Gebruiksaanwijzing /service van het product PUV-Basic van de fabrikant Pelican
Ga naar pagina of 24
• A 5-micron (nominal) sediment filter must be installed upstream of (before) any UV system. • This product is for indoor use only . Keep all components clean and dry . • Clean the sleeve regularly for optimum performance. • Not for use in salt water applications.
P ot ential Hazar d Saf ety Measur es UV Exposure Never illuminate UV Lamp outside of the UV Chamber . Never look directly at illuminated UV Lamp, even when using protective gear . Always use protective gear , including gloves and UV safety glasses. If accidental exposure occurs, immediately cool affected area and consult ph ysician.
W ARNING – Alw ays shut-off w ater flow and release water pressure before servicing. T o guard ag ainst injury , basic safety precautions should be observed, including the following: 1.
INST ALLA TION W ARRANTY MAINTENANCE O VER VIEW T ABLE OF CONTENTS Overview 3 What model do I have? 3 Specifications 4 Components 5 Dimensions and layout 7 Installation 9 Installing the UV system 9 Di.
INST ALLA TION W ARRANTY MAINTENANCE OPERA TION O VER VIEW WHA T MODEL DO I HA VE? No-tools maintenance Ye s Ye s Ye s Safety cap & special lamp plug Ye s Ye s Ye s Lamp operation indicator Ye s Y.
INST ALLA TION W ARRANTY MAINTENANCE O VERVIEW SPECIFICA TIONS PUV -Basic PUV -8 PUV -16 Flow Rat es Rated ow for NSF Std 55, Class B 8.9 gpm (33.7 lpm ) 8.9 gpm (33.7 lpm ) 15.8 gpm (59.8 lpm ) Electr ical V oltage 100-240V AC 100-240V AC 100-240V AC Fr equenc y 50-60 Hz 50-60 Hz 50-60 Hz Max.
INST ALLA TION W ARRANTY MAINTENANCE OPERA TION O VER VIEW 3 2 For replacement components please contact your installer or contact VIQ UA directly for a referral: 1 80 0 265 7246 (Nor th America), 51 9 7 63 1 032, or info@viqua.
INST ALLA TION W ARRANTY MAINTENANCE O VERVIEW Lamp (includes O-rings) PUV -Basic, PUV -8 PUV -1 6 602805 602806 O-ring All -- Sleev e bolt All 602665 Sleev e (includes O-rings) PUV -Basic PUV -8 PUV -1 6 602732 602733 UV Chamber (includes Chamber clamp(s), and Ring clamp*).
INLET Clearance for lamp removal T o Drain 48” ( 122cm ) OUTLET A B C L D 6 1 2 3 5 4 12 13 11 10 7 14 Ø 16 8 9 L INST ALLA TION W ARRANTY MAINTENANCE OPERA TION O VER VIEW W ARRANTY L Model PUV-Basic 20.5" (52cm) 4" (10cm) 72" (183cm) 8.
INST ALLA TION W ARRANTY MAINTENANCE O VER VIEW W ARRANTY MAINTE- NANCE OPERA TION Sample valve: Allows for sampling of raw w ater . Shut-off valve: R equired to allow maintenance of pre-treatment equipment.
INST ALLA TION O VER VIEW MAINTENANCE OPERA TION Determine appropriate indoor location of the power supply and c hamber , referring to Dimensions and Layout drawing. P ower supply should be installed higher than c hamber away from all w ater sources. Ensure adequate clearance above c hamber to allow for removal of the lamp and sleeve.
Attac h ground (green/yellow) and strain relief (red) wires from the lamp plug to the ground lug on the c hamber . Secure both wires with loc king screw provided. 12 11 15 Let w ater flow to one faucet or other water outlet, then close the outlet and c hec k for leaks.
INST ALLA TION O VER VIEW MAINTENANCE OPERA TION UV systems disinfect the water using ultraviolet light, treating the w ater as it passes through the system. When there is a risk that water downstream of the UV system has been contaminated, it is critical that these water lines be c hemically disinfected.
INST ALLA TION O VERVIEW MAINTENANCE OPERA TION 8 Allow w ater to fill UV c hamber . Let the bleac h sit in the water lines for at least four hours. 11 Go to a water outlet and allow the cold water to flow until you can smell bleac h, then stop the flow.
INST ALLA TION O VER VIEW MAINTENANCE OPERA TION 19 17 Flush all water outlets until bleac h can no longer be smelled (at least 5 minutes). 18 20 21 16 W ARRANTY 13.
INST ALLA TION O VER VIEW MAINTENANCE OPERA TION Indicat or lights Lamp operating normally W ar ning; lamp will r equire replacement shortly Lamp disconnected; unplug system, reconnect lamp and plug-i.
INST ALLA TION W ARRANTY MAINTENANCE OPERA TION The table below is a list of possible causes and solutions. B efore replacing parts, please contact VIQUA T ec hnical Assist ance f or any ne w troubles.
INST ALLA TION O VER VIEW W ARRANTY MAINTENANCE OPERA TION Sleeve cleaning Minerals in the water slowly form a coating on the sleeve. This coating must be removed because it reduces the amount of UV light reac hing the water , thereby reducing purification performance.
INST ALLA TION O VER VIEW MAINTENANCE OPERA TION W ARRANTY 4 3 2 6 Let the system cool for 1 0 minutes. 5 1 7 8 Open a tap downstream of the UV unit to release pressure. Then, close this tap. Hold by sleeve bolt to remove lamp/sleeve assembly . Strain relief wires should remain connected.
INST ALLA TION O VER VIEW W ARRANTY MAINTENANCE OPERA TION 11 10 13 12 14 Remo ve o-rings and sleeve bolt from sleeve. Reinstall sleeve bolt with 2 new o-rings. Screw lamp into sleeve hand-tight. Caution: Over tightening will break the sleeve. 1 2 1 2 Lamp tab Sleeve bolt 2 1 Make sure lamp/sleeve assembly is centered.
INST ALLA TION O VER VIEW MAINTENANCE OPERA TION W ARRANTY 18 17 16 Push safety cap into place. 21 22 19 Disinfect the water lines. R efer to Disinfecting the W ater Lines in Installation section. If lamp was replaced and you have a PUV -8 and PUV -16 model: Press and hold Lamp timer reset but ton for 5 seconds.
INST ALLA TION O VERVIEW W ARRANTY MAINTENANCE OPERA TION Our Commitment VIQUA is commit ted to ensuring your experience with our products and organization exceeds your expectations. We have manufactured your UV purification system to the highest quality standards and value you as our customer .
.
Printed in Canada. Copyright ©20 14, VIQUA – a T rojan T echnologies Business, Guelph, Ontario, Canada..
Een belangrijk punt na aankoop van elk apparaat Pelican PUV-Basic (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Pelican PUV-Basic heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Pelican PUV-Basic vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Pelican PUV-Basic leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Pelican PUV-Basic krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Pelican PUV-Basic bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Pelican PUV-Basic kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Pelican PUV-Basic . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
