Gebruiksaanwijzing /service van het product SI-24 van de fabrikant Roland
Ga naar pagina of 52
Owner’s Manual Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” (Owner’s Manual p. 2), “USING THE UNIT SAFELY” (Owner’s Manual p. 3), and “IMPORTANT NOTES” (Owner’s Manual p. 5). These sections provide important information concerning the proper operation of the unit.
2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
3 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. .......................................................................................................... 002a • Do not open or perform any internal modifica- tions on the unit.
4 016 • Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page. ........................................................
5 IMPORTANT NOTES 291b In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2 and 3–4, please read and observe the following: Power Supp.
6 204 * Microsoft and Windows are registered trademarks of Microsoft Corporation. 206c * Windows® 98 is known officially as: “Microsoft® Windows® 98 operating system.” 206f * Windows® 2000 is known officially as: “Microsoft® Windows® 2000 operating system.
7 Contents USING THE UNIT SAFELY...................................................................................................................... 3 IMPORTANT NOTES ..................................................................................
8 Before you begin Check the contents of the package ❑ SI-24 ❑ Owner’s manual (this document) ❑ Power supply cable ❑ Pro Tools mode labels (*) Main features of the SI-24 The SI-24 supports R-BUS.
9 Panel Description Panel Description Top panel Input/output section fig.** INPUT jacks 1–8/XLR type Devices with XLR type plugs can be connected to these jacks. The audio that is input to INPUT 1–8 of the SI-24 will be sent to “R-Bus In 1–8” of the RPC-1.
10 Panel Description Control section fig.** Faders These move the on-screen faders to adjust the volume level of the channels. When you use the mouse to move the on-screen faders, the faders of the SI-24 will move in tandem. STATUS buttons STATUS MODE The function of [STATUS] will change according to the selected STATUS MODE .
11 Panel Description Panel Description EQ/SEND (Equalizer/Send) button When [EQ/SEND] is on (lit), you can use PAN knobs 1–12 to adjust the equalizer or the bus send level. For details, refer to “Controlling the equalizer” (p. 34 or “Controlling the bus send levels” (p.
12 Panel Description MARKER button When [MARKER] is on (lit), [0] will function as the Marker Request button. Markers will be registered (stored) to [1] – [9] . For details, refer to “Registering a song location—Marker Create” (p. 36). SHORTCUT button When [SHORTCUT] is on (lit), [0] – [9] will function as command execution buttons.
13 Panel Description Panel Description Panel Description Rear panel Power switch Turns the power on/off. Earth Connector Connect the ground cable here. In some cases, depending on the environment in which the unit is installed, the surface of the panel may sometimes feel rough and grainy.
14 Preparing to use the SI-24 Connecting peripheral equipment Make connections correctly, as shown in the diagram below. fig.02-** DAT Recorder, VS series, etc. DAT Recorder, VS series, etc. Audio Set etc. Power amp Mic PC To Power Outlet Stereo Headphones Keyboard etc.
15 Preparing to use the SI-24 Preparing to use the SI-24 • Do not connect plugs to both the XLR type and phone type INPUT jack of the same number. • You cannot use the GUITAR jack and the INPUT 8 jack (phone type/XLR type) simultaneously. If devices are connected to both jacks, the GUITAR jack input will take priority.
16 Preparing to use the SI-24 Turning the power on/off ■ Turning the power on 1. Use the rear panel POWER switch to turn on the power of the SI-24. When the power is turned on, the power indicator will light. 2. Turn on the power of your audio system.
17 Preparing to use the SI-24 Preparing to use the SI-24 Adjusting the input sensitivity Use the INPUT sensitivity knobs to adjust the input sensitivity. You can adjust the input sensitivity over a range from line level (+4 dB) to mic level (-50 dB). The peak indicators will light at a level below the point at which the sound distorts.
18 Preparing to use the SI-24 Using the digital input The output of a digital audio device (e.g., electronic musical instrument, DAT recorder, or the Roland VS series) connected to the SI-24 can be input to RPC-1 while still in digital form. If you want to use the DIGITAL IN input, use the following procedure to change the settings.
19 Overall signal flow Overall signal flow SI-24 OUTPUT OUTPUT OUTPUT 2 OUTPUT 1 OUTPUT 8 OUTPUT 7 RECORDER RECORDER TR 2 TR 1 TR 24 TR 23 INPUT MIXER INPUT MIXER INPUT 2 INPUT 1 Logic RPC Pro RPC-1 I.
20 Monitoring the SI-24’s inputs The SI-24 does not provide mixing functionality. For this reason, if you want to use the master output or headphones to monitor the sounds that are being sent to the SI-24’s inputs, the sounds that are being input to the SI-24 must be sent back from the computer to the SI-24.
21 Monitoring the SI-24’s inputs Monitoring the SI-24’s inputs Using the RPC-1’s mixer to return the input sound This allows latency-free monitoring (i.e., monitoring with no delay). Also, you will be able to monitor the input sound at any time, unless you change the settings.
22 Monitoring the SI-24’s inputs 8. Click the “Hardware Settings” tab. 9. ● Windows 98/ME Check “Disable audio app use of Monitor Mixer and Patchbay/Router.” fig.M05 ● Windows 2000/XP Check “Disable Control of the Monitor Mixer and Patchbay/Router by Audio Applications.
23 Monitoring the SI-24’s inputs Monitoring the SI-24’s inputs Using the RPC-1’s direct monitoring function to return the input sound This allows latency-free monitoring only for the input sounds in your application software. 1. Open the RPC-1 control panel.
24 Monitoring the SI-24’s inputs Returning the input sound from your application software This allows monitoring only for the input sounds that are set to record mode in your application software.
25 Making system settings Making system settings Making settings appropriate for your application Selecting the protocol In order to use the SI-24 to control your application, you must select the appropriate protocol. 1. Hold down [SYSTEM] and press the mode button [1] – [5] for the settings you want to use.
26 Making system settings Setting/registering user mode settings You can assign different MIDI events of your choice to the buttons and knobs of the SI-24, and register these settings to [4] (USR 1) or [5] (USR 2) . The settings you register will be remembered even when the power is turned off.
27 Making system settings Making system settings ■ Assigning MIDI events to LEDs and faders (Return) As an example, here’s how to make user mode settings for [4] (USR 1) . 1. Hold down [SYSTEM] and press [4] (USR 1) to select the button for which you want to register settings.
28 Making system settings Saving user mode settings on your computer—Dump You can save user mode settings on your computer or sequencer. This provides a convenient way to back up the settings you register to [4] (USR 1) or [5] (USR 2) , or allows you to prepare several sets of user mode settings.
29 Making system settings Making system settings Using the MIDI connectors to transmit/receive control data—MIDI Control Mode With the factory settings, the SI-24 will transmit and receive control data via R-BUS.
30 Making system settings Outputting the RPC-1’s R-Bus Out 7/8 from the SI-24 With the factory settings, the RPC-1’s “R-Bus Out 7/8” will not be output from the SI-24. If you want “R-Bus Out 7/8” to be output from the SI-24, change the setting as follows.
31 Controlling Logic RPC Pro Controlling Logic RPC Pro You can remotely control Logic RPC Pro from the SI-24. * The software upgrade of Logic RPC Pro may make the operation process different or may include additional functions. Making the SI-24 settings Use the following procedure to switch the settings of the SI-24.
32 Controlling Logic RPC Pro Selecting channels 1. Use CH ASSIGN to select the Logic RPC Pro mixer section that you want to control. The selected button will light. [INPUT/INST] : Select this when you want to control INPUT. If you want to control instruments, hold down [SHIFT] and press [INPUT/INST] .
33 Controlling Logic RPC Pro Controlling Logic RPC Pro Switching the status of a channel The function of [STATUS] will change depending on the STATUS MODE . 1. As described in the preceding section “Selecting channels,” select the Logic RPC Pro mixer section that you want to control.
34 Controlling Logic RPC Pro Controlling the equalizer The buttons and knobs of the SI-24 correspond to the Logic RPC Pro equalizer parameters as follows.
35 Controlling Logic RPC Pro Controlling Logic RPC Pro Controlling the bus send levels The send levels to four buses can be controlled from the SI-24. PAN knobs 9–12 will control the send levels to the buses. Knob 9 ➔ SEND 1 Knob 10 ➔ SEND 2 Knob 11 ➔ SEND 3 Knob 12 ➔ SEND 4 Use the following procedure to control the send levels.
36 Controlling Logic RPC Pro Registering a song location—Marker Create Logic RPC Pro has a Marker Create function that lets you assign a marker at the desired location in a song. Here’s how to control Logic RPC Pro’s Marker Create function from the SI-24.
37 Controlling Logic RPC Pro Controlling Logic RPC Pro Recalling screens assigned to the numeric keys —Screen Sets Logic RPC Pro lets you register various configurations of windows (“screen sets”) to numeric keys 1–9 of the keyboard, and recall these screen sets by pressing a numeric key.
38 Controlling Pro Tools (version 4.1 or later) Digidesign Pro Tools can be remotely controlled from the SI-24. ■ Putting Pro Tools mode labels When controlling Pro Tools, the button and knob functions will differ in some ways from the panel.
39 Controlling Pro Tools (version 4.1 or later) Controlling Pro Tools Making Pro Tools settings Use the following procedure to make settings in Pro Tools. 1. Start up Pro Tools. 2. From the Setups menu, choose Peripherals. The Peripherals window will open.
40 Controlling Pro Tools (version 4.1 or later) How the SI-24’s controls will function The explanation in this section will use the button names corresponding to the included Pro Tools mode labels. ■ Faders 1–8 These control the faders of the area enclosed in blue within the Pro Tools Mix window.
41 Controlling Pro Tools (version 4.1 or later) Controlling Pro Tools ■ EQ/SEND (Equalizer/Send) buttons You can press [EQ/SEND] to turn it on (lit), and use SEND 1–4 (PAN 9–12) to control the send levels of the channel you selected in [CH SELECT] .
42 Controlling Cubase VST (version 5.0 or later) The SI-24 can remotely control Steinberg Corporation’s Cubase series programs. Cautions when controlling Cubase ● When the selected protocol (p. 25) is “Cubase mode,” the following buttons and knobs cannot be used.
43 Controlling Cubase VST (version 5.0 or later) Controlling Cubase VST Making Cubase settings Use the following procedure to make Cubase settings. 1. Start up Cubase. 2. From Remote Setup on the Option menu, choose Setup. The VST Remote window will appear.
44 Controlling Cubase VST (version 5.0 or later) How the SI-24 controls will function ■ Faders 1–12 These will control the Cubase faders. The CH ASSIGN (Channel Assign) settings correspond as follows to the faders that will be controlled.
45 Controlling Cubase VST (version 5.0 or later) Controlling Cubase VST ■ MARKER button When you press [MARKER] to turn it on (lit), the [0] – [9] buttons will function as locator buttons.
46 Glossary Condenser microphone A type of microphone that applies the principle of a condenser. It has excellent high-frequency response, and allows more subtle nuances of sound to be captured. This type of microphone requires external, phantom power unless it has its own battery power.
47 Block Diagram Block Diagram GAIN PHANT OM PEAK TRS XLR GUIT AR INPUT 8 ONL Y ANALOG INPUT 1 - 8 to AD DIGIT AL IN ON ON 7/8 D .OUT OUT 1/2 OUT 3/4 OUT 5/6 OUT 7/8 R-BUS MIDI IN MIDI OUT IN 1/2 IN 3.
48 Specifications SI-24: SUDIO INTERFACE ■ Sample Rate 22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz ■ Frequency Response 96 kHz: 0 Hz–40 kHz (+0/-3 dB) 48 kHz: 20 Hz–22 kHz (+0/-3 dB) 44.
49 ...MEMO....
Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. As of December 1, 2002 (Roland) ARGENTINA Instrumentos Musicales S.
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For EU Countries For Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
03010945 ’03-1-A2-41KS 984 *A separate publication titled “MIDI Implementation” is also available. It provides complete details concerning the way MIDI has been implemented on this unit.
Een belangrijk punt na aankoop van elk apparaat Roland SI-24 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Roland SI-24 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Roland SI-24 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Roland SI-24 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Roland SI-24 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Roland SI-24 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Roland SI-24 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Roland SI-24 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
