Gebruiksaanwijzing /service van het product ICS210 van de fabrikant Pelco
Ga naar pagina of 20
® INST ALLA TION ICS210 Series Camclosure ® Integrated Camera System C2491M-C (1/06).
2 C2491M-C 1/06 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C2491M-C (1/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
4 C2491M-C (1/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C2491M-C (1/06) 5 Description The ICS210 Series Camclosure ® is a wedge style integrated camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the ICS210- CM corner mount. ICS210 system is shipped fully assembled.
6 C2491M-C (1/06) Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the ICS210. Use the screwdriver bit that is provided to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2).
C2491M-C (1/06) 7 4. Select a fixed or adjustable mounting pattern (refer to Figure 3 and Figure 4). Using the mounting plate as a template, mark the wire feedthrough and fastener hole positions on the mounting surface. Prepare the holes for the installation.
8 C2491M-C (1/06) INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length.
C2491M-C (1/06) 9 3. Using a blunt tool push out the wiring plug in the bottom of the base (refer to Figure 6). Pull the wiring inside the base. Figure 6. Removing the Wiring Plug 4. Insert the hole plug that is supplied into the hole in the base of the Camclosure (refer to Figure 7).
10 C2491M-C (1/06) 6. Install a 3/4-inch (1.91 cm) conduit connector in the conduit opening. Line up the mounting holes in the base with the mounting holes of the mounting plate. Attach the base to the mounting plate with the three 8-32 x 0.375-inch screws and lock washers previously removed.
C2491M-C (1/06) 11 ADJUST POSITION 1. T urn on power to the camera and monitor . 2. V arifocal lens only: Loosen the focal length and focus locking screws (refer to Figure 9). Adjust according to scene detail. Retighten the screws. Figure 9. V arifocal Lens Adjustment 3.
12 C2491M-C (1/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit.
C2491M-C (1/06) 13 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the iris level setting to increase or decrease brightness. Figure 11. Iris Level Adjustment FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, do the following: 1.
14 C2491M-C (1/06) HEATER BOARD REMOVAL T o remove the heater board, do the following: 1. Disconnect the four -pin heater connector (red, orange, and black wires) if it is plugged in. Figure 13. Removing Heater Board 2. Wait for the heater elements to cool if they are hot.
C2491M-C (1/06) 15 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to Figure 14. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture details.
16 C2491M-C (1/06) SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. Figure 16. Switch Settings for Varifocal Lens For manually setting and locking the white balance Place a white background in front of camera and turn off switch 1.
C2491M-C (1/06) 17 Specifications General Pan/T ilt Adjustment Manual; 5° above horizontal to 20° below horizontal tilt; 24° pan adjustment when using the adjustable mounting pattern in base Ratin.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
REVISION HISTORY Manual # Date Comments C2491M 6/05 Orginal version. C2491M-A 7/05 Revised per new camera shell design for varifocal lens. C2491M-B 10/05 Revised switch-setting descriptions for varifocal lens. C2491M-C 1/06 Revised factory switch settings for varifocal lens.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
Een belangrijk punt na aankoop van elk apparaat Pelco ICS210 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco ICS210 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco ICS210 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco ICS210 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco ICS210 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco ICS210 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco ICS210 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco ICS210 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
