Gebruiksaanwijzing /service van het product C3468M van de fabrikant Pelco
Ga naar pagina of 44
INST ALLA TION C3468M (4/10) Spectra IV IP Series SD4E Dome System In-Ceiling Heavy-Duty In-Cei ling Pendant (shown).
.
C3468M (4/1 0) 3 Contents Important Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Legal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C3468M (4/10) List of Illustrations 1 Preparing the Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Attaching the Conduit Fitting, Lock Nut, and Safety Chain Bracket .
C3468M (4/1 0) 5 List of T ables A Video Coaxial Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 B 24 V AC/24 VDC Wiring Distances . . . . . . . . . . . . . . . . . . . . . . . .
6 C3468M (4/10) Important Notices LEGAL NOTICE SOME PELCO EQUIPMENT CONTAINS, AND THE SOFT W ARE ENABLES, AUDIO/VISUAL AND RECORDING CAP ABILITIES, THE IMPRO PER USE OF WHICH MA Y SUBJECT YOU TO CIVIL AND CRIMINAL PENAL TIES.
C3468M (4/1 0) 7 Description Spectra ® IV IP was designed wit h ease of installa tion and ease of maintenance in min d. Each dome system consists of three components: a back box, a do me drive, and a lower dome.
8 C3468M (4/10) Mounting IN-CEILING 1. Prepare the ceiling (refer to Figure 1): a. Locate the center point of the mounting location, and insert the compass tool into the ceiling. b. Place the end of a pencil in the hole on the end of the compass tool, and draw a circle.
C3468M (4/1 0) 9 4. Open the hinged door to the back box by pushing the tab lock toward the wall of the unit and lifting the door open. 5. Pull the wiring into the back box through the conduit fitting. 6. Connect all required wiring (refer to Wiring on page 12).
10 C3468M (4/10) Figure 4. Installing the Plates 5. Attach a conduit fitting (not supplied), lock nut (n ot supplied), and safety chain bracket (refer to Figure 2 on page 8). 6. Install a safety chain/cable (no t supplied), which will supp ort up to 16 pounds (7.
C3468M (4/1 0) 11 PENDANT, HEAVY-DUTY PENDAN T, AND STAINLESS STEEL 1. Install the mount for the pendant dome. Refer to the instruction s supplied with the mount. NOTE: If the mount is outdoors, make sure it is properly sealed to keep moisture out. 2.
12 C3468M (4/10) Wiring 1. Open the hinged door to the back box by pushing the tab lock toward the wall of the unit and lifting the door open (refer to Figure 7).
C3468M (4/1 0) 13 2. Remove the TXB-N from t he back box circuit board (refer t o Figure 8): a. Loosen the captive screw on the TXB-N. b. Carefully unplug the TXB-N from the back box circuit board.
14 C3468M (4/10) 3. Connect the auxiliary , alar m, and other wiring to the back box circuit board (refe r to Figure 9). NOTES: • Aux 1: Maximum 2 A at low voltage (<40 V) Aux 2: Maximum 30 mA at.
C3468M (4/1 0) 15 4. If you plan to use the audio functions, install your audio cables into the audio line-in and line-out connectors on the TXB-N. NOTES: • T o take full advantage of the distance and noise immunity benefits of audio, you must use a 600-ohm impedance matching transformer and twisted pair cable (refer to Figure 10).
16 C3468M (4/10) 5. Reinstall the TXB-N: a. Plug the TXB-N into the 1 6-pin connector located on the back box circuit board. b. Secure the TXB-N to the standoff on the circuit board using the captive screw on the TXB-N.
C3468M (4/1 0) 17 Refer to T able B for the recommended maximum distanc es fo r 24 V AC and 24 VDC applications, which are calculated with a 10 percent voltage drop. (T en perc ent is generally the maximum allowable voltage drop for AC- or DC-powered devices.
18 C3468M (4/10) Installing the Dome Drive 1. Perform one of the following options: • View vid eo using both analog and IP connections: Set the DIP switches on the top of the Spectra IV dome drive (refer to Figure 12). For DIP switch settings, refer to the labels located on the to p of the dome drive, or refer to Switch Settings on page 28.
C3468M (4/1 0) 19 Installing the Lower Dome IN-CEILING 1. Snap the clip on the en d of the trim ring leash into the hole on the lip of the back box (refer to Figure 13). Figure 13. Installing the In-Ceiling Lower D ome 2. Snap the trim ring into the plastic snap wash ers on the mounting screws.
20 C3468M (4/10) HEAVY-DUTY IN-CEILING 1. Snap the clip of the lower trim ring leash into th e hole on the lip of the back box (refer to Figure 14). 2. Insert both keys in the barrel locks. T urn the keys clockwise to the unlocked position. NOTE: Keys cannot be removed from the lock while in the unlocked position.
C3468M (4/1 0) 21 PENDANT 1. Attach the back box leash to th e lower dome (refer to Figure 15). Figure 15. Attaching the Leash to the Pendant Lower Dome 2. Push the lower dome into the back box. 3. T ighten the captive Phillips pan head screws to secure the lower dome.
22 C3468M (4/10) HEAVY-DUTY PENDANT 1. Attach the back box leash to the lower dome (refer to Figure 15 on page 21). 2. Lightly apply O-ring lubrican t (supplied with the lower dome) to the O-ring, and then install the O-ring in the groove on the trim ring of the lower dome (refer to Figure 17).
C3468M (4/1 0) 23 Figure 18. Installing the Heavy-Duty Pend ant Lower Dome ì Barrel Lock î Center Pin.
24 C3468M (4/10) STAINLESS STEEL 1. Attach the back box leash to the lower dome using the nearest retainer screw (refer to Figure 19). Figure 19. Attaching the Leash to the Stainless Steel Lower Dome 2.
C3468M (4/1 0) 25 4. Push the lower dome into the back box, line up the mounting screw holes, and install the two mounting screws (refer to Figure 20).
26 C3468M (4/10) T roubleshooting T o use your dome, refer to the operation and configuration manual. If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559-292-1981 (international) for assistance.
C3468M (4/1 0) 27 There is an echo when audio is received. The speaker volume is too high. Lower the speaker volume. The microphone and the speaker are too close together . If your call station does not h ave built-in echo cancellation, move the microphon e and speaker farther apart.
28 C3468M (4/10) Switch Settings WAR NIN G: If you are using Pelco D-type or Pelco P-type control, your system may not operate if the baud rate and address switches are not set correctly . The switches are set at the factory using the defaults for Pelco D-type control (2400 baud and address 1).
C3468M (4/1 0) 29 T abl e E. Switch Settings for SW1, Pelco P-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all s witches to OFF . For Pelco D-type control systems, refer to T able F on page 30.
30 C3468M (4/10) T able F . Switch Settings for SW1, Pelco D-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all switch es to OFF . For Pelco P-type control systems, refer to T able E on page 29.
C3468M (4/1 0) 31 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF 41 ON OFF OFF ON OFF ON OFF OFF 42 OFF ON OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON.
32 C3468M (4/10) 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF OFF ON OFF ON OFF 82 OFF ON OFF OFF ON OFF ON OFF 83 ON ON OFF OFF ON OFF ON OFF 84 OFF OFF ON OFF ON OFF .
C3468M (4/1 0) 33 120 OFF OFF OFF ON ON ON ON OFF 1 2 1 O N O F F O F F O NO NO NO N O F F 122 OFF ON OFF ON ON ON ON OFF 123 ON ON OFF ON ON ON ON OFF 124 OFF OFF ON ON ON ON ON OFF 125 ON OFF ON ON .
34 C3468M (4/10) 161 ON OF F OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF OFF OFF ON OFF ON 164 OFF OFF ON OFF OFF ON OFF ON 165 ON OFF ON OFF OFF ON OFF ON 166 OFF ON ON OFF O.
C3468M (4/1 0) 35 202 OFF ON OFF ON OFF OFF ON ON 203 ON ON OFF ON OFF OFF ON ON 204 OFF OFF ON ON OFF OFF ON ON 205 ON OFF ON ON OFF OFF ON ON 206 OFF ON ON ON OFF OFF ON ON 2 0 7 O NO NO NO N O F F .
36 C3468M (4/10) 2 4 3 O NO N O F F O F F O NO NO NO N 244 OFF OFF ON OFF ON ON ON ON 2 4 5 O N O F F O N O F F O NO NO NO N 246 OFF ON ON OFF ON ON ON ON 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF .
C3468M (4/1 0) 37 Specifications ELECTRICAL (Dome Drive Only) Input V oltage 18 to 32 V AC; 24 V AC nominal 22 to 27 VDC; 24 VDC nominal Input Power 24 V AC 23 V A nominal (indoor , without heater) 73 V A nominal (outdoor , with heater) 24 VDC 0.7 A nominal (indoor , without heater) 3 A nominal (outdoor , wit hout heater) Fuse 1.
38 C3468M (4/10) IN-CEILING Construction Back Box Plastic Dome Drive Aluminum, thermoplastic Lower Dome Acrylic Cable Entry (Back Box) 0.75-inch conduit fitting Pan Movement 360° continuous pan rotatio n V ertical T ilt Unobstructed +2° to –92° Manual Pan/Ti lt Speeds* Pan 0.
C3468M (4/1 0) 39 HEAVY-DUTY IN-CEILING Construction Back Box Aluminum Dome Drive Aluminum, thermoplastic Lower Dome Clear polycarbonate, 0.090-inch thick Cage Thickness 0.12 x 0.30-inch cast stainless steel Cage Color Black, for maximum discreetness Cable Entry (Back Box) 0.
40 C3468M (4/10) PENDANT Construction Back Box Aluminum Dome Drive Aluminum, thermoplastic Lower Dome Acrylic Cable Entry (Back Box) Throu gh 1.5-inch NPT pendant mount Pan Movement 360° continuous pan rotatio n V ertical T ilt Unobstructed +2° to –92° Manual Pan/Ti lt Speeds* Pan 0.
C3468M (4/1 0) 41 HEAVY-DUTY PENDANT Construction Back Box Aluminum Dome Drive Aluminum, thermoplastic Lower Dome Clear polycarbonate, 0.09-inch thick Cage Thickness 0.12 x 0.30-inch cast stainless steel Cage Color Black, for maximum discreetness Cable Entry (Back Box) Throu gh 1.
42 C3468M (4/10) STAINLESS STE EL Construction Back Box 316 stainle ss steel; gray , polyurethane powder-coated finish Dome Drive Aluminum, thermoplastic Lower Dome T rim Ring 316 stainless steel ; black, polyurethane powder-coated finish Bubble Acrylic, clear or smoked Cable Entry (Back Box) Throu gh 1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, an y merc handise pr oved defective in material or workmanship for a period of one year after the date of shipment.
Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .
Een belangrijk punt na aankoop van elk apparaat Pelco C3468M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco C3468M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco C3468M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco C3468M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco C3468M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco C3468M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco C3468M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco C3468M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
