Gebruiksaanwijzing /service van het product SD5AM van de fabrikant Pelco
Ga naar pagina of 28
SD5BC Series Color or SD5AM Series Monochr ome Spectra II™ Dome Systems Operation and Programming Manual C2419M-A (5/00) ® P elco • 3500 P elco Wa y • Clovis, CA 93612-5699 USA • www .
2 Pelco Manual C2419M-A (5/00) CONTENTS Section Page IMPORT ANT SAFEGU ARDS AND W ARNINGS ................................................................ 3 OPERA TION ...................................................................................
Pelco Manual C2419M-A (5/00) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and ser vicing should only be done by qualified service personnel and conform to all local codes.
4 Pelco Manual C2419M-A (5/00) OPERA TION POWER-UP DISPLA Y When the Spectra II™ dome is pow ered up , the selected protocol, re vision number , and other inf or mation is displa yed on the monitor .
Pelco Manual C2419M-A (5/00) 5 OPERA TING NOTES P AN AND TIL T FUNCTIONS Controller T ype Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Va r iab le speed 0.
6 Pelco Manual C2419M-A (5/00) PA TTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This patter n can consist of any standard pan and tilt or lens command. Presets, flip, and turbo are not allowed in a pattern.
Pelco Manual C2419M-A (5/00) 7 AUXILIAR Y OUTPUTS An A UX 1 command from the controller will activate the relay in the dome and oper ate the de vice that is connected to the relay .
8 Pelco Manual C2419M-A (5/00) PROGRAMMING Programming Guide - Spectra II LowLight Color Spectra II Monochrome 1. Access main menu (preset 95). 2. Make main menu selections . Joystic k: Move up or down to position cursor or to toggle between selections.
Pelco Manual C2419M-A (5/00) 9 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by progr amming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 f or Pelco’ s controllers varies according to the type of controller you are using.
10 Pelco Manual C2419M-A (5/00) ALARMS The Spectra II dome has se ven alarm inputs, which can be designated as either high or lo w prior ity . The high priority setting is significant when more than one alarm is activated. If pr iority in alarms is not required, leave all alarms in the low setting.
Pelco Manual C2419M-A (5/00) 11 6. P osition the cursor (>) beside the number of the alarm input for which you w ant to set the pattern. 7. Press the Iris Open button. The cursor mov es to the r ight, beside the words Full P at, Half P at 1, Half P at 2, or No Pattern.
12 Pelco Manual C2419M-A (5/00) AUTO FLIP There are two auto flip modes: On - Auto flip mode is enab led. Off - A uto flip mode is disabled. To change the auto flip mode: 1. Program preset 95 (28). The main menu appears. 2. P osition the cursor (>) beside Other.
Pelco Manual C2419M-A (5/00) 13 AUTO IRIS The following are the settings for auto iris: Mode Level Peak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
14 Pelco Manual C2419M-A (5/00) AUX MODE A ux Men u Aux 1 mode Normal Aux 2 mode Normal Exit Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT There are three settings for A UX mode: Normal - Controller operated.
Pelco Manual C2419M-A (5/00) 15 Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x- - Res.
16 Pelco Manual C2419M-A (5/00) LIMIT STOPS Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional .
Pelco Manual C2419M-A (5/00) 17 LINE SYNCHRONIZA TION Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Line Sync Menu Line sync On .
18 Pelco Manual C2419M-A (5/00) P ARK TIME MINUTES This feature causes the dome to park at preset 1 after a progr ammed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.
Pelco Manual C2419M-A (5/00) 19 This f eature lets the dome resume a desired condition follo wing power-up . The men u includes the following choices. Default - On power-up, the dome goes through a configuration cycle and stops at z ero ref erence, showing “Configur ation Done, ” address, and mode settings on the screen.
20 Pelco Manual C2419M-A (5/00) Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit.
Pelco Manual C2419M-A (5/00) 21 RESET CAMERA Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Resetting the camera returns the settings to their defaults .
22 Pelco Manual C2419M-A (5/00) SCAN SPEED Next Men u LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev .
Pelco Manual C2419M-A (5/00) 23 SHUTTER SPEED Next Men u LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to pre v .
24 Pelco Manual C2419M-A (5/00) WHITE BALANCE (Color Camera Only) Next Men u LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev .
Pelco Manual C2419M-A (5/00) 25 NOTE: The Spectra II LowLight Color camer a cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.
26 Pelco Manual C2419M-A (5/00) MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome’ s exterior surface with a nonabr asive cleaning cloth and cleaning agent that is safe f or acr ylic.
Pelco Manual C2419M-A (5/00) 27 Horizontal Resolution: >470 TV lines Lens Minimum f-stop 16X: F1.4 22X: F1.6 Focal Length 16X: 4 mm to 64 mm optical 22X: 4 mm to 88 mm optical Zoom Ratio Spectra II.
28 Pelco Manual C2419M-A (5/00) P elco, the P elco logo, Camclosure, Esprit, Genex, Legacy , and Spectra are registered trademarks of P elco . © Cop yr ight 2000, P elc o. Endura and ExSite are trademarks of P elco. All rights reser ved. U .S. P atent No .
Een belangrijk punt na aankoop van elk apparaat Pelco SD5AM (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelco SD5AM heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelco SD5AM vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelco SD5AM leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelco SD5AM krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelco SD5AM bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelco SD5AM kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelco SD5AM . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
