Gebruiksaanwijzing /service van het product BGH827 van de fabrikant Ryobi
Ga naar pagina of 18
SA VE THIS MANUAL FOR FUTURE REFERENCE Y our bench grinder has been engineered and manufactured to Ryobi’ s high standard for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance.
2 T ABLE OF CONTENTS n T able of Contents ............................................................................................................................................................ 2 n Introduction ...................................
3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failur e to follow all instructions listed below , may r esult in electric shock, fire and/or serious personal injury . READ ALL INSTRUCTIONS n KNOW YOUR POWER TOOL. Read the operator’ s manual carefully .
4 n INSPECT TOOL CORDS PERIODICALL Y . I f d am- aged, have repaired by a qualified service technician at an auth orize d servi ce faci lit y . The co ndu cto r with insu latio n having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor .
5 n NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the grinding path of the wheel. n A VOID AWKW ARD OPERA TIONS AND HAND POSI- TIONS where a sudden slip could cause your hand to move into the wheel. AL WA YS make sure you have good balance.
6 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Pr oper interpreta- tion of these symbols will allow you to operate the tool better and safer .
7 SYMBOLS SERVICE Servicing requir es extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts.
8 SPEED AND WIRING The no-load speed of this tool is approximately 3,600 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’ s horsepower rating. A line intended only for lights cannot pr operly carry a power tool motor .
9 FEA TURES PRODUCT SPECIFICA TIONS- MODEL BGH616 Wheel Diameter ........................................................... 6 in. Wheel Thickness ...................................................... 3/4 in. Arbor Hole ..............................
10 ADJUST ABLE WRENCH Fig. 3 COMBINA TION WRENCH (3) 7 mm, 10 mm, and 12 mm PHILLIPS SCREWDRIVER The following tools (not included) are needed for checking adjustments of your saw or for installing the blade: TOOLS NEEDED LOOSE P AR TS The following items are included with your Bench Grinder: n Shield Bracket – one left, one right .
11 MOUNTING SAFETY SHIELD ASSEMBL Y See Figure 5. n Fasten the safety shield assemblies to the safety shield brackets using the fastening knob and small washer . NOTE: The slotted part of the safety shield bracket must face towards the grinding wheel guar d.
12 WASHER CARRIAGE BOL T WORK REST ASEMBL Y Fig. 6 KNO B PIN ASSEMBL Y MOUNTING WORK REST See Figure 6. n Remove the knob, star washer , and washer from the car - riage bolt on the lower portion of wheel guard.
13 WARNING: Do not allow familiarity with tools to make you car e- less. Remember that a careless fraction of a second is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools.
14 OPERA TION Fig. 10 SCREWDRIVER VISE LA WN MOWER BLADE SHARPENING TWIST DRILL BITS See Figure 9. Drill bits are best sharpened on a sharpening jig (available at most hardware stores). Begin on one side of the point at the existing angle, then twist the bit while maintaining contact with the grinding surface.
15 Fig. 12 SCREW(S) GRINDING WHEEL OUTER FLANGE INNER FLANGE LOCK WASHER(S) HEX NUT(S) WHEEL GUARD COVER WHEEL NUT SPINDLE SHAFT WARNING: Always disconnect the bench grinder from the power source before performing any assembly or adjustment. Failure to do so could result in accidental starting resulting in possible serious personal injury .
16 MAINTENANCE Ele ctric tool s use d on fibe r glas s mater ial, wal lbo ard , spa cklin g compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commu- tator s, etc.
17 NOTES.
R YOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www .ryobitools.com 983000-626 3-05 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center .
Een belangrijk punt na aankoop van elk apparaat Ryobi BGH827 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ryobi BGH827 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ryobi BGH827 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ryobi BGH827 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ryobi BGH827 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ryobi BGH827 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ryobi BGH827 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ryobi BGH827 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
