Gebruiksaanwijzing /service van het product airPoint Pro Series van de fabrikant SmartBridges
Ga naar pagina of 28
s m a r t Bridges to the future ... Revision 1.8 Page 1 of 28 airPoint-PRO Series Wireless Access Point Quick Install Guide Installing the airPoint-PRO Series airPoint-PRO is a wireless Access Point to provide WLAN connectivity to any PC. It operates at 2.
Revision 1.8 Page 2 of 28 Contents of Pac kage airPoint-PRO Outdoor l airPoint-PRO Outdoor Unit l powerShot l AC Adapter l Pole Mounting Kit : U Bracket, Nuts, W ashers l W all Mounting Kit : W all pl.
s m a r t Bridges to the future ... Revision 1.8 Page 3 of 28 for airPoint-PRO Outdoor / airPoint-PRO TOT AL Important note - Earthing Requirements: Follow National Electric Code NEC 810-20 and NEC 810-21 for this installation. Mounting the airPoint-PRO Outdoor Fix the airPoint-PRO Outdoor unit with the U bolts to the steel pipe.
Revision 1.8 Page 4 of 28 Outdoor air Point PRO Antenna airPoint-PRO Outdoor AC/DC Adapter RJ-45 Ethernet Port 1.5 Inch pipe powerShot RF Cable Ethernet Cable U-bolt.
s m a r t Bridges to the future ... Revision 1.8 Page 5 of 28 Mounting the Antenna: Follow the mounting instructions provided by the antenna manufacturer and mount the antenna on the steel pipe. Antenna should be mounted on the same pipe as the airPoint-PRO Outdoor and positioned above it.
Revision 1.8 Page 6 of 28 Mounting the airPoint-PRO TOT AL Attach the mounting arm of the airPoint-PRO T OT AL unit with the 2pcs of U bolts to the pipe. Make sure to tighten both top and bottom U bolts, with nuts and spring washers. T ighten the nuts so that the mounting arm does not rotate on the pipe.
s m a r t Bridges to the future ... Revision 1.8 Page 7 of 28 U-bolt fixing pipe to Mounting Arm Mounting Arm airPoint-PRO T OT AL RJ45 Cable Cable Tie Wea ther proof Connector.
Revision 1.8 Page 8 of 28 to airPoin t-PRO / airPoint-PRO Outdoor / airPoint-PRO T O T AL RJ45 to Network / PC AC Adapter powerShot RJ45 Cable Cross Coupler switch SB2820 Cross Coupler switch Restore Default button Note: Restore Default button at the bottom side of the powerShot should be used to restore the device back to factory / WISP defaults.
s m a r t Bridges to the future ... Revision 1.8 Page 9 of 28 Connecting the airPoint-PRO series using Power Over Ethernet: The airPoint-PRO series is powered through the ethernet cable itself. This mode of operation gives flexibility for the user to position the airPoint-PRO at any location for best radio coverage.
Revision 1.8 Page 10 of 28 Software Installation System Requirements : Computer with Windows 98/ME/NT/2000/XP with working network card Installing airPoint-PRO Setup Software : Please insert the Setup Software CD into the CD-ROM drive of your PC. The CD will run automatically .
s m a r t Bridges to the future ... Revision 1.8 Page 1 1 of 28 Configuring the airPoint-PRO For Windows 98 / ME / NT / 2000 / XP The factory default parameters for airPoint-PRO l DHCP Client : Enabled (IP will be acquired from the DHCP Server on the LAN.
Revision 1.8 Page 12 of 28 b) Configuring airPoint-PRO using a standalone PC Connect the airPoint-PRO to the PC using cross CA T5 cable. Y ou can convert straight cable to cross using a cross connector provided. Make sure the power to the airPoint-PRO is ON.
s m a r t Bridges to the future ... Revision 1.8 Page 13 of 28 2. SETTING THE OPERA TIONAL MODE OF AIRPOINT -PRO The airPoint-PRO can operate in four different Modes, namely l Access Point - In this mode the airPoint-PRO is operating as a normal 802.1 1b compliant Access Point.
Revision 1.8 Page 14 of 28 1. Point to Point - This mode lets one airPoint-PRO talk to another airPoint-PRO wirelessly linking two Ethernet LANs behind together . 2. Point to MultiPoint - This mode lets multiple airPoint-PRO linking multiple Ethernet LANs.
s m a r t Bridges to the future ... Revision 1.8 Page 15 of 28.
Revision 1.8 Page 16 of 28 4. SECURITY T AB The airPoint-PRO can operate in four different Modes, namely l By default encryption is disabled which means the communication is not secure. In case you want to have a secure communication, ensure that the WEP encryption keys are set.
s m a r t Bridges to the future ... Revision 1.8 Page 17 of 28 Note: For WEP encryption the default format is HEX format. Incase of any wireless clients using the ASCII keys for the WEP , use the ASCII to HEX converter table for same. See Appendix B. Note: The Authentication type must be the same on the Clients and on the airPoint-PRO.
Revision 1.8 Page 18 of 28 The RSSI values are shown in dBm in ClientInfo and Associated AP Info T ab as per the internal formula. If you want your specific values to be shown in there, please store them in the table and set the option as "User Defined" from the Advanced T AB.
s m a r t Bridges to the future ... Revision 1.8 Page 19 of 28 The following information about all the associated clients is available in real time; the values are refreshed after every 5 seconds.
s m a r t Bridges to the future ... Revision 1.8 Page 20 of 28 Note: Client to Client communication T AB is disabled in the repeater mode If the client gets disassociated from the airPoint-PRO due to any reason ( power down etc ) you will continue to see the entry in the list for upto 5 minutes, before it is removed from the list.
Revision 1.8 Page 21 of 28 External Radius Server Authorization T o authorize clients using the External Radius Server please key in the following parameters and Click on Set Parameters button. l Source Port (Default Port is 1812) l Destination Port (supported in F/W 1.
Revision 1.8 Page 22 of 28 Configuring the airPoint-PRO in Client Bridge Mode In this mode the airPoint-PRO is operating as ethernet client, and it can associate only with another airPoint-PRO operating as an access point. In this Mode Site Survey and Link Status Tabs of simpleMonitor will be enabled.
s m a r t Bridges to the future ... Revision 1.8 Page 23 of 28 Configuring the airPoint-PRO in Wireless Bridge Mode In this mode airPoint-PRO can bridge 2 or more LANs wirelessly . Please select the Wireless Bridge T ab of simpleMonitor for configuring the airPoint-PRO in Wireless Bridge Mode.
Revision 1.8 Page 24 of 28 1. Point to Point This mode lets one airPoint-PRO talk to another airPoint-PRO wirelessly linking two Ethernet LANs together . A feature in this mode is that each airPoint-PRO must specify the MAC address of the airPoint-PRO at the opposite end of the wireless bridge.
s m a r t Bridges to the future ... Revision 1.8 Page 25 of 28 Repeater in Access Point Role The operation will be exactly same as Access Point serving the local clients, Access Point Mode information is equally applicable in this role. Please refer to Access Point Configuration details in Access Point Mode Section.
Revision 1.8 Page 26 of 28 5. Dial a Power Changing the output Power of airPoint-PRO Select Dial a Power T ab of simpleMonitor to change the output power of airPoint-PRO. This feature of airPoint-PRO allows the user to control the radio transmit power of the airPoint- PRO from the SimpleMonitor software.
s m a r t Bridges to the future ... Revision 1.8 Page 27 of 28 Restore Factory Default Settings If you forget the critical settings like WEP or Administrator Password of the airPoint-PRO, you can restore the airPoint-PRO to the Factory Default Settings as, 1.
Revision 1.8 Page 28 of 28 Appendix B ASCII to Hexadecimal Conversion T able Operating T emperature Range airPoint-PRO : 0 °C ~ +50 °C (+32 °F ~ +122 °F) airPoint-PRO Outdoor / T OT AL : -40 °C ~.
Een belangrijk punt na aankoop van elk apparaat SmartBridges airPoint Pro Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen SmartBridges airPoint Pro Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens SmartBridges airPoint Pro Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding SmartBridges airPoint Pro Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over SmartBridges airPoint Pro Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van SmartBridges airPoint Pro Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de SmartBridges airPoint Pro Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met SmartBridges airPoint Pro Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
