Gebruiksaanwijzing /service van het product HT300 Link van de fabrikant Sim2
Ga naar pagina of 39
User and Installation Manual The home theater projector HT300 LINK cod.46.0327.300.
LIGHT F1 ZOOM FOCUS F2 Not active in this model. MENU - Activates the On Screen Display menus. Navigates menu pages. FREEZE Freezes a moving picture. STAND-BY Switches off to stand-by. 0-9 Keys Switch on from stand-by and allow direct source selection.
1 1 INTRODUCTION Congratulations on your choice of the SIM2 Grand Cinema HT300 LINK system! 1 2 DIGIOPTIC ™ L I NK C L ASS 1 L ASER P R ODUCT 3 - O N DIGIOPTIC ™ I M A G E P R OC ES S O R O F F.
2 All image adjustments can be perfor med with the remote contr ol with the aid of the On Screen Display; alternatively , the unit can be controlled by fr om a home automation system through the serial port.
3 Prior to switching on the pr ojector please read each chapter of this manual carefully as this manual pr ovides basic instructions for using the projector . The installation of the lamp assembly , preliminary adjustments and procedur es that necessitate the removal of the top cover , must be carried out by authorised, trained technicians.
4 12 11 13 15 10 14 1 2 CLASS 1 LASER PRODUCT 3 - 6 4 1 2 3 9 5 8 7 1 2 D IGI O P T I C “ L I N K C L A S S 1 L A S ER P R O D U C T 3 - 1 Projection lens 2 Lens shift knob 3 Cooling air inlet vents.
5 • Read this manual carefully and keep it in a safe place for future consultation. This manual contains important infor mation on how to install and use this equipment corr ectly . Before using the equipment, read the safety pr escriptions and instructions carefully .
6 3 UNP A CKING T o unpack the projector safely and easily please follow steps 1 to 6, as per drawing (Fig. 4). It is recommended that the carton and packaging is r etained for future use and in the unlikely event that your projector needs to be returned for repair .
7 The carton should contain the following: - the projector - the DigiOptic ™ Image Processor - the remote contr ol - four 1.5V AAA batteries (for remote contr ol) - DigiOptic ™ Image Processor pow.
8 Protective cap Separation point Cable Fibre Connector Ferrule CAUTION: In the case of ceiling or wall mounting using a suspension bracket, follow the instructions carefully and comply with the safety standards you will find in the box together with the bracket.
9 T o activate an electric motorised screen a 12 V olt output is provided at the r ear of the DigiOptic ™ Image Processor . This can be connected to a screen interface unit, which can be supplied by screen manufactur ers (Fig.
10 T able 1 shows the types of signals usually available for the most common types of video sources and the corr esponding input connectors to use on the DigiOptic ™ Image Processor) .
11 RGB GRAPHICS This input should be connected to an RGB-type video or graphic signal using a cable with a DB15HD type connector . The signal source de vice (typically a personal computer or game console) must be ab le to provide separate H/V synchronisation or composite H+V .
12 HDMI Fig.12.
13 The HT3 00 LI NK system consists of the Pr ojector and the DigiOptic ™ Image Pr ocessor (which is also the system control centre). The DigiOptic ™ Image Processor sends commands to the Projector and r eceives operating status information from the Projector and function commands fr om the user .
14 R C I 2 00 5 LI GH T 0 T ypically , the picture will appear after 15-20 seconds. Pressing a key from 1-9 on the r emote control selects the corr esponding input; pressing 0 selects the input active at the time the system was last switched off.
15 + - + - + - + - Four 1.5V AAA type batteries 7 REMO TE CONTROL The remote contr ol transmits commands to the system by infrared signals. There ar e three infrar ed sensors, one at the front of the Pr ojector , one at the rear of the Pr ojector and one on the front panel of the DigiOptic ™ Image Processor .
16 Inputs 1 VIDEO 1 2 VIDEO 2 3 S-VIDEO 3 4 S-VIDEO 4 5 COMP/RGB 5 6 COMP/RGB 6 7 COMP/RGB 7 8 COMP/RGB 8 9 GRAPH RGB 9 10 GRAPH RG B 1 0 11 DVI-D 1 1 12 HDMI 12 1 2 3 4 5 YCrCb 32kHz 6 RGBS 15kHz 7 Y.
17 Picture Contrast Colour Tint Sharpness Filter Cinema Mode Video T ype 50 50 50 3 2 Off Normal Auto Auto VCR1 VCR2 Noise Reduction Brightness 60 The various menus only offer the r elevant adjustments in accordance with the type of input signal displayed (e.
18 the picture colour intensity . When set to zero, colour images will be shown in black and white. Increasing the value, try to find the point at which the colours look natural: suitable refer ences include skin tones and grass in landscape shots. TINT Controls the purity of the colours.
19 IMAGE This menu features adjustments r elating to picture position, aspect ratio, etc. ASPECT This adjustment allows you to change the dimensions and aspect ratio (relationship between width and height) of the displayed image. There ar e five preset aspects available and three personalised aspects (with user -settable parameters).
20 the system checks the input signal and automatically sets the most suitable values. However , if the image is not perfectly centralised it may prove useful to request the system to r epeat the input signal analysis and image positioning, calling the automatic control pr ocedu- re fr om the AUTO button on the remote contr ol or keypad.
21 Adjust the feet underneath to obtain a level position, lining up the base of the projected image to the base of the pr ojection screen (Fig. 22) . 1 2 C L A S S 1 L AS E R PR O D U C T 3 - Fig.
22 F ACTORY DEF AUL TS Reconfigures the pr ojector to original factory settings except Position, Orientation, Y/C Delay , Zoom and Focus. No Confirm? Ye s MENU LANGUAGE Lists the languages available for the On Screen Display menus.
23 F1/F2 KEYS This allows to assign differ ent functions to the remote control keys, named F1 and F2. The window is made of 6 options, once for each line and by two columns showing the F1-F2 keys. The choice between F1 and F2 is made by the and keys of the remote contr ol; the function given to F1 and F2 is chosen with the and keys.
24 MEMORIES The main parameters of the image may be saved in distinct groups of values (known as ‘ Memories ’ ); these parameters can subsequently be applied all together by way of a single com- mand.
25 SA VE DEFAUL T SETTINGS T o restore the original values to a pr eviously modified Memor y , select the line corresponding to the Memory in question and open the pull-down menu ( key). Then select the line ‘ Initial settings saved in Memory 1 ’ .
26 10 TR OUBLESHOO TING GUIDE No power (Green and red LED are OFF) - Check the power switch at the rear: it must be in position I . - Check if the power cable has been connected correctly to a working socket. - Check the power socket fuse, at the rear of the pr ojector .
27 by selecting POSITION on the IMAGE ADJUSTMENTS menu. - Adjust the width and height of image, selecting ASPECT in the IMAGE ADJUSTMENTS menu. - Adjust the Overscan value in the IMAGE/OVERSCAN menu. Image too dark, too pale or unnaturally coloured - V erify compatibility of video/graphic signals with technical specifications of your projector .
28 PROJECTOR OPTICAL Projection system: optical engine based on 1 DMD ™ HD2+ chip, sealed housing, dusty proof DMD ™ panel: resolution 1280x720 pixel Brightness uniformity: 10% above or below the .
29 DIGIOPTIC™ IMAGE PROCESSOR ELECTRICAL Input signals: • 2 COMPOSITE VIDEO (CVBS) RCA type connectors, gold-plated 1.0 V pp / 75 Ω , negative synchronisation • 2 S-VIDEO (Y/C) 4-pin mini-DIN connectors Y : 1.0 V pp / 75 Ω , negative synchronisation C: 0.
30 B DIMENSIONS PROJECT OR DIGIOPTIC ™ IMA GE PROCESSOR unit: mm (inches) unit: mm (inches) 74 (2- 15/16 ) 352 (13- 7/8 ) 174 (6- 7/8 ) 102 (4) 318 (12- 1/2 ) 440 (17,32") 289 (11,38") 57 .
31 C PROJECTION DIST ANCES Follow the table below to determine the optimal projection distance “ L ” between the scr een and the center of the lens (fFig 30a).
32 Screen Scr een size width (diagonal) min. L H max max. L H max Min projection distance 4/3 3,4 11 ’ 0 ” 4,0 13 ’ 2 ” 4,7 15 ’ 7 ” 5,4 17 ’ 7 ” 6,0 19 ’ 9 ” 6,7 22 ’ 0 ” 8,0 .
33 D ON SCREEN MENU LA Y OUT Brightness Contrast Color Tint Shar pness Filter Cinema Mode Video T ype Video • S-Video [NTSC] YCrCb15kHz RGBS 15kHz RGBS RGB Grafico DV I - D HDMI ™ Film Video Graph.
34 Orientation K eystone Lens P ower ON T est patter ns Initial settings Floor Floor-rear Ceiling Ceiling-rear Setup Horizontal Horizontal Zoom F ocus Au to Stand-by Language Source list F1/F2 ke ys S.
35 Memories Cancel Confirm Edit memory name ()?@ 1 ABC 2 DEF 3 GHI 4 JKL 5 MNO 6 PQRS 7 - + TUV 8 0 WXYZ 9 _ _ _ _ _ _ _ _ _ _ _ 0 A uto 3 S MEMORY 3 Memories 2 S MEMORY 2 1 S MEMORY 1 Sav e current s.
36 INDEX 1 INTRODUCTION 1 2 IMPORT ANT SAFETY INSTRUCTIONS 3 3 UNP A CKING 6 P ackage contents 7 4 INST ALLA TION 7 P ositioning the two units 7 Connecting the two units 8 Connecting the video sources.
37 • Due to the constant product development, specifications and design might be subject to change without notice. SIM2 Multimedia S.p.a. • Viale Lino Zanussi, 11 • 33170 Pordenone - IT AL Y Phone +39.434.383.253-256 • Fax +39.434.383260-261 www .
Een belangrijk punt na aankoop van elk apparaat Sim2 HT300 Link (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sim2 HT300 Link heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sim2 HT300 Link vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sim2 HT300 Link leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sim2 HT300 Link krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sim2 HT300 Link bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sim2 HT300 Link kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sim2 HT300 Link . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
