Gebruiksaanwijzing /service van het product 211014 van de fabrikant Spalding
Ga naar pagina of 30
1 03/05 P/N 211014 Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-632 7921 Internet Address: http://www.
2 P/N 211014 03/05 201246 1 1/04 In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339 F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system.
3 03/05 P/N 211014 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s basketball systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to instructions.
4 P/N 211014 03/05 Get to know the basic parts of your basketball system... FRONT VIEW TOP POLE BACK VIEW MIDDLE POLE FRONT COVER RIM BOTTOM POLE STRUTS ELEV A TOR ASSEMBL Y BACKBOARD BASE WHEEL CARRI.
5 03/05 P/N 211014 P AR TS LIST (SEE P ARTS IDENTIFIER) Item Qty Part No Description P-1 1 908164 Top Pole Section P-2 1 908107 Middle Pole Section (with Label) P-3 1 908165 Bottom Pole Section P-4 2 .
6 P/N 211014 03/05 P AR TS IDENTIFIER P-31 (1) P-30 (1) P-18 (1) P-26 (1) P-28 (2) P-32 (1) P-22 (1) P-23 (1) P-29 (1) P-24 (1) P-25 (1) P-21 (2) P-19 (2) P-20 (2) P-14 (1) P-15 (1) P-16 (2) P-17 (2) 204532 11/04 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position.
7 03/05 P/N 211014 HARDW ARE LIST (SEE HARDW ARE IDENTIFIER) Item Qty Part No Description H-1 4 206938 Pushnut, Black H-2 1 203223 Bolt, Carriage, 5/16-18 x 1" Long H-3 1 202662 Bolt, Hex, 5/16-18 x 4.5" Long H-4 7 203218 Washer 5/16 H-5 1 200188 Rod 3/8 x 5.
8 P/N 211014 03/05 Item H-6 (1) Item H-8 (1) Item H-12 (1) Item H-18 (8) Item H-19 (1) Item H-31 (1) Item H-25 (2) Item H-21 (2) Item #H-29 (4) Item H-3 (1) Item #H-10 (1) Item H-16 (2) Item H-27 (4) .
9 03/05 P/N 211014 Item H-20 (4) Item H-23 (2) Item H-26 (6) Item H-4 (7) Item H-15 (8) HARDW ARE IDENTIFIER (NUTS, W ASHERS & MET AL SP ACERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS & CAPS) I.
10 P/N 211014 03/05 SECTION A: ASSEMBLE THE POLES Wood Scrap P-2 P-1 5" (13 cm) 5" (13 cm) P-1 P-3 P-2 Pole Identification Sticker Pole Identification Sticker 2.
11 03/05 P/N 211014 While maintaining alignment, bounce assembly and lower section (P-3) together as shown until they no longer move toward taped reference mark. P-1 P-2 P-3 3. WOOD SCRAP (NOT SUPPLIED) TROUGH Align dimple of middle pole section (P-2) into trough of bottom pole section (P-3) as shown.
12 P/N 211014 03/05 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section. 1. Insert axle (P-5) through wheel bracket (P-4). Secure wheels (P-28) to axle using pushnuts (H-1). Carefully tap pushnut s (H-1) onto axle with hammer or mallet.
13 03/05 P/N 211014 3. Install rod (H-5) through holes in bottom pole section (P-3) and eyebolt (H-6). 2. Install wheel assembly to base (P-8) using bolt (H-2), and nut (H-1 1) as shown.
14 P/N 211014 03/05 H-26 H-5 H-6 P-8 H-4 P-26 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. W ARNING! Insert pole assembly into tank (P-8) and through center hole on wheel assembly as shown.
15 03/05 P/N 211014 5. P-13 P-13 Secure tank strut s (P-13) to pole using bolt (H-3), washers (H-4) and nut (H-23) as shown. Place bolt cover (H-7) over exposed end of bolt as shown. Rotate non-secured ends of t ank struts (P-13) outward to mounting holes in tank as shown.
16 P/N 211014 03/05 6. 7. Secure ends of tank strut s (P-13) to tank using bolt (H-21), washers (H-4) and nut (H-1 1) as shown. Repeat for opposite side. Install upper pivot bracket (P-14) to front of base using bolt (H-8), washer (H-9) and nut (H-26) as shown.
17 03/05 P/N 211014 H-1 P-6 P-5 P-4 P-6 H-1 10. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORT ANT! Insert axle (P-5) through wheel bracket (P-4). Secure wheels (P-6) to axle using pushnuts (H-1). Carefully tap pushnut s onto axle with hammer or mallet.
18 P/N 211014 03/05 Position base as shown. Secure wheel bracket assembly with disc (P-23), washer (H-9) and nut (H-26) as shown. H-10 P-23 H-9 H-26 Carefully reposition entire assembly as shown: 11 . TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
19 03/05 P/N 211014 SECTION C: ASSEMBLE THE ELEV A TOR SYSTEM & BACKBOARD This is what your system will look like when you’ve finished this section.
20 P/N 211014 03/05 P-1 P-18 P-20 H-15 H-15 P-19 H-17 P-20 P-19 P-17 H-18 H-19 H-18 1. While the system is securely resting on the sawhorse. Install triangle plates (P-17) and elevator tubes (P-19 and P-20) to top pole section (P-1) as shown. Inst all pole cap (P-18) at this time.
21 03/05 P/N 211014 2. 3. Remove packaging materials from handle assemblies (P-10 and P-1 1). Remove screws on both sides of tube. P-1 1 P-10 P-1 1 Slide upper tube (P1 1) onto handle assembly (P-10). Reinsert screws removed in previous step as shown.
22 P/N 211014 03/05 Insert spacer (H-22) through springs (P-12) then assemble lower elevator tubes (P-19), and springs (P-12), to brackets (P-21) using bolts (H-18), plastic sp acers (H-20), metal spacer (H-22) and nut s (H-15) as shown. 5. P-21 H-20 H-15 H-20 H-22 P-12 H-22 P-12 6.
23 03/05 P/N 211014 7. P-31 H-33 H-32 P-30 H-31 Inst all Slam Jam Rim to Backboard P-29 P-32 H-31 H-32 H-33 A B C D E A. Fit rim (P-29) securely into bracket (P-30) as shown. Allow T -bolt (H-31) to slip through center hole in rim (P-29). B. Install reinforcement bracket (P-31) onto T -bolt (H-31) as shown.
24 P/N 211014 03/05 P-20 P-20 H-18 H-20 P-21 H-15 H-20 Assemble upper elevator tubes (P-20) to brackets using bolt (H-18), plastic sp acers (H-20), and nut (H-15) as shown. 8. P-19 P-19 TIGHTEN BOLT (H-18) IN LOCK NUT (H-15) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE.
25 03/05 P/N 211014 H-18 H-15 P-1 P-20 P-19 P-17 P-1 1 9. Install handle assembly (P-10 and P-1 1) to lower elevator tubes (P-19) using bolt (H-18), spacers (H-14), and nut (H-15) as shown. P-20 P-19 H-14 H-14 Secure the handle assembly (P-10 & P-1 1) to pole bracket (P-9) using bolt (H-30) and nut (H-23) as shown.
26 P/N 211014 03/05 P-20 P-12 H-15 P-20 11 . Insert bolt (H-18) through left side upper elevator tube (P-20), then stretch spring (P-12) onto bolt (H-18). Continue inserting bolt (H-18) through right side upper elevator tube (P-20) and secure with nut (H-15).
27 03/05 P/N 211014 12. Install net clip s (H-28). CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
28 P/N 211014 03/05 Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snap s into position. Net must be centered through clip. NET NET CLIP SIDE VIEW NET NET CLIP 13.
29 03/05 P/N 211014 SECTION D: INST ALL FRONT COVER & HANDLE 1. Attach front cover (P-22) to hinge tubes (P-16) using carriage bolt s (H-27) and flange nuts (H-1 1) as shown. P-22 H-27 H-1 1 P-16 Upright system and fill base (P-8) with water (approximately 40 gallons) and snap fill cap (P-24) in place.
30 P/N 211014 03/05 1. Roll assembly to desired playing area. Secure assembly to ground using strap (P-26) and tie down stake (P-25). P-26 P-25 P-8 SECTION E: SECURING THE SYSTEM & APPL YING LABEL 2. Apply Height Adjustment and Moving Label (P-27) to front of pole, where it is clearly visible.
Een belangrijk punt na aankoop van elk apparaat Spalding 211014 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Spalding 211014 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Spalding 211014 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Spalding 211014 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Spalding 211014 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Spalding 211014 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Spalding 211014 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Spalding 211014 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
