Gebruiksaanwijzing /service van het product R1V2 van de fabrikant AT&T
Ga naar pagina of 156
555-520-500 Issue 1, June 1987 AT&T SYSTEM 25 ADMINISTRATION MANUAL FOR R1V2.
©1987 AT&T All Rights Reserved Printed in USA TO ORDER COPIES OF THIS DOCUMENT REFER TO DOCUMENT NUMBER 555-520-500. Contact: Your AT&T sales representative or Call: 800-432-6600, Monday to Friday between 7:30 am and 6:00 EST, or Write: AT&T Customer Information Center 2855 North Franklin Road PO.
FCC WARNING STATEMENT Federal Communications Commission (FCC) Rules require that you be notified of the following: ■ This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
System 25 Documents The following System 25 product documents are available for your reference. Copies may be purchased from the Customer Information Center (CIC) by calling 800-432-6600.
Contents 1 2 3 4 Introduction Implementation Planning Forms The System Administrator’s Role Using this Manual How to Use the System Logging In to System 25 Correcting Typing Errors Making Backup Tap.
5 Administering Trunks 6 7 Assigning a Trunk Removing a Trunk Assigning Class of Service to DID Trunks Assigning Class of Service to All Other Trunks Administering Auxiliary Equipment External Alerts .
9 10 11 12 Administering Attendant Equipment Assign a Switched Loop Attendant Console Assign a Second Attendant Console Move an Attendant Console Change an Attendant PDC Remove an Attendant Console As.
13 14 15 16 17 Administering Tape Save/Restore Operations Using the Digital Tape Unit Save Your Translations Verify the Saved Translations Restore the System Translations from a Backup Tape System Sea.
Introduction This manual provides the information you need to administer AT&T System 25 station, network access, and system features. This includes configuring the system for initial service (that is, initializing the system) and making day-to-day changes required for efficient operation.
■ Maintaining system security. ■ Notifying company management (and AT&T) about problems, alarms, and service complaints. If you have questions about system hardware or features, you may want to refer to the AT&T System 25 Reference Manual for more information.
How to Use the System This chapter describes the way you interact with the system using the System Administration Terminal (SAT). First, it tells you how to log in to System 25. Then, how to use the Main Menu to access areas of the system you want to administer.
You can also end an administration session by: ■ Unplugging the cable from the modular jack connecting the terminal to the system. ■ Disconnecting the RS232 connector from the terminal. ■ Hanging up to drop the DTR signal on disconnect if you are connected via a modem.
The System 25 Administration Main Menu When you log in to the administration terminal, you see the Main Menu. This menu allows you to enter one of several command areas (Port, PDC, etc.
Selecting a Main Menu Item To select an item from the Main Menu, just type the number of the item you want followed by (Return) If you type (Return) by itself or if you type a number that is not betwe.
Command Functions The previous section introduced you to the basic command formats. This section shows you how to enter or change: an action number, data value, or target value.
Here is an example of the D command: You see : Port = 10604 Action = 7 Data = 0 > To change, you enter D 5 (Return) and see: > Data = 5 Port = 10604 Action = 7 Data = 5 > Changing a Target Va.
Here is an example of the T (target select) command with PDC (Main Menu item 2): You see: PDC = 9876 Action = 1 Data = 201 > You enter T 8765 (Return) and see: > PDC = 8765 Action = Action Groups Some action numbers are part of groups. These groups are sets of closely related system parameters that need to be changed as a group.
You enter 6789 (Return) and see: > Data = 6789 Port = 10408 Action = 2 Data = 6789 > There are no more members in this action group, so the system does not prompt for more data values.
You enter C and see: FPDC: Action = 1 Data = 7777 > You enter C and see: FPDC: Action = 1 Data = 8888 > You enter C and see: FPDC: Action = 1 Data = 9999 > You enter C and see: P16: END OF LIST FPDC: Action=1 Data=0 > You may also “abort” the list by typing a, d, or m.
System Responses During an administration session, there are occasions when you may enter inappropriate information at a prompt. While System 25 does not catch all input errors, it does catch many of them.
Print Messages This kind of message is straightforward–it conveys information. A print message does not describe an error condition. A print message appears at the end of certain search lists.
Initializing the System This section outlines the procedure for administering initial system translations (that is, for initializing) the system). To initialize the system, you must know the desired configuration.
TABLE 3-1 Default Dial Code Assignments Port Default Code Trunk Numbers (not part of dial plan) 0001-0104 Station Dial Codes: Multiline voice terminals 200-238 300-355 Single-line voice terminals 400-.
Initialization Sequence Begin with a Cold Start When you administer the initial translations, it is important that you begin from a known condition. You can establish a known condition by forcing a cold start (Menu 9, Action=20, Data=1 or 2).
TABLE 3-2 Initialization Sequence From the information provided on this form, Enter these translations: 1 System Options Form Enter system toll restriction options, pooled modem options, and other system options following the procedures in Administering System-Wide Options.
TABLE 3-2 Initialization Sequence (continued) 8 Voice and Data Station Records Assign all station ports (except for attendant consoles), form following the procedures in Administering Voice Stations and Administering Data Line and STARLAN CP Ports. Do not enter class-of-service parameters yet.
Administering System-Wide Options This section describes how to set system-wide options which include: ■ Toll Restrictions ■ Call Coverage ■ Pooled Modem Options ■ Time of Day ■ Dat e ■ Ca.
To allow toll restricted 1 At Action = , enter 31 . stations to make toll calls 2 At Data = , enter 1 for yes or 0 for no. The default is 1 . within your area code Specify whether your CO 1 At Action = , enter 32. requires you to dial “ 1” before dialing calls outside 2 At Data = , enter 1 for yes or 0 for no.
To specify the number of rings before calls are sent to call coverage or call following calls return to their home station 1 At Action = , enter 41 . 2 At Data = , enter a number between 0 and 31 for the number of rings.
To state whether there is 1 At Action = , enter 64. disconnect on received 2 At Data = , enter 1 for yes or 0 for no space The default is 1@ . To state whether the system should send a space character on disconnect 1 At Action = , enter 2 At Data = , enter 1 The default is 1@.
Call Accounting Options From the Main menu prompt, enter 4, then set the following call accounting options: SMDR Specify whether SMDR 1 At Action = , enter 52. records should be sent to the SMDR port 2 At Data = , enter 1 for yes or 0 for no. The default is 1@.
Miscellaneous System Options From the Main menu prompt, enter 4, then set the following system options: To block maintenance 1 At Action = , enter 70. busy of Ground Start trunks 2 At Data = , enter 0 for no or 1 for yes.
Administration Password To change the 1 From the Main menu prompt, enter 4 . administration password 2 At Action = , enter 75. 3 At Data = , enter the new password (eight or fewer printable characters, with no spaces). For security, the display always shows ????????.
To delete a code from the 1 At Action = , enter 3. list 2 At Data = , enter the code you want to delete exactly as it was listed using Action=1. Floating PDCs (FPDCs) From the Main menu prompt, enter 5; then follow the procedure below to list, add, or delete an FPDC.
Virtual Facilities A Virtual Facility (VF) is a call-routing facility which is not defined by the physical facility (trunk) over which calls are routed. Instead, the facility is defined by a combination of access codes, authorization codes, and coded characters that allow special handling of the destination telephone number.
System Speed Dialing System Speed Dialing allows you to enter a four-character code at any terminal to call the associated phone number. Keep the following considerations in mind when assigning System Speed Dialing codes: ■ Speed Dialing Codes range from # 100 through # 189 (including the # sign).
Administering Trunks This section shows you how to: ■ Assign and remove trunks ■ Assign class-of-service parameters for various types of trunks Assigning a Trunk To assign a trunk [AG] From the Main menu prompt, enter 1, then follow the procedures below to define the trunk type and assign a trunk number.
TABLE 5-1 Trunk-Type Codes If the Trunk Type is: You Enter: Ground Start, CO 701* Ground Start, WATS, FX 702 Loop Start, CO 801* Loop Start, WATS, FX 802 PBX/Centrex 805† DID Immediate Dial 901 DID .
Removing a Trunk To remove a trunk 1 From the Main menu prompt, enter 1. 2 At Port = , enter the physical port you want to remove in the form CSSPP. 3 At Action = , enter 1. 4 At Data = , enter 0. Note When you remove a trunk, any Display ID associated with the trunk is also removed.
TABLE 5-2 Trunk Class of Service (for all trunks except DID) COS NIGHT OUTWARD IN CODE SERVICE SIGNALING ONLY 0 TT 1 TT ● 2 TT 3 TT ● ● 4 DP 5 DP ● 6 DP 7 DP ● 8 ● TT 9 ● TT ● 10 ● T.
Class-of-Service Options Follow the procedures below to assign class-of-service options to this trunk. Pooled Facility Access 1 At Action = , enter 4. Group: Is this trunk in a 2 At Data = , if the trunk is in a pooled facility access pooled facility access group? group, enter the facility access code (FAC).
1 At 2 At ■ ■ Action = , enter 7 . Data = , enter: 1 to select Directed Night Service 0 to select TAAS Night Service. The default is 1. Delay Announcement: 1 At Action = , enter 8. To assign a Night Service delay announcement 2 At Data = , enter 1 for first delay announcement, 2 fo r second delay announcement, or 0 for none.
Assigning Trunk Options to a SLAC System The following options apply only to systems using the Switched Loop Attendant Console (SLAC), and are not administerable for DID trunks: To set the priority of a 1 At Action = , enter 11.
Administering Auxiliary Equipment This section discusses how to assign and remove AT&T System 25 auxiliary equipment associated with special ports.
Paging (Associated with Auxiliary Trunk Port) You can assign Paging to up to three zones. Each paging zone must be assigned to a separate port. Follow the procedure below to assign an access code and dial restriction to each zone.
Paging (Associated with CO Trunk Port) If the paging system is connected to a loop or ground start trunk port, simply assign a trunk facility access code for the port(s) so connected. DGC Delay Announcement To assign DGC Delay 1 At Action = , enter 1.
You see Action = 2. At Data = , enter: ■ 0 - if you do not want Music on Special Hold ■ 1 - if you want Music on Special Hold Pooled Modem To assign a Pooled Note See the procedure for setting pooled modem options Modem circuit pack under Administering System-Wide Options.
Administering Voice Stations ■ Assign voice terminals ■ Remove voice terminals ■ Assign and change station dial codes ■ Assign class of service Using the Port and PDC Menus: Class-of-service o.
TABLE 7-1 Voice Terminal Type Codes Terminal Type: Code: Single-line without message waiting indicator 201 Single-line with message waiting indicator 202 5-Button MERLIN CS Voice Terminal, Z7302H01 30.
4 5 At Data = , enter 0 . If this station is associated with another station(s) for features such as Call Coverage, Automatic Intercom, etc., you will see a warning message for each type of association. To go on with the action, respond to the system message, c for continue, any other key for abort.
Moving a Voice Station Use this procedure when you want to move a station – its features, button assignments, and PDC — to another port. Keep these considerations in mind when you move a station: ■ The moved-to port must be vacant. ■ The terminal types must be the same; that is, you can only move a station to the same physical type (e.
To restrict dial access to 1 At Action = , enter 4. all other trunk pools 2 At Data = , enter 1 for yes or 0 for no. The default is 0 . To restrict this station 1 At Action = , enter 13. from making any outward calls 2 At Data = , enter 1 for yes or 0 for no.
Station Hunting: To 1 At administer this station to hunt to another station if 2 At busy or Action = , enter 12. Data = , enter the PDC of the station to hunt to next, 0 for none.
To assign a trunk to this 1 At Action = , enter 52. station for Night Service 2 At Data = , enter a four-digit trunk number. Note Any given trunk can have no more than four Night Service coverage stations assigned to it. To delete a trunk from 1 At Action = , enter 53.
To assign a toll restriction 1 At Action = , enter 14. class 2 At Data = , enter a toll class number, 0-4, from the following list (the default is 0): 0 - Not toll restricted 1 - Toll call allowed lis.
Group Call Coverage: specify which receiver group will cover this station’s calls To 1 At 2 At ■ ■ ■ Action = , enter 7. ‡ Data = , enter a call coverage group number, 1-32 a DGC coverage group number, 101-132.
Night Service: To display 1 At Action = , enter 51 . the number of any trunks assigned to this station 2 To continue the list, enter C after each trunk number is for Night Service printed. To assign a trunk to this Note Any given trunk can have no more than four Night station for Night Service Service coverage stations assigned to it.
Administering Data Line and STARLAN CP Ports Procedures in this section apply to: ■ A data terminal connected to a Data Line Card (DLC) via an ADU, but not to a data terminal connected via a modem ■ A STARLAN Interface Circuit Pack (STARLAN CP) in DLC-compatibility mode.
4 At Data = , enter the code for the data terminal you’re adding: ■ 1801 for a DLC (ZTN126 or TN726) ■ 1802 for a STARLAN CP (ZTN84). Note The only way to change an existing terminal type is to remove and reinstall the station. 5 Next, assign a Data Dial Code (DDC): You see the prompt, Action = 2.
NO MORE BLOCKS c for continue, any other key for abort 5 Enter c. You see the following display when the station is removed: Action = 1 Data = 0 Note If you remove a station that is associated with other stations, you may need to reassign features on those other stations as well.
To move a data station to 1 From the Main Menu prompt, enter 2. a new port 2 At PDC = , enter the DDC of the station you want to move. 3 At Action = , enter 0. The system displays the station’s present port assignment at Data = CSSP P 4 Type d, and at Data = , enter the new port assignment (CSSPP).
To restrict access to all 1 At Action = , enter 4. other trunk pools 2 At Data = , enter 1 for yes or 0 for no. The default is 0 . To set calls to this station 1 At Action = , enter 12. to hunt to another station 2 At Data = , enter the DDC of the station to hunt to, or 0 if this station is busy for no hunt.
To assign ARS Facility 1 At Action = , enter 15. Restriction Level (FRL) 2 At Data = , enter the FRL number, 0-3, from the following list (the default is 3): Level Allowed FRL Pools 0- 0 1 - 0,1 2 - 0,1, 2 3 - 0,1,2, 3 To enter an associated 1 At voice/data station 2 At ■ ■ Action = , enter 21 .
Set Baud Rate and Parity Note For each data terminal, indicate all permissible operating speeds and any required parity. To auto-adjust baud rate 1 At Action = , enter 61. ‡ on call origination 2 At Data = , enter 1 for yes or 0 for no. The default is 1 for DLC and 0 for STARLAN CP.
Can this terminal operate 1 At Action = , enter 66. ‡ at a baud rate of 4800 bps? 2 At Data = , enter 1 for yes or 0 for no. The default is 0 . Can this terminal operate 1 At Action = , enter 67. ‡ at a baud rate of 9600 bps? 2 At Data = , enter 1 for yes or 0 for no.
To allow the user to 1 At Action = , enter 71. ‡ configure data port 2 At Data = , enter 1 for yes or 0 for no. The default is parameters 1. For a STARLAN CP, the default is 0. To permit mismatch of 1 At Action = , enter 72. ‡ baud rate between this port and a called port 2 At Data = , enter 1 for yes or 0 for no.
Administering Attendant Equipment System 25 can have two attendant consoles, either Switched Loop Attendant Consoles (SLACs) or Direct Trunk Attendant Consoles (DTACs). You cannot mix a DTAC and a SLAC in the same system; both consoles must be the same type.
Direct Extension Selector (DXS) Console System 25 assigns by default a selector (DXS) console, associated with the first attendant console, to the second ATL port in the system. Therefore, if you do not have a DXS console, you need to remove the default assignments before you can reassign this port.
Move an Attendant Console To move an attendant 1 From the Main menu prompt, enter 2. console to a different port (DTAC or SLAC) 2 At PDC = , enter the PDC for the attendant you want move. 3 At Action = , enter 0 4 At Data = , enter the new CSSPP for this attendant console.
To remove an attendant 1 From the Main Menu prompt, enter 1. console 2 At Port = , enter the CSSPP for the attendant console you’re removing. 3 At Action = , enter 1.
5 Type t and at Port = , enter the new CSSPP for the DXS console. 6 At Action = , enter 1. 7 At Data = , enter ■ 1601 for the first DXS console ■ 1602 for the second DXS console. Note When you move a DXS console, System 25 automatically reassigns the group select buttons you had administered for the previous port assignment.
Assign Attendant Options (DTAC and SLAC) To assign options to an From the Main menu prompt, enter 4. attendant console Assign options to the DTAC or SLAC as described below. To assign the number of 1 At Action = , enter 3. rings before unanswered calls extended by the 2 At Data = , enter the number of rings (1-31).
To assign the number of 1 At Action = , enter 7. rings before unanswered DGC calls are sent to the 2 At Data = , enter the number of rings, 1-31. delay announcement or a The default is 5.
To assign a DID access 1 At Action = , enter 84. code to the SLAC 2 At Data = , enter the DID access code people outside the system will use to call the attendant. (PDC format, no leading zeros, can’t exist in system number plan prior to this). To enable Automatic 1 At Action = , enter 85 .
SLAC Call-Type Options Call-type options let you set priorities for the eight types of calls that come into the attendant console queue. By default, the system sets the priorities for all call types to four, as shown in Table 9-1.
Assigning Message-Center-Like Defaults To specify which 1 At Action = , enter 90. attendant console should have message-center-like 2 At Data = , enter operation (for dual-SLAC ■ 1 for the first attendant systems only) Setting Follow ■ 2 for the second attendant ■ 0 for neither attendant The default is 0.
To specify which 1 At Action = , enter 91. attendant should receive each call type (dual-SLAC 2 At Data = , enter the call-type code, 1-8 (see Table 9-1).
Administering Button Assignments This section describes how to assign buttons to: ■ Multiline sets ■ Attendant consoles ■ Selector consoles Note Some button assignment features (e. g., Auto Intercom and Station-to-Station Message Waiting) require administering buttons on more than one voice terminal.
Selector Console (DXS) The selector console (DXS) has seven group select buttons that can be assigned, or “programmed.” (It also has a non-programmable test button located at the right-hand end of the button row. ) Each of the programmable buttons is a “base” number.
Button Assignment Tables TABLE 10-1 Multi line Set Button Defaults 7 - SYS ACCESS† 12 - FLEX DSS 17 - FLEX DSS 29 - FLEX DSS 8 - SYS ACCESS† 13 - ACCT ENTRY 18 - FLEX DSS 30 - FLEX DSS 9 - REP DIA.
TABLE 10-3 Direct Trunk Attendant Console (Cold Start Defaults) 7 - SYS ACCESS† 12 - FLEX DSS 17 - Trunk 0001 29 - Trunk 0009 8 - SYS ACCESS† 13 - ACCT ENTRY 18 - Trunk 0002 30 - Trunk 0010 9 - RE.
TABLE 10-5 DXS Console Button Defaults 2.. 3.. 4.. 5.. 6.. 7.. 8.. TEST† TABLE 10-6 MET Set Button Defaults 7 - SYS ACCESS† 8 - SYS ACCESS† 9 - REP DIAL 10 - REP DIAL 11 - LAST # DIALED Message† Drop† Conference† Transfer† Hold† † These buttons/features cannot be reassigned.
Assigning Buttons to Multiline Terminals and Attendant Consoles To assign a feature to a button on a multiline voice terminal or attendant console, begin with this step 1 From the Main menu prompt, enter 2. 2 At PDC = , enter the PDC of the voice terminal or attendant console.
5 You see the prompt, Action = 103. 6 Is this station the “owner” of this line? At Data = , enter 1 for yes or 0 for no. 7 You see the prompt, Action = 104. 8 At Data = , enter 1 to enable ringing at this set, 0 otherwise. To assign Exclusion 1 At Action = , enter 101.
To assign Automatic 1 At Action = , enter 101 . Intercom (AUTO ICOM) [AG] (This is a two- 2 At Data = , enter 8. station feature. ) 3 You see the prompt, Action = 102. 4 At Data = , enter the called station’s PDC. 5 You see the prompt, Action = 103.
To assign Call Coverage- 1 At Action = , enter 101 . Individual (COVER-IND) [AG] 2 At Data = , enter 12. † 3 You see the prompt, Action = 102. 4 At Data = , enter the covered station’s PDC. 5 You see the prompt, Action = 103. 6 At Data = , enter 1 to enable ringing (strongly recommended), 0 otherwise.
To assign an AUTO ANS 1 At Action = , enter 101. button 2 At Data = , enter 21. To assign Last Number 1 At Action = , enter 101. Dialed (LAST # DIALED) 2 At Data = , enter 35 .
To assign Position Busy Note For a DTAC, this feature can only be administered when (POS BUSY) there are two attendant consoles. For a SLAC, this feature can be administered when there are one or two consoles.
Administering Direct Group Calling (DGC) Groups This section tells you how to add DGC groups, assign access codes to DGC groups, and add and remove DGC group members. Keep the following considerations in mind as you administer DGC groups: ■ You can assign a maximum of 32 DGC groups; therefore, target values (i.
To disable DGC queuing 1 At Action = , enter 2. 2 At Data = , enter 1 for yes or 0 for no. The default is 0 . To list stations in a DGC 1 At Action = , enter 11.
Administering Automatic Route Selection (ARS) The procedures in this section show you how to define ARS patterns and lists. If you do not define these patterns and lists, then ARS calls will be routed over the local CO facility. For more information about making ARS choices, see the Reference Manual.
ARS Patterns The next set of procedures tells you how to assign routing patterns for “A” and “B” subpatterns. Each subpattern consists of a set of routes and associated Facility Restriction Levels (FRLs) plus DDD overflow authorization with an associated FRL.
To assign a stop time for 1 At Action = , enter 102. † subpattern A 2 At Data = , enter the stop time in the form HOUR, MINUTES (HHMM). To assign Route 1 for 1 At Action = , enter 110. † Subpattern A 2 At Data = , enter a Facility Access Code [FAC] or Virtual Facility Code [VFC].
To allow Subpattern A to 1 At Action = , enter 140. † overflow to DD D 2 At Data = , enter 1 for yes or 0 for no, The default is 0, To assign an FRL for 1 At Action = , enter 141.
To assign an FRL for 1 At Action = , enter 221. † Subpattern B, Route 2: 2 At Data = , enter an FRL, 0-3. To assign Route 3 for 1 At Action = , enter 230. † Subpattern B 2 At Data = , enter an FAC or VFC. To assign an FRL for 1 At Action = , enter 231.
Area Code Routing Table All North American area codes are assigned to routing pattern 1 by default, except area codes N00 and N10, which default to 0. To assign a different 1 At Action = , enter 300 . routing pattern to an area 2 At Data = , enter the area code.
Add Central Office Code 1 At Action = , enter 512. ‡ to this HAC exception list. 2 At Data = , enter a three-digit Central Office Code (NXX). Remove Central Office 1 At Action = , enter 513. ‡ Code from this HAC exception list. 2 At Data = , enter a three-digit Central Office Code (NXX) Display Central Office 1 At Action = , enter 511.
Other Area Codes Exception List Enter a Pattern Number 1 At Action = , enter 800 . to handle this Other Area Codes Exception 2 At Data = , enter a pattern number (1-8). Telephone Number. Add a number to the 1 At Action = , enter 822. † Other Area Codes Exception List.
Assign “associated” 1 At Action = , enter 701. ‡ Area Code. 2 At Data = , enter the associated area code. How many leading digits 1 At Action = , enter 702. ‡ should be removed for calls to the associated 2 At Data = , enter the number of digits (0-10).
Administering Tape Save/Restore Operations If you do not have a digital tape unit, you should skip this chapter. The procedures described below assume that your digital tape unit is correctly connected and turned on. See the System 25 Installation and Test Manual for further information.
4 Press the REWIND button, and wait for the tape unit to completely rewind tape. [You should do this before beginning any save, verify, or restore operation so you know that you are at the beginning of the tape. ] You do not have to be concerned about the clear “leader” material at the beginning and end of the tape.
To troubleshoot If the save is successful, the SAT displays: SAVE COMPLETED SUCCESSFULLY 5 Press the STOP/EJECT button on the tape unit. 6 Rewind the tape. 7 Follow the Verify procedure below. If the Save is not successful, the SAT displays: SAVE FAILED 1 Rewind the tape and repeat the Save procedure.
To troubleshoot 5 Rewind the tape. 6 Label the tape with the date and time. Store the tape in a safe place. If the verification is unsuccessful, the SAT displays: VERIFY FAILED 1 Rewind the tape and repeat the verification procedure. 2 If this verification is successful, follow steps 5 and 6 above.
To troubleshoot 4 Type c. The line now reads: Save/Restore: Action = 3 Data = 1 The tape unit automatically starts the Restore procedure at this point and stops when the restoration is complete.
System Searches This section describes how to search for various system information. Most searches require a minimum of two levels of search specification. The first level identifies what we might call the kind of search you want to begin (e.g., Search for Call Coverage Senders for a particular group).
PDCs of Group Call 1 At Action = , enter 1. Coverage Sender Stations 2 At Data = , enter 1 3 At Action = , enter 2. 4 At Data = , enter the call coverage group number, from 1-32, or 101-132 for a DGC coverage group number. 5 Enter C to initiate the search — here and in the remainder of search functions.
PDCs of Stations that Hunt to a Specified Station 1 At Action = , enter 1. 2 At Data = , enter 5. 3 At Action = , enter 2. 4 At Data = , enter the hunted-to station’s PDC. DGC Group Number for This search produces the DGC group number to which the a Specified Station specified station belongs.
PDCs of Call Pickup 1 At Action = , enter 1. Group Member Stations 2 At Data = , enter 9. 3 At Action = , enter 2. 4 At Data = , enter the call pickup group number, from 1 through 16. Assigned PDCs 1 At Action = , enter 1. 2 At Data = , enter 11. PDCs of Stations 1 At Action = , enter 1.
Note This search expects input in the form NNN or in the form N•• where N is the initial digit or two digits identifying the station, trunk, special port, data, or empty board for which you are searching and •• is the wildcard representation.
Translated Board Locations 1 At Action = , enter 1 2 At Data = , enter 17. 3 At Action = , enter 2. 4 At Data = , enter information from tables 16-26 and 16-27 in Chapter 16. To search for empty slots (board locations): 1 At Action = , enter 2. 2 at Data = , enter 0.
Port Location of External This search requires a PDC for input; it returns the port Alert location (CSSPP) of the external alert associated with the station. 1 At Action = , enter 1. 2 At Data = , enter 19. 3 At Action = , enter 2. 4 At Data = , enter the PDC of the station with external alert.
DDCs that can dial for a 1 At Action = , enter 1. station or data port via Third-Party Call Set-Up 2 At Data = , enter 22. 3 At Action = 2, enter the PDC or DDC being “dialed for” (the associated station). Permanent System 1 At Action = , enter 1.
Display Support Searches The Display Support feature lets you search for IDs (or names) associated with PDCs, DDCs, FPDCs, DGC groups, and trunk numbers. System 25 stores a maximum of 272 IDs in two alphabetical lists. One list is for trunk IDs, the other is for non-trunk IDs (the PDCs, DDCs, FPDCs, and DGCs).
Display ID for a Trunk 1 At Action = , enter 1. LDN (trunks only) 2 At Data = , enter 41. 3 At Action = 2, enter the trunk LDN. Number for a given 1 At Action = , enter 1. Display ID (non-trunk) 2 At Data = , enter 42. 3 At Action = 2, enter the Display ID for the PDC, DDC, FPDC, or DGC Display ID (enclosed in double quotes).
Listing Circuit Packs This item lets you list the board type, vintage, and cabinet location for each circuit pack in system, except the CPU and Memory CPs. When you enter Data= 50 for this action item, you see: SLOT CABINET 1 CABINET 2 CABINET 3 and the message, Type c to list.
Administering RS232 Parameters Action/data pairs associated with Main Menu item 10 (RS232) are used to administer System 25 peripheral equipment: System Administration Terminal, SMDR output port, and Digital Tape Unit. Any or all of these peripherals can be physically connected to System 25 via branches of an octopus cable.
1 At Action = , enter 1. Reassign an RS232 connector function 2 At Data = , enter the function you want to assign to the Target connector from the following list: 0 - None (disconnect function) 1 - Admin. (Target 1 or 4 only) 2 - SMDR (Target 2 or 3 only) 3 - Tape (Target 3 only) 4 - Reserved See footnote* on previous page for default function.
Command Referenc e LIST OF TABLES TABLE 16-1 PORT/PDC Administration, Voice Terminal (Menu=1/2) TABLE 16-2 Voice Terminal Type Codes TABLE 16-3 Feature Button Translation (Menu=1/2) TABLE 16-4 Multili.
Command Reference The tables in this chapter are intended to help those thoroughly familiar with system administration locate specific information without having to refer to the full text in the administration procedure chapters. Unless you are an experienced System Administrator, however, you should follow the administration procedures.
TABLE 16-1 PORT/PDC Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTION DATA 0 Physical port number CSSPP 1 Enter terminal type code [See Table 16-2] 2 Enter PDC [1-9999] 3 Restrict dial acc.
TABLE 16-2 Voice Terminal Type Codes If the Terminal Type is: Code: Single-line without message waiting indicator 201 Single-line with message waiting indicator 202 5-Button MERLIN CS Voice Terminal, .
TABLE 16-3 Feature Button Translation (Menu=1/2) “Action=100” is required before action(s) 101-104 listed in this table are administered. ACTION NOTES BUTTON TYPE ACTION 102 ACTION 103 101 1 (Note.
TABLE 16-3 10 Feature Button Translation (Menu=1/2) (continued) “Action=100” is required before action(s) 101-104 listed in this table are administered.
TABLE 16-4 Multiline Set Button Defaults 7 - SYS ACCESS† 12 - FLEX DSS 17 - FLEX DSS 29 - FLEX DSS 8 - SYS ACCESS† 13 - ACCT ENTRY 18 - FLEX DSS 30 - FLEX DSS 9 - REP DIAL 14 - SEND ALL CALLS 19 -.
TABLE 16-6 Direct Trunk Attendant Console Button Defaults (Cold-Start Defaults) 7 - SYS ACCESS† 12 - FLEX DSS 17 - Trunk 0001 29 - Trunk 0009 8 - SYS ACCESS† 13 - ACCT ENTRY 18 - Trunk 0002 30 - T.
TABLE 16-7 Direct Trunk Attendant Console Defaults (Administration-Installed Defaults) 7 - SYS ACCESS† 8 - SYS ACCESS† 9 - REP DIAL 10 - REP DIAL 11 - LAST # DIALED 12 - FLEX DSS 17- 0 29- 0 13 - .
TABLE 16-9 PORT/PDC Administration, Data Terminals (Menu=1/2) ACTION DESCRIPTION DATA 0 Physical port number CSSPP 1 Enter data type code [See Table 16-10] 2 Enter DDC [1-9999; 600-704] 3 Restrict dia.
TABLE 16-9 PORT/PDC Administration, Data Terminals (Menu=1/2) (continued) ACTION DESCRIPTION DATA 70 Allow keyboard dialing/Command Mode* [1=Y / 0=N] 71 Allow user configuration of data port [1=Y / 0=N] parameters.
TABLE 16-10 Data Port Type Codes IF THE DATA PORT TYPE IS Data Line Card (DLC) functionality for ZTN126 or TN726 STARLAN Interface Circuit Pack (STARLAN CP) in DLC- compatibility mode Disable this ind.
TABLE 16-11 Port Administration, Trunks (Menu=1) ACTION DESCRIPTION DATA 0 Physical port number CSSPP 1 Enter trunk port type code [See Table 16-12] 2 Enter trunk number [0001-9999; 0001-0104] 3 Assign class-of-service code [(DID—1-4; 3) (All other– See Table 16-13; 8)] 4 Assign pooled facility access code.
TABLE 16-12 Trunk Type Codes If the Trunk Type is: Ground Start, CO Ground Start, WATS, FX Loop Start, CO Loop Start, WATS, FX PBX/Centrex DID Immediate Dial DID Wink Start Auto-in/Auto-out Auto-in/Im.
TABLE 16-13 Trunk TRUNK CLASS-OF-SERVICE (FOR ALL TRUNKS EXCEPT DID) COS NIGHT OUTWARD IN SHORT CODE SERVICE SIGNALING ONLY DISCONNECT 0 TT 1 TT ● 2 TT ● 3 TT ● ● 4 DP 5 DP ● 6 DP ● 7 DP .
TABLE 16-14 Port Administration, Auxiliary Equipment (Menu=1) ACTION DESCRIPTION DATA 0 Display physical port number, in the form CSSPP 1 Enter special feature port type code (see Table 16-15).
TABLE 16-15 Special Feature Port Type Codes This table shows data values associated with Action = 1 on Table 16-14 TN742, FEATURE ZTN78 TN763 ZTN76 ZTN77 TN748 TN758 ZTN79 Tone Detector 2101 External .
TABLE 16-16 Port Options PORTS, Station/Trunk/Special Port Circuit Board Options FOR QUALIFIED SYSTEMS TECHNICIANS ONLY* (See Table 16-17 , “Applicable Options”) ACTION DESCRIPTION DATA 32 Set CO .
TABLE 16-17 Applicable Options See WARNING for Table 16-16. Also note that a bullet in a box on this table indicates that the default value for that action (shown in Table 16-16) is applicable for this circuit board. No bullet indicates that the option is not applicable.
TABLE 16-18 PDC Administration (Menu=2) ACTION DESCRIPTION DATA 0 Move this station to a new port [CSSPP (new port assignment)] (moved-to port must be vacant) 1 Display terminal type code [See Table 16-2] 2-53 All other See note below.
TABLE 16-19 System Administration (Menu=4) ACTION DESCRIPTION 3 4 5 6 7 11-18 25 26 25 26 27 30 31 32 33 34 40 Assign the number of rings before unanswered calls extended by Attendant return to the co.
TABLE 16-19 System Administration (Menu=4) (continued) ACTION DESCRIPTION DATA 41 Specify the number of rings before calls [0-31; 2] are sent to call coverage or call following calls return to their h.
TABLE 16-19 System Administration (Menu=4) (continued) ACTION DESCRIPTION DATA 82 Switched Loop Attendant system: Queue [group number (1-32), should act as coverage receiver for which 0 for NONE] call.
TABLE 16-20 Standard Call Type Defaults FOR SWITCHED LOOP SYSTEMS ONLY DEFAULT DEFAULT CALL TYPE CODE PRIORITY ATTENDANT Dial Attendant (0) 1 4 0 Call Following -- Logged into SLAC 2 4 NA Non logged i.
TABLE 16-22 Floating PDC Administration (Menu=5) ACTION DESCRIPTION DATA 1 List active FPDCs 2 Add an FPDC [FPDC to be added] 3 Delete an FPDC [FPDC to be deleted] 4 Enter existing FPDC to be named [F.
TABLE 16-24 Toll Calls Allowed (TCA) List Administration (Menu=7) ACTION DESCRIPTION DATA 1 List numbers in a TCA list 2 Add a number to the list [NXX or NPA-NXX] 3 Delete a number from the list [NXX .
TABLE 16-25 Searches: Action Items (Menu=8) ACTION DESCRIPTION DATA 1 Search for PDCs of call coverage senders 1 2 Call coverage receiver group [1-32 or 101-132 if DGC coverage group] 1 Search for sta.
TABLE 16-25 Searches: Action Items (Menu=8) (continued) ACTION DESCRIPTION DATA 1 Search for physical port locations 16 2 Port or board type (see Tables 16-26 and 16-27; 0 [port or board type] not app.
TABLE 16-26 Board Type—Wildcard Representation CATEGORY: BOARD DESCRIPTION: DATA: Empty Empty Slot (Searches 15 & 17 only) 0 Station Single-line Voice Terminal or Special Port 2 • • MERLIN C.
TABLE 16-27 Port/Board Type—Specific Representation CATEGORY: Voice Station Trunk DESCRIPTION: Single-line without message waiting Single-line with message waiting 5-Button MERLIN CS Voice Terminal .
TABLE 16-27 Port/Board Type—Specific Representation (continued) CATEGORY: DESCRIPTION: DATA: Special First Service Circuit 1101 External Alerts 253 First Paging Zone 1301 Second Paging Zone 1302 Thi.
TABLE 16-28 Save/Restore and System Restarts (Menu=9) ACTION DESCRIPTION DATA 1 Save (Backup) translations [1 to run] 2 Verify translations [1 to run] 3 Restore translations [1 to run] 10 Force a system warm start. FOR QUALIFIED [1 to run] SYSTEMS TECHNICIAN ONLY 20 Force a system cold start.
TABLE 16-30 Automatic Route Selection Administration (Menu=11) ACTION DESCRIPTION DATA 100 Assign a pattern number [1-8] 101 Assign a start time for subpattern 1A in the form [HHMM] HOUR, MINUTES (HHM.
TABLE 16-30 Automatic Route Selection Administration (Menu=11) (continued) ACTION DESCRIPTION DATA 401 Assign the ARS access code [dial code: 9] 402 Assign ARS pattern number for international calls [.
Requirements for the SAT This section defines requirements for the system administration terminal (SAT). Any data terminal with an RS-232C interface that meets the requirements below may be used as the SAT.
Index A Access code, speed dialing, 4-10 Access Toll Calls Allowed list, 4-7 Account Code Entry feature, 10-9 Account Codes, 4-5 Action groups, 2-7 – 2-8 Action number, 2-4 Action number, changing, .
D Data, 2-4 Data button, 10-8 search, 14-2 Data Line and STARLAN CP Ports, administration, 8-1 Data port, 2-6 Data stations, 3-5 administration, 8-1 Data terminals, class of service, 8-4 Data value, c.
N Night Service, 5-5, 7-6, 7-10 search, 14-4 Night Service button, 10-10 Night Service trunk, 2-9 Number of DID digits, 4-6 O On-line switch, 17-1 One-button transfer to data feature, 10-8 Other area .
Terminals, 3-5 Tie trunks, 5-6 Time of Day, 4-4 Toll Calls Allowed Lists, 2-9, 4-7 - 4-8 forms, 3-4 Toll restriction class, 7-5, 7-8 data stations, 8-5 Toll Restriction Options, 4-1 Tone detector, add.
Een belangrijk punt na aankoop van elk apparaat AT&T R1V2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AT&T R1V2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AT&T R1V2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AT&T R1V2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AT&T R1V2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AT&T R1V2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AT&T R1V2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AT&T R1V2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
