adjust the dome liner if installed (refer to Figure 12): a. Align the screw holes in the trim ring with those in the back box to identify the proper dome liner position. b. Loosen the three Phillips screws located in the trim ring.
18 C3407M-D (1/07) Service Connector The ICS150-CW Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the fi eld of view and focus the camera. Figure 13. Service Connector Pelco offers two optional items that plug directly into the service connector .
C3407M-D (1/07) 19 T o assemble a longer service cable for the Camclosure integrated camera system, purchase the following from a local electronics supply store: 1 2.5 mm monaural headphone plug 1 CPM 88 miniature coaxial connector 1 RG174/U coaxial cable T o assemble the cable: 1.
20 C3407M-D (1/07) Specifications CAMERA Imaging Device 1/3-inch imager Dynamic Range 102 dB typical/120 dB maximum Picture Elements Sensor resolution: 742 (H) x 552 (V) Signal System NTSC or PAL Sca.
C3407M-D (1/07) 21 BACKBOX Electrical Input Voltage** 12 VDC or 24 VAC (±10%), autosensing Power Consumption 10 watts or less Video Connector Composite: BNC UTP: T wisted pair General Pan/T ilt Adjus.
22 C3407M-D (1/07).
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repa ir or replace, without charge, any merc ha ndise proved defective in material or wo rkmanship for a period of one year after the date of shipment.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
Een belangrijk punt na aankoop van elk apparaat Pelco C3407M-D (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco C3407M-D heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco C3407M-D vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco C3407M-D leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco C3407M-D krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco C3407M-D bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco C3407M-D kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco C3407M-D . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
