Gebruiksaanwijzing /service van het product UPAM-K van de fabrikant AT&T
Ga naar pagina of 25
AT&T UPAM-K Universal Paging Access Module Kit Installation Manual Document No. 518-600-031.
To Order Copies of This Manual: Your AT&T Information Systems Sales Representative or Call: Your Business Sales and Service Center or The AT&T Customer Information Center, 1-800-432-6600 AT&T Customer Information Center Write: P.
AT&T UPAM-K Universal Paging Access Module Installation Manual Issue 2, June 1990 Bogen Part No. 54-5916-02 Printed in U.S.A. 9006.
Federal Communications Commission (FCC) Statement (Part 68) This equipment is component registered with the Federal Communications Commission (FCC) in accordance with Part 68 of its rules. In compliance with the rules, be advised of the following: Registered equipment may not be used with Coin Telephone Lines.
1. 2. 3. 4. Table of Contents Product Identification UPAM-K Universal Paging Access Module Kit Overview Components Features Connection to the Telephone System General Instructions Specific Instruction.
1 1. Product Identification Installation Manual UPAM-K Universal Paging Access Module Kit The UPAM-K Universal Paging Adaptor Module Kit designed to provide telephone access to most commonly available paging systems.
Installation Manual 2 Features ● ● ● ● ● ● ● ● Acts as point of demarcation Acts as a point of demarcation between telephone system and customer paging equipment. 24V or 48V operation (trunk port operation) Mode switches let you select 24-volt or 48-volt operation.
3 UPAM Front Panel Installation Manual 405899972 AT&T UPAM Universal Paging Access Module BGM IN MODE OFF ON 24 VDC PWR SUPPLY — S1,S2 48 VDC PWR SUPPLY PHONE SYSTEM T S1,S2 — CONFIRMATION TONE S3 S4 R +M PREANNOUNCE TONE S4 S3 EXT VOX ENABLE -M VOX DISABLE S5 — PT VOX ENABLE — S5 PAGING OUTPUT PR PAGE PORT CONTACT CLOSURE N.
Installation Manual 4 2. Connection to the Telephone System General Instructions This section contains installation procedures for connection to the telephone system.
5 Installation Manual Specific Instructions Trunk Port Connections — Loop Start Controls for VOX Delay, Page Time, and Mode Switch S5 are not operable in this mode. Procedure 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Mount and ground the UPAM as described in the General Instructions.
Installation Manual 6 Specific Instructions Trunk Port Connections — Ground Start Controls for VOX Delay, Page Time, and Mode Switch S5 are not operable in this mode. Procedure 1. Mount and ground the UPAM as described in General Instructions. 2. 3.
7 Installation Manual 405899972 AT&T UPAM MODE 24 VDC PWR SUPPLY 48 VDC PWR SUPPLY CONFIRMATION TONE PREANNOUNCE TONE VOX DISABLE VOX ENABLE — S1,S2 S3 S4 S5 — S1,S2 — S4 S3 — S5 PAGE PORT INPUT Universal Paging Access Module BGM IN OFF ON T PHONE SYSTEM R + M EXT VOX ENABLE - M P T PAGING OUTPUT PR CONTACT CLOSURE N.
Installation Manual 8 Specific Instructions Station Port/Centrex Connections Disconnect methods In station port operation, the UPAM provides CPC — calling-party-controlled (loop current interrup- tion) disconnect, default timer disconnect, or optional voice-operated (VOX) disconnect.
9 Installation Manual Default Timer Modifications Inhibit default timer A field modification is available to inhibit the default timer. Do not inhibit the timer if jumpers J2 & J3 have been removed as outlined in Important Centrex Modification, below, and the VOX delay timer has been disabled (S5 is OFF).
Installation Manual 10 Ring delay Cutting jumper J1 increases the length of time it takes to answer the ringing line. This allows time for a talk path to be established before the UPAM answers, thereby ensuring that the preannounce or confirmation tone will be heard.
11 UPAM Printed Circuit Board (Rev. 8, 9, 10) Components Location Installation Manual Printed Circuit Board (Rev. 8) Components Location Printed Circuit Board (Rev.
Installation Manual 12 Specific Instructions Page Port Connections VOX DELAY, PAGING TIME, and Mode Switch S5 are not operable in this mode Procedure 1.
13 Installation Manual 405899972 PBX / KEY SYSTEM MODE OFF ON 24 VDC PWR SUPPLY 48 VDC PWR SUPPLY CONFIRMATION TONE PREANNOUNCE TONE VOX DISABLE VOX ENABLE — S1,S2 S3 S4 S5 — S1,S2 — S4 S3 — S5 PHONE SYSTEM T R EXT VOX ENABLE +M -M PAGE PORT PAGING OUTPUT P T PR MODULAR CONNECTOR PAGE PORT INPUT CONTACT CLOSURE N.
Installation Manual 14 3. Connection to the Paging System General Guidelines The UPAM is designed to connect to typical “centrally-amplified” and “self-amplified” paging and sound systems. “Centrally-amplified” systems generally use one amplifier to distribute the page audio to large numbers of speakers.
Installation Manual 15 PAGING AMPLIFIER WITH 600 OHM TELEPHONE INPUT VOX SENS TREBLE BASS BACKGROUND MUSIC SOURCE POWER PEAK LEVEL PAGE VOL MUSIC PUSH TO RESET CIRCUIT BREAKER MUTE VOL RING TIP COM 70.
Installation Manual 16 AT&T UPAM 48 VDC PWR SUPPLY CONFIRMATION TONE PREANNOUNCE TONE VOX DISABLE VOX ENABLE S1,S2 S3 S4 S5 — — S4 S3 — S5 EXT VOX ENABLE +M -M PT PR PAGING OUTPUT BGM VOL 60.
17 Installation Manual Connecting the UPAM to an amplifier’s MIC input Due to the higher sensitivity of microphone inputs, they should be used only as a last resort. The Lo-Z microphone connection is the more desirable of the two because it is less susceptible to noise pickup.
Installation Manual 18 Connecting the UPAM to a self-amplified paging system Connection to a self-amplified system usually consists of connecting the UPAM output to the line feeding the system’s self-contained amplifiers.
19 Installation Manual 4. TROUBLESHOOTING Functional Test Guide Use the following guide to troubleshoot problems that arise after installation. To start the test, pick up a telephone and call the UPAM.
Installation Manual 20 Procedure A 1. Disconnect the UPAM from the telephone equipment. 2. Confirm that the power supply is properly connected and that the mode switches are in the correct positions (make sure mode switches S3 and S4 are not in the same position).
Een belangrijk punt na aankoop van elk apparaat AT&T UPAM-K (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AT&T UPAM-K heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AT&T UPAM-K vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AT&T UPAM-K leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AT&T UPAM-K krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AT&T UPAM-K bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AT&T UPAM-K kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AT&T UPAM-K . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
