Gebruiksaanwijzing /service van het product 9390 van de fabrikant Powerware
Ga naar pagina of 206
INSTALLATION & OPERATION MANUAL UPS (40–80 kVA) www.powerware.com.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that you should follow during installation and maintenance of the UPS and batteries. Please read all instructions before operating the equipment and save this manual for future reference.
i Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Table of Contents 1I n t r o d u c t i o n 1 - 1 ............................................................ 1.1 Basic System Configurations 1 - 2 .............
Table of Con ten ts ii Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 5 Installing a Remote Em ergency Power -Off Control 5-1 ......................... 6 Installing Options and Accessories 6 - 1 ...............
Table of Con ten ts iii Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 8.1.6 LanSafe Power Management Sof tware 8 -2 ..................................... 8.1.7 Installation Features 8 -2 ......................
Table of Con ten ts iv Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 10.2 Multiple Module Parallel Operation 10 -8 .......................................... 10.2.1 Starting the Parallel System in Normal Mode 10 -8 .
Table of Con ten ts v Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 15 Product Specifications 15 - 1 ................................................... 15.1 Model Numbers 15-1 ................................
vi Powerware ® 9390 UPS ( 40–80 kVA) Inst allat ion a nd Op era ti on Ma nual S 164201535 Rev C List of Figures Figure 1-1. Powe rware 9390 UPS (40–80 kVA) Cabinet 1 - 1 ..................................... Figure 2-1. Powe rware 9390 UPS (40–80 kVA) Cabinet as Shipped on Pallet 2 - 3 .
vii Powerware ® 9390 UPS ( 40–80 kVA) Inst alla tio n and Op er at ion M anual S 164201535 Rev C Figure 9-24. C han ge Passw ord Scree n 9- 19 ................................................... Figure 9-25. C han ge Passw ord Save S cree n 9-20 ..
viii Powerware ® 9390 UPS (40– 80 kVA) I nstalla ti on and Ope rat ion M anual S 164201535 Rev C This page inten tionally left blan k..
1- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 1 Introduction The Powerware ® 9390 uninterruptible power sup ply (UPS) i s a true online, conti n.
Introduction 1- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 1.1 Basic System Configurations The following ba sic UPS system config urations ar e possible.
Introduction 1- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 1.2 Using This Manual This manual describes how to install a nd operate the Power ware 9390 UPS (40–80 kVA) cabinet. Rea d and understand the p rocedures descr ibed in this ma nual to ensur e trouble -free installation and operation.
Introduction 1- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 쑺 Chapter 14, “Maint aining the U PS System ” – contains maintena nce instructions for the UPS system. 쑺 Chapter 15, “Product Specificatio ns” – provid es detailed specification s for the UPS system.
Introduction 1- 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 1.4 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries.
Introduction 1- 6 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 1.5 For More Information Refer to the Powerware 9390 Integra ted Battery Cabinet (Mod els IBC.
1- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Section I Installation.
1- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C This page intentionally left blank..
2- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 2 UPS Installation Plan and Unpacking Use the following ba sic sequence of steps to i nstall the UPS: 1. Create an i nstallation pla n for the UPS system (Chapter 2).
UPS I nstallation Pla n and Unpacking 2- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 2.2.1 Environmental Considerations The life of the UP S system is ad.
UPS I nstallation Pla n and Unpacking 2- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Figure 2-1. Powerware 9390 UPS (40–80 k VA) Cabinet as Shi pped on Pallet CAUTION The UPS cabinet is heavy (see Table A on page A -3).
UPS I nstallation Pla n and Unpacking 2- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 3. Set the pallet on a firm, level surface, allowi ng a minimum clearance of 3m (10 ft) on each side for r emoving the cabi net from the pallet.
3- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 3 Installing the UPS System 3.1 Preliminary Installation Information WARNING Installation should be performed only by qualified personnel.
Installing the UPS System 3- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 3.2.1 Unloading the Powerware 9390 UPS Cabinet from the Pallet The UPS cabinet is bolted to a w ooden pallet suppor ted by wood skids.
Installing the UPS System 3- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C NOTE Do not discar d the fr ont anti -tip/shippin g bracket.
Installing the UPS System 3- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C Rear Shipping Bracke t Pallet Skid Bolts (3 Places) Removable Skid Rear View Shipping Bracket Bolts Shipping Bracket Bolts Figure 3-2.
Installing the UPS System 3- 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C NOTE In the following ste p the pallet tilts and ac ts as a ramp onc e the cabinet is rolle d beyond the the cen ter of the pal let.
Installing the UPS System 3- 6 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 3.2.3 Integrated Distribution Cabinet Installation To install an IDC, refer to the Powerwa re 9390 Integrate d Distri bution Cabi net (80 kVA) Installation and Operation Manual .
Installing the UPS System 3- 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 12. Connect phase A, B, C, a nd Neutral (if requir ed) bypass i nput power wi ring f rom the utility source to the byp ass input ter minals and neutral terminals i n the UPS cabinet.
Installing the UPS System 3- 8 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 23. After wiring the UPS system to the facility power and critic al load, be sure to ground the system according to local and/or national electr ical wiring codes.
Installing the UPS System 3- 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 8. Remove the UPS cabinet top or bottom conduit landing plate to drill or punch conduit holes (see Dr awing 164201535-6 on pag e A -27).
Installing the UPS System 3- 1 0 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 8. Route the UV trip and Aux wiri ng harness sup plied with the ba ttery cabinet f rom the battery cabinet to the UPS cabinet.
Installing the UPS System 3- 1 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 3.2.5.3 X -Slot Connections NOTE LAN and telephon e drops for use wi th X-Slot con nectivity cards mu st be provided by facility p lanners or custom er.
Installing the UPS System 3- 1 2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 3.4 Completing the Installation Checklist The final step in installing the UPS system is completing the following Installa tion Checklist.
Installing the UPS System 3- 1 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Installation Checklist - All packing materia ls and restrai nts have been removed from ea ch cabinet. - Each cabinet i n the UPS system is placed i n its installed location.
Installing the UPS System 3- 1 4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Parallel Syste m Installation Che cklist - Each cabinet in the para llel system is placed in its installed location. - All conduits and cables a re prop erly routed to the UP Ms and to the par allel tie or di stribution cabi net.
Installing the UPS System 3- 1 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Notes _________________________________________________________________________.
Installing the UPS System 3- 1 6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C This page intentionally left blank.
4- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 4 Batteries 4.1 Important Safety Instructions This chapter describes i nstalling the UPS batteries. CAUTION Only qualified servic e personnel (suc h as a licensed elec trician) should perform the battery installation.
Batteries 4- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C AVERTISSEME NT! 쑺 Les batteries peuvent présenter un risque d e décharge élec trique ou de brûlure par des courts -circuits de haute intensité.
5- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 5 Installing a Remote Emergency Power - Off Control A REPO switch can be used in a n emergency to shut down the UPS a nd remove power to the critical load from a location away from wher e the UPS is i nstalled.
Installing a Remote Emergency Power-Off Control 5- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 6. Remove the screws securing the internal panel cover ing the TB1 and TB2 ter minal blocks at the top of the UP S cabinet (see Dr awing 164201535-8 star ting on page A-33).
Installing a Remote Emergency Power-Off Control 5- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 13. If you are installing multiple REPO stations, wire ad ditional stations in parallel with the first REPO. 14.
Installing a Remote Emergency Power-Off Control 5- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C This page intentionally left blank.
6- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 6 Installing Options and Accessories 6.1 Installing a Hot Sync Computer Area Network Bridge Card A .
Installing Options and Accessories 6- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 6.2 Preliminary Wiring Procedure Perfor m the following pr ocedure before i nstalling wir ing: 1. If not alrea dy removed, remove the door.
Installing Options and Accessories 6- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 6.3 Installing Parallel System Control Wiring NOTE When insta lling exte rnal wiring to the X- Slot CAN card, co nduit must be installe d to the UPS cabinet.
Installing Options and Accessories 6- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 6.4 Installing a R emote Monitor Panel NOTE Only one system mon itorin g device can be connected to th e Hot Sync CAN Bridge Card at one time (see Table 6 -1).
Installing Options and Accessories 6- 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C NOTE Setup of the H ot Sync CAN Bridg e Card must be pe rformed by an authoriz ed Powerware Customer S ervice En gineer. Con tact service to schedu le a date.
Installing Options and Accessories 6- 6 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 6. Install conduit between the UP S and RIM. See Appendix A for UPS cabinet and RIM wiring acc ess inform ation. 7. Install wiri ng between the UPS and RIM.
Installing Options and Accessories 6- 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 6.6 Installing a Supervisory Contact Module NOTE Only one system mon itorin g device can be connected to th e Hot Sync CAN Bridge Card at one time (see Table 6 -1).
Installing Options and Accessories 6- 8 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 9. Install wiri ng between the SCM terminal block TB2 and the monitoring equipment. See Figur e 6 -2 f or termina l assignments a nd Drawing 164201535-8 for ter minal block location.
6- 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Section II Operation.
6- 1 0 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C This page intentionally left blank..
7- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 7 Understanding UPS Operation 7.1 Looking Inside the UPS System The Powerwar e 9390 UPS is a conti .
Unders tandin g UPS Op erati on 7- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C If utility power is interrupted or falls outside the parameters spec ified.
Unders tandin g UPS Op erati on 7- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The UPS continua lly monitors itself a nd the incoming utili ty power, and automa tically switches between these modes as req uired, without oper ator inter vention.
Unders tandin g UPS Op erati on 7- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 7.2.2 Normal Mode – RT Figure 7-2 shows the p ath of electrical power throug h the UPS system when the UPS is operating in Normal mode.
Unders tandin g UPS Op erati on 7- 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The neutral from the system input i s connected to the neutral regulator in the DC capaci tors.
Unders tandin g UPS Op erati on 7- 6 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 7.2.3 Bypass Mode – RT The UPS automati cally switches to Bypa ss mode if it detects an overloa d, load fault, or i n t e r n a lf a i l u r e .
Unders tandin g UPS Op erati on 7- 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C During an outage, the UPS prohibi ts transfers to byp ass and provi des upstream p rotection.
Unders tandin g UPS Op erati on 7- 8 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 7.2.4 Battery Mode – RT The UPS automatically transfer s to Battery mode if a utility power outage occurs, or if the utility power does not conform to specif ied parameter s.
Unders tandin g UPS Op erati on 7- 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C If the input p ower fai ls to return or is not wi thin the accepta nce wind.
Unders tandin g UPS Op erati on 7- 1 0 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Up to four units can be paralleled for redunda ncy or capacity without any addi tional cabinets.
Unders tandin g UPS Op erati on 7- 1 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 7.3.2 Normal Mode – Parallel In Normal mode, util ity AC power i s supplied to the UP Ms.
Unders tandin g UPS Op erati on 7- 1 2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 7.3.3 Bypass Mode – Parallel In Bypass mode, the output of the system i s provided with thr ee -p hase AC power dir ectly from the bypa ss input.
Unders tandin g UPS Op erati on 7- 1 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The parallel system can be tran sferred from Normal mode to Bypass m ode manually. However, the par allel system automatica lly switches to Bypass mode whenever the UPMs can no longer sup ply the criti cal load.
Unders tandin g UPS Op erati on 7- 1 4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 7.3.4 Battery Mode – Parallel The UPMs transfer to Battery mode automatically if a utility power outage occurs, or if the utility power does not conform to specif ied parameter s.
Unders tandin g UPS Op erati on 7- 1 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C If the input p ower fai ls to return or is not wi thin the accepta nce wi.
Unders tandin g UPS Op erati on 7- 1 6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C An ABM chargi ng cycle starts with the cha rger dri ving the battery volta ge, at max imum current limit, to a battery char ge level of 2.
8- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 8 Features, Options, and Accessories 8.1 UPS Standard Features The UPS has ma ny standard fea tures that pr ovide cost-effecti ve and consistently relia ble power pro tectio n.
Features, Options, a nd Accessories 8- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 8.1.5 Advanced Battery Management A three-stag e charging system incre.
Features, Options, a nd Accessories 8- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 8.2.3 HotSync Parallel System A para llel UPS system with two to four uninterrupti ble power modules can be installed to provide a parallel capacity and /or redund ant sys tem.
Features, Options, a nd Accessories 8- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 8.3 Symbols, Controls, and Indicators T h ef o l l o w i n ga r ee x a.
9- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 9 Using the Control Panel This chap ter describes the UPS control panel, includi ng controls and indicators, and how to monitor UPS oper ation. The control panel (see Figure 9-1) is located on the front door of the UPS.
Using the Control Panel 9- 2 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 9.1 Using the LCD and Pushbuttons The LCD on the control p anel provides a n operator i nterface with the UP S system. Figure 9-2 identi fies the displa y areas discussed i n the following sections.
Using the Control Panel 9- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.2 Using the Main Menu The UPS main menu bar allows yo u to display data in the information area to help you monitor and contr ol UPS opera tion.
Using the Control Panel 9- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 9.2.2 Event Screens Press the EVENTS pushbutton on the ma in menu bar or Histor y Menu bar to displa y a listing of a ll system events that are curr ently active.
Using the Control Panel 9- 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Press the HISTORY pushbutton on the Active Events Menu bar to display the History Log.
Using the Control Panel 9- 6 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 9.2.3 Unit Meter Screens The Unit Meter screens show the UPS meter readings f or the unit (or units, if a p arallel system is installed).
Using the Control Panel 9- 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Input screen shows i nput voltage (pha se -to- phase), output curr ent (each phase), and frequency o f the incoming utili ty source, as well as the kVA, kW, a nd power factor measurements.
Using the Control Panel 9- 8 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C The Battery screen displays the batter y voltage (Vdc), the battery current (Idc), and the minutes of batter y time remai ning. When batter y life decrea ses to less than 20%, Check Battery is disp layed.
Using the Control Panel 9- 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.2.4 Sys tem Meters Screens The System Meters scr eens show the total system and indivi dual UPS uni t meter reading s from any unit, when a par allel system is installed.
Using the Control Panel 9- 1 0 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Output Total System screen shows output voltage (pha se -to-neutr al), output current (each phase), and f requency being sup plied by the UPS, a s well as the kVA, kW, and power factor mea surements for the total system.
Using the Control Panel 9- 1 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Figure 9-13 throug h Figure 9-17 show the System Meters scr eens. To scroll thr ough the meter screens, press the or pushbuttons on the menu bar.
Using the Control Panel 9- 1 2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Input screen shows i nput voltage (pha se -to- phase), output curr ent (each phase), and frequency o f the incoming utili ty source, as well as the kVA, kW, a nd power factor measurements for the selected unit.
Using the Control Panel 9- 1 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Battery screen displays the batter y voltage (Vdc), the battery current (Idc), and the minutes of batter y time remaini ng for the selected unit.
Using the Control Panel 9- 1 4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.2.5 System Setup Level 0 Screens Press the SETUP pushbutton on the main menu bar to display the System Setup Level 0 Screen. This scr een can be used to: 쑺 Enter a p assword to access Level 1 functions (see par agra ph 9.
Using the Control Panel 9- 1 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Select CONTRAST from the System Setup L evel 0 menu to display the Contr ast Adjust screen. Fig ure 9-19 shows the Contrast Adjust scr een.
Using the Control Panel 9- 1 6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Select VERSIONS from the System Setup Level 0 menu to displa y the Versions scr een. The Versions screen p rovides the fir mware version number s installed on the UPS.
Using the Control Panel 9- 1 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.2.6 System Setup Level 1 Screens A password i s required to access the Level 1 functi ons. To enter the pa ssword, select ENTER PASSWORD from the System Setup Level 0 menu to display the Enter Passwor d screen.
Using the Control Panel 9- 1 8 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The System Setup Level 1 screen can be used to set the UPS date and time, the serial p orts, change the Level 1 p assword, and log out of Level 1.
Using the Control Panel 9- 1 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Select CHANGE P ASSWORD from the System Setup L evel 1 menu to display the Cha nge Password scr een. The Change P assword screen allows the System Setup Level 1 passwor d to be changed.
Using the Control Panel 9- 2 0 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Change P assword Save screen lets you save the new p assword, retr y another password, or abort t he password chang e. Figur e 9 -25 shows the Cha nge Passwor d Save screen.
Using the Control Panel 9- 2 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Select DATE AND TIME from the System Setup Level 1 menu to display the Time Format Setup screen.
Using the Control Panel 9- 2 2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Set Date and Time MM/DD/YYYY screen allows th e internal date and tim e of the UPS to be set in the month/day/year format.
Using the Control Panel 9- 2 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The Set Date and Time DD/MM/YYYY screen allows th e internal date and tim e of the UPS to be set in the day/month/year format.
Using the Control Panel 9- 2 4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Select COM P ORT SETUP from the System Setup Level 1 menu to displa y the COM Por t Setup screen. Thi s screen allows selection of the seri al COM p ort to set up.
Using the Control Panel 9- 2 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The COM Setup scr een is used to change and save the setti ngs for the seri al communication por ts. The COM port number selected from the COM Port Setup screen displa ys.
Using the Control Panel 9- 2 6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.3 System Controls Screen Press the CONTROLS pushbutton on the main menu bar to display the System Controls screen.
Using the Control Panel 9- 2 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C SYSTEM CON TROLS LO A D O F F P M O F F CHGR ON MAINTENANCE B Y P AS S BY P A S S POWER MODULE (PM) OFF : OFF : ONLINE : CHARGER OFF : Figure 9 -32.
Using the Control Panel 9- 2 8 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.4 Load Off Screen The Load Of f screen appea rs when the LOAD O FF pushbutton is selected from the ma in menu bar or System Contr ols Menu bar.
Using the Control Panel 9- 2 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.5 Reading the Status Indicators The four symbols on the right side of the control panel are status indicator s .
Using the Control Panel 9- 3 0 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C This page intentionally left blank.
10-1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 10 UPS Operating Instructions The following pr ocedures provi de instr uctions for operating the UP S or parallel system. For a descripti on of the UPS control panel f unctions, see Chapter 9, “Using the Control P anel.
UPS Operating Instructions 10-2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 7. Observe the following messa ges appea r sequentially on the p ower module (PM) status line: DC STARTING INVERTER STARTING INVERTER SYNCING READY ONLINE The rectifier a nd inverter turn on.
UPS Operating Instructions 10-3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 10.1.3 Starting the Power Module To start the po wer modu le witho ut trans ferring the c ritical load t o normal, pe rform the following procedure: 1.
UPS Operating Instructions 10-4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 3. The UPS is now o perating in Bypass mode and the BYPASS status indicator i s illuminated. The power module (PM ) status indicates RE ADY.
UPS Operating Instructions 10-5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 10.1.7 UPS and Critical Load Shutdown To perfor m maintenance or service on the criti cal load, shut down power to the loa d by perfor ming the following pr ocedure: 1.
UPS Operating Instructions 10-6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 10.1.9 Using the UPS LOAD OFF Pushbutton AU P SL o a dO f fi si n i t i a t e db yt h e LOAD OFF pushbutton fro m the main menu bar or the System Controls menu bar.
UPS Operating Instructions 10-7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 10.1.10 Using the Remote Emergency Power-Off Switch A UPS emergency power -off is initiated by th e REPO pushbutton switch. In a n emergency, you can use this switch to control the UP S output.
UPS Operating Instructions 10-8 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 10.2 Multiple Module Parallel Operation 10.2.1 Starting the Parallel System in Normal Mode To start t he parallel system, perform the f ollowing procedur e: 1.
UPS Operating Instructions 10-9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 10.2.2 Starting the Parallel System in Bypass Mode If the inverter output of the.
UPS Operating Instructions 10-10 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 10.2.3 Transfer Parallel System from Normal to Bypass Mode To transf er the cr.
UPS Operating Instructions 10-11 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 10.2.5 Single UPM Shutdown To shut down a sing le UPM, per form the following procedure: NOTE The UPM can be shut dow n only if remaining UPMs can suppo rt the critical load with out being overl oaded.
UPS Operating Instructions 10-12 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 7. Press the NORMAL pushbutton on the System Controls menu ba r of the UPM .
UPS Operating Instructions 10-13 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The input, output, a nd bypass backfeed conta ctors open, the battery breaker or disconnect is tri pped, and the power module is turned off immediat ely, without asking for verification .
UPS Operating Instructions 10-14 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 10.2.9 Using the Parallel System Rem ote Emergency Power - Off Switch A parallel system emergency power-off is initiated by the REPO p ushbutton switch.
11-1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 11 Using Features and Options The many standar d features of your UPS system p rovide consistent, economical, a nd dependable power protection. In additi on, you can add availa ble options to enhance t he perfor mance of your system.
Using Features and Options 11-2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 11.3 Optional Remote Monitor Panel As an option, a Remote Monitor Panel (RMP) can be installed to monitor the op eration of the UPS system fr om virtually a ny location within the f acility, up to 152.
Using Features and Options 11-3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C The RMP contain s a local horn and th e backlit statu s indicators listed in Table 11 -2.
Using Features and Options 11-4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 11.4 Relay Interface Module An optional RIM uses relay contact closur es to indicate the operating status and alarm condition of the UPS system.
Using Features and Options 11-5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 11.5 Supervisory Contact Module An optional SCM establishes an interface between the UP S system and the customer’s monitor. This interface allows the customer t o monitor operational status of the UP S system equipment.
Using Features and Options 11-6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C This page intentionally left blank.
12-1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 12 Responding to System Events 12.1 General When the UPS system is r unning in Normal mode, it continually moni tors itself and the incoming utility power.
Responding to System Events 12-2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C ALARMS Message Hor n Phon e Relay Log* Indication Battery Totally Discharged 1.
Responding to System Events 12-3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C ALARMS Indication Log* Relay Phon e Horn Message Configuration Error 1 No 1 HA .
Responding to System Events 12-4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C ALARMS Indication Log* Relay Phon e Horn Message L3 Overload (High Level) 1 No.
Responding to System Events 12-5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C NOTICE S Message Hor n Phon e Relay Log* Indication Automatic Shutdown Pending .
Responding to System Events 12-6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C NOTICE S Indication Log* Relay Phon e Horn Message Input AC Over Voltage 1 No .
Responding to System Events 12-7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C NOTICE S Indication Log* Relay Phon e Horn Message Output AC Under Voltage 1 No.
Responding to System Events 12-8 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C STATUS Message Hor n Phon e Relay Log* Indication Battery Switc hgear Closed N.
Responding to System Events 12-9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C COMMAN D Message Hor n Phon e Relay Log* Indication Load Off Command Received Y.
Responding to System Events 12-10 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C This page intentionally left blank.
13-1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 13 Communication This chap ter describes the communicati on features of the Powerware 9390 40–80 kVA UPS and provides inf ormation about connecting ha rdware and using T erminal mode.
Communication 13-2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C Relay Interface Card Modem Card Modbus Card ConnectU PS -X We b/SNMP Card Hot Sync CAN Bridge Card Industrial Relay Card F i g u r e1 3 - 1 .O p t i o n a lX - S l o tC a r d s 13.
Communication 13-3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Remote Notification differs from the basic Terminal mode with the addition the following functions: 쑺 Call Answer The Call Answer function allows the user to call into the UPS from a remote l ocation and e nter Te rminal m ode.
Communication 13-4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 13.4.2 Event History Log This key sequence p rints the entire E vent History Log of the UPS at the ti me the data is requested. The p rintout begi ns with the oldest alar m entry in the queue a nd ends with the most recent.
Communication 13-5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 03/1 1/2004 14:13:03.000 ST A TUS: CSB Powe r Supply On 03/1 1/2004 14:13:03.043 NOTICE: Inverter Initializing 03/1 1/2004 14:13:05.721 ST A TUS: UPS Power Suppl y OK 03/1 1/2004 14:13: 05.
Communication 13-6 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C This page intentionally left blank..
14-1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 14 Maintaining the UPS System The components inside the UP S cabinet a re secured to a sturdy metal frame. All repai rable parts a nd assemblies are loca ted for easy remova l, with very little disassembly.
Maintaining the UPS System 14-2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 쑺 Determ ine if the b atte ry is inadve rten tly groun ded . If it is, rem ove th e sou rce of the ground. Contact wi th any part of a grounded battery can result in electri cal shock.
Maintaining the UPS System 14-3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 3. Ensure the op erating envi ronment is wi thin the par ameters speci fied in Chapter 15, “Product Specifica tions,” a nd Drawi ng 164201535-2 on pag e A-3.
Maintaining the UPS System 14-4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C This page intentionally left blank.
15-1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Chapter 15 Product Specifications 15.1 Model Numbers The UPS systems are housed in free-standi ng cabinets with safety shields behind the doors. The UPS systems ar e available i n 50/60 Hz with various outp ut power ra tings.
Product S pecifications 15-2 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C 15.2.2 UPS System Output UPS Output C apacity 100% rated current Output Voltage Re.
Product S pecifications 15-3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 15.3 Multiple Module Parallel Specifications 15.3.1 UPM Input Same as sing le module. 15.3.2 UPM Output Same as sing le module. 15.3.3 Environmental Same as sing le module.
Product S pecifications 15-4 Powerware ® 9390 UPS (40–80 kVA) Installation and Operatio n Manual S 164201535 Rev C This page intentionally left blank.
A- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Appendix A 16 - Installation Information The informa tion in this ap pendix is help ful during the planning a nd installation of the UPS system.
BA TTERY CABI NET UPS CABINET DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 164201535 - - - 1 1 of 1 TYPICAL POWERWARE 9390 UPS SYSTEM 111504 B Installation Informa tion A- 2 Powerware ® 9390 .
DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 164201535 - - - 2 1 of 2 PHYSICAL FEA TURES AND REQUIREMENTS 111504 B Installation Informa tion A- 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 1.
2o f2 PHYSICAL FEA TURES AND REQUIREMENTS 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 2 Installation Informa tion A- 4 Powerware ® 9390 UPS (40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C 7.
1o f1 UPS SYS TEM ONE LINE CONFI GURA TIONS 111504 B 164201535 - - - 3 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: Installation Informa tion A- 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C T able D.
BATTERY BREAKE R 1o f5 UPS SYS TEM ONE LINE DR AWI NG 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 4 UPS CAB INET INVERTER RECTIFIER STA TIC SWITCH REMOTE EPO BUILDING.
2o f5 UPS SYS TEM ONE LINE DR AWI NG 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B MAINTENA NCE B Y PA S S PA N E L (PRO VIDED B Y OTHER S) Output from UPS MIB To U P S Input MIB: MAIN.
UPS SYS TEM ONE LINE DR AWI NG 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B OUTPUT TO CRITICAL LOAD BA TTERY CABI NET BATTERY BREAKER E4.
UPS SYS TEM ONE LINE DR AWI NG 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B T Y P I C A LP A R A L L E LS Y S T E M (2+1 AND 3+0 CONFIGURA TIONS) 4o f5 164201535 - - - 4 NOTE: 1. UPM and system bypass input feeds must come from the same source.
UPS SYS TEM ONE LINE DR AWI NG 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B T Y P I C A LP A R A L L E LS Y S T E M (3+1 AND 4+0 CONFIGURA TIONS) 5o f5 164201535 - - - 4 NOTE: 1. UPM and system bypass input feeds must come from the same source.
1o f1 6 POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 Installation Informa tion A- 1 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C T able E.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 2 of 16 Installation Informa tion A- 1 2 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C T able F.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 3o f1 6 Installation Informa tion A- 1 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C T able G.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 4o f1 6 Installation Informa tion A- 1 4 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C T able H.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 NOTE: Customer ground can be run in any conduit listed in T a ble K. 5o f1 6 Installation Informa tion A- 1 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 8.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 NOTE: Customer ground can be run in any conduit listed in T a ble K. 6o f1 6 Installation Informa tion A- 1 6 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C T able J.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 7o f1 6 Installation Informa tion A- 1 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 9.
POWER WIRIN G INSTALLA TION NOTES DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 111504 8o f1 6 Installation Informa tion A- 1 8 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C T able K.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 9o f1 6 Installation Informa tion A- 1 9 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 12. External ov ercurre nt protec tion i s not prov ided by this pro duct, bu t is requi red by codes.
POWER WIRIN G INSTALLA TION NOTES 111504 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 10 of 16 Installation Informa tion A- 2 0 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C 16.
POWER WIRIN G INSTALLA TION NOTES 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 11 of 16 Installation Informa tion A- 2 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 23. Parallel system UPM and sy stem byp ass input feeds mus t come from the same s ource.
POWER WIRIN G INSTALLA TION NOTES 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 12 of 16 Installation Informa tion A- 2 2 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C T able P.
POWER WIRIN G INSTALLA TION NOTES 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 13 of 16 Installation Informa tion A- 2 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C T able Q.
POWER WIRIN G INSTALLA TION NOTES 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 14 of 16 Installation Informa tion A- 2 4 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C T able R.
POWER WIRIN G INSTALLA TION NOTES 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 15 of 16 Installation Informa tion A- 2 5 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C T able S.
POWER WIRIN G INSTALLA TION NOTES 093004 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: B 164201535 - - - 5 UPM 2 Battery Bypass inputs t o UPMs UPM 1 Battery UPM 3 Battery UPM 4 Battery Outputs.
1o f2 CONDUI T AND WIRE E NTRY L O CA TIO NS 111504 B 164201535 - - - 6 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: REMOVE DEBRIS SHIEL D COVERING EX HAUST GRILL BEFORE OPE RATING SYSTEM. TOP ENTRY CO NDUIT LA NDING FOR AC INP UT AND OUTPUT , DC INPUT , DC CO NTROL , AND INTERF ACE C ONNECTIONS.
2o f2 CONDUI T AND WIRE E NTRY L O CA TIO NS 111504 B DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: LEFT SIDE VIEW RIGHT SIDE VIEW INTER-CABINE T WIRING ACC ESS KNOCK OUTS. REMO VE KNOCK OUTS, AS REQUIR ED, T O ROUTE WIRES BETWEE N CABINETS. INSIDE P ANE LS INTER-CABINE T WIRING ACCESS KNOCK OUTS.
1o f4 UPS POWER TERMIN AL LOCA TIONS 111504 B 164201535 - - - 7 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 208V INPUT AND 208V OUTPUT NOTE: Metal shields covering wiring terminals must be removed or opened to gain access to terminals.
2o f4 UPS POWER TERMIN AL LOCA TIONS 111504 B 164201535 - - - 7 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 208V INPUT AND 208V OUTPUT RECTIFIER INPU T TERMINAL S BYPAS S IN P U T TERMINAL S .
3o f4 UPS POWER TERMIN AL LOCA TIONS 111504 B 164201535 - - - 7 480V INPUT AND 480V OUTPUT GROUND TERM INALS WIREWA Y FOR TOP ENTRY POWER WIRING NOTE: Metal shields covering wiring terminals must be removed or opened to gain access to terminals.
4o f4 UPS POWER TERMIN AL LOCA TIONS 111504 B 164201535 - - - 7 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 480V INPUT AND 480V OUTPUT TERM INAL DET AIL AC INPUT TO U PS RECTIFIER (DUA L INPU.
1o f1 2 INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS 111504 B DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 164201535 - - - 8 Installation Informa tion A- 3 3 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 1.
X --- S L O T S STANDARD X - - - SLOT COMMUNICATION BA Y 12 3 4 OPTIONAL X - - - SLOT COMMUNICATION BA Y WIREW A Y FOR BOTTOM ENTRY IN TERF ACE WIRI NG 111504 B 164201535 - - - 8 DESCRIP TION: DA TE: .
NOTE: 1. All building ala rm inputs or remote fea tures require a n isolated normally - open contact or switch (rated at 24 Vdc, 20 mA minimum) connected between the alarm i nput and com mon term inal as shown. Al l contro l wiring and rel ay and switch contacts are customer provided.
111504 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS 4o f1 2 Installation Informa tion A- 3 6 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C 9.
111504 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS 5o f1 2 Installation Informa tion A- 3 7 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C 11.
111504 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS 6o f1 2 Installation Informa tion A- 3 8 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C 14.
111504 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS Hot Syn c CAN Bridge Card CONNECTION S FOR P ARALLEL SYSTE.
093004 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS NOTE: This drawing is for parallel wiring purposes and is not a floor layout plan. UPMs can be placed in any physical order .
Installation Informa tion A- 4 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Building Alarm Pull Chain Wiring T erminat ions From UPM 1 To U P M 2 To U P M .
Installation Informa tion A- 4 2 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C Alternate Building Alarm Pull Chain Wiring T erminations From UPM 1 To U P M 2.
111504 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS TERMINAL TB– 1 SIGNAL CONNEC TIONS FROM THE UPS GROUND T.
111504 B 164201535 - - - 8 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: INTERFACE WIRING INSTALLA TION NOTES AND TERMIN AL L OCATIONS UPS CAN CARD J3 120 VAC FROM CRITICAL BUS LINE NEUTRA L TW.
1o f4 UPS CABIN ET DIMENSION S 111504 B 164201535 - - - 9 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: RIGHT SIDE VIEW FRONT VIEW Installation Informa tion A- 4 5 Powerware ® 9390 UPS (40–8.
UPS CABIN ET DIMENSION S 111504 B 164201535 - - - 9 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: Dimensions are in millimeters [inches] 2o f4 TOP VI EW BOTTOM VIEW Installation Informa tion A-.
UPS CABIN ET DIMENSION S 111504 B 164201535 - - - 9 DESCRIP TION: DA TE: DRAWING NO : SHEET : REVISION: Dimensions are in millimeters [inches] 3o f4 BOTTOM VIEW with O PTIONAL FL OOR MOUNTING BRACKETS.
UPS CABIN ET DIMENSION S 111504 B 164201535 - - - 9 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: Dimensions are in millimeters [inches] 4o f4 BOTTOM VIEW with OPTIONAL SEISMIC MOUNTING BRACKET.
1o f1 OPTIONAL REMOTE EMERGENCY POWER -OFF 111504 B 164201535 - - - 10 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 114.3 (4.50) 115.8 (4.56) 11.9 (0.47) 95.3 (3.75) SQUARE 88.9 (3.50) 1/2 in. Knoc kout Pattern typ. 5 sides TO UPS TO OTHER EQUIPMENT NOTE: 1.
1o f1 OPTIONAL REMOTE MON ITOR P AN EL 111504 B 164201535 - - - 11 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: KNOCKOUTS PROVIDED ON FIVE SURF ACES FLUSH MOUNT USE # 10 P AN HEAD SCRE WS (MOU.
1o f2 OPTIONAL RELA Y INTERF ACE MODULE 111504 B 164201535 - - - 12 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: KNOCKOUTS PROVIDED ON FIVE SURF ACES FLUSH MOUNT USE # 10 P AN HEAD SCRE WS (MO.
OPTIONAL RELA Y INTERF ACE MODULE 111504 B DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: 164201535 - - - 12 2 of 2 15–PIN D–S UB CONNECTOR S Installation Informa tion A- 5 2 Powerware ® 93.
1o f1 OPTIONAL SU PERVISORY CON T ACT MODULE 111504 B 164201535 - - - 13 DESCRIP TION: DA TE: DRAWING NO : SH EET : REVISION: KNOCKOUTS PROVIDED ON FIVE SURF ACES FLUSH MOUNT USE # 10 P AN HEAD SCRE W.
Installation Informa tion A- 5 4 Powerware ® 9390 UPS (40–80 kVA) Installat ion and Operation Manual S 164201535 Rev C This page intentionally left blank.
W- 1 Powerware ® 9390 UPS (40–80 kVA) Installation and Operation Manual S 164201535 Rev C Warranty LIMI TED FACTORY WARRANTY FOR POWERWARE ® 9390 PRODUCTS WARRAN TOR: The warrantor for the limited warra nties set forth herein is Powerware Corporation, a Delaware Corporati on (“Powerware”).
Warranty W- 2 Powerware ® 9390 UPS ( 40–80 kVA) Installatio n and Operation Manual S 164201535 Rev C This page intentionally l eft blank..
.
*164201535C* 164201535 C.
Een belangrijk punt na aankoop van elk apparaat Powerware 9390 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Powerware 9390 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Powerware 9390 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Powerware 9390 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Powerware 9390 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Powerware 9390 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Powerware 9390 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Powerware 9390 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.