Gebruiksaanwijzing /service van het product AS-2775 van de fabrikant Autostart
Ga naar pagina of 34
Notice The manufactur er will accept no responsibility fo r any electrica l damage resulting from improper in stallation of the product, b e that either damage to the vehicl e itself or to t he unit. This uni t must be installed by a certified tech nician using a ll safety devices s up plied .
P. 2 Installation Guide Table of Contents Introducti on ............................................................ 2 Included in the Kit .................................................. 3 Installati on Tools .......................................
Installation Guide P. 3 Included in the Kit Before beginning the installation, pleas e review the Installation Guide —particularly the Wiring Diagram and the Programming Options.
P. 4 Installation Guide ♦ When wiring in parall el, make sure to isolate each c onnection with a diode in order to avoid feed back and pos sible damage.
Installation Guide P. 5 Installation Order The following is a suggested order for the Installation pr ocedure. It is intended as a guide f or novices, to hel p make the pr ocess of insta lling a remote s tarter module eas ier. Time is wasted by rewiring the module whe n mistakes are mad e.
P. 6 Installation Guide when the module i s in the vehicl e. The fuses on t he power wires shou ld be removed d uring the pre-wire stage. The fus es will not be put back in unt il the powerin g stage of the i nstallation. − Once the pre-wiring is finis hed, the module c an be brought int o the vehicle.
Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or v oltage change by activating sw itches or other devices in an electric circ uit. An electroma gnetic switch, remot e-controlled switc h, a switc hing device.
P. 8 Installation Guide quenching/sup pression diode, and t hat the Negative trigg er is on the same terminal of the relay as the Anode (+ or no n-striped side) of the quenchin g/ suppression diode. When a relay’s coil is energiz ed, a magnetic fie ld is created and e nergy is stored in the coil .
Installation Guide P. 9 Problem: Some vehicle circuits nee d to be isolate d from feedback . In some cas es, when a vehicl e is remote started , feedback oc curs on a circu it and powers anot her device or sw itch that was not intended to be p owered during t he remote starts.
P. 10 Installation Guide the relay is act ivated, +12 vol ts from 87 is sent t hrough 30, and t he OEM trunk sw itch is activated, by the positiv e pulse. Interruption: Example : Creating a St arter Kill relay to prevent unauthoriz ed starting of the vehicle.
Installation Guide P. 11 module's Trunk rel ease output activa tes the relay. The ground sign al is sent from 87 through 30 t o the vehicle's Trunk release wire ac tivating the switc h and opening the trunk. Harness Description 6-pin Mai n Ignition Ha rness (a.
P. 12 Installation Guide 5-pin Secondary Ha rness (a.k.a. the secondary harn ess) This harness has the remaining wires used in basic remote s tarter inst allations, pos itive parking light output, the safety shut down in puts, and the ground wire for the module.
Installation Guide P. 13 6 VIOLET (+) Door pin input This input should be used in vehicles that use a posi tive-switching Dome Light circuit. Connect to a Door trigger wire testing +12 V with a Door open. CAUTION! You can only use a negative or a positive c onnection.
P. 14 Installation Guide (Also known as the “wait-to-start light”.) T he purpose of the Glow-plug circuit on diesel vehicles is to pre-heat the Combustion Chamber before the vehicle is started.
Installation Guide P. 15 compatibility and fun ctionalities) . 5 Pager Port Is used t o connect an optional AS-200P pager (t o use this op tion, make sure to program pager option in Menu 3, Feature 5, Option 4 ). Entering Programming Mode This allows th e installer to p rogram the unit.
P. 16 Installation Guide Manual or Automatic Transmission This module may be ins talled on vehic les with manual or aut omatic transmiss ions. It is origin ally configured for m anual transmis sions . If the vehicle you are working on is automatic, it is mandatory to make a few quic k and easy modi fications before t he unit is conn ected.
Installation Guide P. 17 2. Before the lights go out, press and hold the brake p edal and then pre ss one of the foll owing buttons: LOCK ............................... to access menu 1; UNLOCK ........................... to access menu 2; TRUNK …………………… to access menu 3; or START .
P. 18 Installation Guide OPTION 2* Ignition valet ENABLED MENU 3 * INDICATES DE FAULT SETTI NG FEATURE 1 – Home Valet OPTION 1 Home val et ENABLED OPTION 2* Home valet DISABLED FEATURE 2 – AUX 1 Programming OPTION 1 Horn confirmation upon t he 2 nd press of the LOCK button.
Installation Guide P. 19 Multi-speed Tach Programming 1. Enter programming mode (see o n page 15) the park ing lights w ill stay on for up to 20 seconds. 2. Before the lig hts go out, press and hold the brake p edal and press the LOCK and UNLOCK buttons simult aneously the park ing lights will flas h 4 times.
P. 20 Installation Guide Clutch Bypass In order to rem ote start a manual transm ission vehicl e, the clutch swi tch must be bypasse d. Clutch safety switch c ircuits can take many forms. Lis ted below are th e most comm on ones. Some vehicles may also have a separate or c ombined switch on the cl utch pedal for cruis e control.
Installation Guid e P. 21 modules connecte d to the G.O. Wire, a relay (and d iodes) may have to be add ed to strengthen t he negative current going to the clutc h bypass. Positive: Very similar to the n egative system, e xcept that the ve hicle's clut ch relay is trigge red by 12 volts instead of a negative signal.
P. 22 Installation Guide ¾ Standard Secure Lock: If this Option is selected, upo n receiving a remote START signal, secure lock will unlock th e doors (disarming the fa ctory Alarm); 1/2 s econd after the remot e start, it will relo ck t he doors. Four seconds after shut down, secure lock will relock all doors ( arming the system once ag ain).
Installation Guid e P. 23 Flashing LED To gain access to this feature, make s ure the Flashing LED option h as been enabled a t the time of programming. Onc e this option is enabled, t he user has the choice to t oggle the Flas hing LED ON and OFF at any giv en moment.
P. 24 Installation Guide If the vehicle has a manual transmission , Idl e Mode can be ac tivated through the same routine as that used for Ready Mod e (see “Ready Mode Option” in this Guide) ; at the last step, t he TRUNK button is press ed instead of the o ther buttons .
Installation Guid e P. 25 If Safe Start is enabled , you can activate Cold W eather Mode by: • Pressing and rele asing the START butto n, then; • Pressing and hol ding the START button u ntil the parkin g lights flash 3 times .
P. 26 Installation Guide • To put the system o u t o f Valet mode using the TRANSMITTER (Remote Valet Mode): a. Press the UNLOCK and START butt ons simultane ously until the parking lights flash twice. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode.
Installation Guid e P. 27 transmitter, and to unlock the other doors , if desired, by pres sing the UNLOCK button for a second time. The output will prov ide a 1-second negative output w hen the UNLOCK button is pres sed a second time on the trans mitter.
P. 28 Installation Guide To set the syste m to Ready Mode: If Ready Mode is enable d by remote If Ready Mode is enabled by handbrake 1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the neutral position. 2.
Installation Guid e P. 29 5. To save the new settings: pr ess LOCK and UNLOCK . If 3 chirps ar e returned, the new settings have been sav ed Resetting the module to default features Resetting the mo dule is not a required process. Mos t of the time, y ou can avoid res etting the module by fixi ng the issue direc tly at the r oot of the ca use.
P. 30 Installation Guide Starter kill option. Sit ins ide the veh icle with all doors closed. Arm th e vehicle, t hen try to start the engine with the key . The engine should not start. If the engine s tarts, rewire the starter kill to reach proper oper ation.
Installation Guid e P. 31 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed. • Run time has expired. • TRUNK button pressed. • Start signal received by the module. • Cold weather mode cancelled.
P. 32 Installation Guide Troubleshooting Q & A The following ar e some common ins tallation-relate d issues. A problem or symptom is given and then possible solut ions and/or sugge stions as to areas to verify are enumerated. 1. I cannot program the remote control.
Installation Guid e P. 33 • Do you have the co rrect OEM disarm wire? • Did you program t he disarm wire? 11. The ABS and the CHECK ENGINE light come on in the dash. • Are you missing a second ignit ion or access ory? 12. The car starts and runs but t he heater blower motor does n ot work.
P. 34 Installation Guide 25. I blow fuses ever y time I try the remote door loc ks and I have alr eady installed a r elay. • Door locks are reverse p olarity, and not positive trigger. 26. I blow fuses every time I try the remote trunk rel ease and I have already installed a relay.
Een belangrijk punt na aankoop van elk apparaat Autostart AS-2775 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Autostart AS-2775 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Autostart AS-2775 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Autostart AS-2775 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Autostart AS-2775 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Autostart AS-2775 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Autostart AS-2775 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Autostart AS-2775 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
