Gebruiksaanwijzing /service van het product 5/14 SERIES van de fabrikant Snapper
Ga naar pagina of 28
OPERA T OR’S MANU AL 5/14 Series Mfg. No. Description 85637 Model SAC55140BV, 5HP & 5.5HP Snapper Chipper Shredder 1692203 Model 5/14, 5HP Simplicity Chipper Shredder 1692352 Model 5/14, 5HP Simplicity Chipper Shredder (CE) 1692722 Model 5/14, 5HP Simplicity Chipper Shredder (CE) 1694897 Model 5/14, 5.
2 Not for Reproduction.
3 T able Of Contents MODEL IDENTIFICA TION ........................................3 SAFETY RULES General ...............................................................4 Setting Up ...........................................................4 Operating Location .
DANGER You must read and understand this manual and all safety instructions and labeling completely, before attempting to assemble, set-up, trans- port, operate, service, or install any options or accessories on this unit.
DANGER SPARK/FIRE HAZARD GAS ENGINES MAY REQUIRE A SPARK ARRESTER FOR SAFE OPERATION If the engine on this unit is not equipped with a spark arrester and is to be used on any forest, brush, or grass-covered unimproved land, a spark arrester must be added to the muffler before using the engine on such land.
6 Safety Rules OPERA TING SAFETY 1. Always obey the size limitations for tree limbs and branches stated in the Waste Materials Guide portion of this manual. 2. Never leave the machine running unattended. Always turn off the engine, wait for the rotor to come to a complete stop, and disconnect the spark plug before leaving the area.
fuel leakage, and unwanted transfer of the sump oil into the cylinder head area. 3. Always refill the oil sump with the recommended oil before attempting to use the unit again after it has been drained for transportation. 4. Always observe safe refueling and fuel handling prac- tices when refueling the unit after transportation or storage.
8 Assembly GENERAL All of the major assembly procedures on your new Chipper/Shredder were performed at the factory, and only the items listed in this section need to be taken care of to make your unit fully operational.
9 Assembly HOPPER 1. Attach the hopper to the rotor housing, using care to engage the metal lip of the hopper liner to the inside of the housing as shown in figure 3. 2. Secure the hopper to the rotor housing using (2) 5/16 x 1/2 hex head bolts and (2) 5/16 flat washers.
C. Bag The two-bushel bag is standard equipment and attaches in seconds for direct, one-step bagging. D. The Support Leg And Wheels The sturdy support leg and wide-track wheels give your chipper/shredder a stable, 3-point stance, allowing solid positioning on virtually all surfaces.
SPECIFICATIONS MODEL 5/14 MODEL 8/14 Engine B&S 825 Series OHV B&S 1450 Series OHV Chipping Capacity 2 1/2" 3" Chipping Knives 2 2 Shredding Hammers 2 - Triangular 2 - Triangular 2 -.
DESCRIPTION General Your new chipper/shredder is designed to permit years of trouble-free operation while handling a wide range of chipping and shredding needs. To help you get the most out of your investment, as well as to help you understand how the unit works, this section explains the basic operation of the chipper/ shredder.
CHECKS BEFORE ST ARTING 1. Inspect the chipper cone and shredder hopper for debris and other objects that may have fallen into the machine while the unit was idle, and remove them before starting the unit. Before reaching into the openings, always disconnect the spark plug wire at the spark plug.
Never wrap your fingers around tree limbs and branches so tightly that you can’t let go quickly if the tree limb or branch is suddenly pulled into the chipper block or shred- der hopper area. Leaves and other lightweight organic matter can be quickly shredded in your chipper/ shredder and reduced to 1/20th of their original volume.
15 Operation MA TERIAL PROCESSING General Most materials to be processed can be handled more efficiently by observing the following chipper/shredder operating tips: Shredding 1. Don’t overload the shredder hopper by dumping large volumes of material into the hopper opening.
OPERATION TYPE OF WASTE PERMITTED SIZE LIMITATIONS NOTES Shredding Dry, moist, or wet organic Branches and twigs Alternately chip or material, including leaves, plants, up to 1/2" diameter shred wet, green flowers, fruits, vegetables. and 18" long.
Normal Care Procedures - Perform Each Item At Use Interval Shown * s r H 0 0 1 s r H 5 2 s r H 5 e g a P M E T I Check For Loose Parts & Hardware 15 L Check Oil Level And Add As Req’d 16 L 6 1 l.
Oil Level 1. Oil level must be full. Check the oil level by removing oil fill plug. Oil level should be up to the bottom of the fill plug opening (see Figure 10).
Clean Engine Fins/Air Intake Area The engine that powers this chipper/shredder is air- cooled, and requires unobstructed air flow into and around the engine.
Inspect/Sharpen Chipping Knives This unit’s high-quality chipping knives are manufactured from a high-quality precision tempered steel, and are designed to provide positive feeding of tree limbs and branches, as well as exceptionally long service life.
TEMPORAR Y ST ORAGE (30 Days Or Less) Remember, the chipper/shredder fuel tank probably will still contain some gasoline, so never store the chipper/ shredder indoors or in any other area where fuel vapor could travel to any ignition source.
S E I D E M E R E S U A C E L B I S S O P M O T P M Y S . s a g d d A • . s a g f o t u O • . t r a t s t ’ n o w e n i g n E • Spark plug wire disconnected. • Connect spark plug wire. • Engine controls set wrong. • Check engine controls and adjust.
REP AIR Engine Service Your chipper/shredder engine requires routine mainte- nance for long-life and trouble-free operation. Consult the manufacturer’s manual provided with this unit for specific recommendations and service procedures.
24 T roubleshooting & Repair 4. Using leather work gloves to protect your hands from sharp edges, carefully rotate the rotor counterclock- wise until the first worn hammer is at the top position. 5. Before proceeding, note the assembly sequence of the hammer, spacer, spacer tube, and hardware.
• If the spacer tube has deep grooves worn into it, do not reuse the part - replace it using an exact factory replacement part only. • Rotate or flip the hammer to provide a new cutting edge, or install a new hammer if worn out or dam- aged.
26 T roubleshooting & Repair 4. Using a 1/4” hex wrench, loosen and remove the two socket head cap screws holding the chipper knife in place (access the screw heads from the rear of the unit), and remove the chipper knife. See Figure 24 for location and temporary removal of an access plug that permits removal of the capscrews.
OPTIONS & ACCESSORIES Several optional items and accessories are available that can help increase the usefulness and utility of your chip- per/shredder unit: V acuum Attachment This easy-to-add ac.
Briggs & Stratton Power Products Group, L.L.C. Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved www.BRIGGSandSTRATTON.
Een belangrijk punt na aankoop van elk apparaat Snapper 5/14 SERIES (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Snapper 5/14 SERIES heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Snapper 5/14 SERIES vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Snapper 5/14 SERIES leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Snapper 5/14 SERIES krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Snapper 5/14 SERIES bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Snapper 5/14 SERIES kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Snapper 5/14 SERIES . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
