Gebruiksaanwijzing /service van het product GR30 van de fabrikant Stanley Black & Decker
Ga naar pagina of 22
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 49237 2/2015 V er . 5 USER MANUAL Safety , Operation and Maintenance GR30 HYDRAULIC GRINDER.
2 ► GR30 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ ______.
GR30 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► GR30 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
GR30 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► GR30 User Manual • W arning: Hydraulic uid under pressure could cause skin injection injury . If you are injured by hydraulic uid, get medical attention immediately . • Keep the wheel off all surfaces when starting the grinder . • Always carry the tool with the wheel stopped.
GR30 User Manual ◄ 7 28322 CE Decal 28409 Composite Decal SAFETY T AG P/N 15875 (shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
8 ► GR30 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
GR30 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
10 ► GR30 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
GR30 User Manual ◄ 1 1 PRE-OPERA TION PROCEDURES The GR30 Hydraulic Grinder Requires minimum setup for operation. When the installation and operation in- structions are carefully followed, the tool will provide years of efcient and reliable service.
12 ► GR30 User Manual 1. Make sure the hydraulic system control valve is in the OFF position when coupling or uncoupling the hoses. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
GR30 User Manual ◄ 13 5. Check the tool for oil leaks. If leaks are observed, do not use the tool; have the equipment serviced before use. IMPORT ANT Check the speed of the motor output shaft after every 100 hours of operation. HYDRAULIC POWER SOURCE CHECK 1.
14 ► GR30 User Manual ST ARTUP At the beginning of each shift, or after a new wheel is installed, run the grinder at operating speed for at least one minute before starting work. • Move the hydraulic system control valve to the ON position. • Slowly squeeze the trigger .
GR30 User Manual ◄ 15 NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools.
16 ► GR30 User Manual This section describes how to nd and resolve problems users may experience. If a situation occurs that is not covered, call your Stanley Customer Service represen- tative for assistance. Symptom Possible Cause Solution T ool does not operate.
GR30 User Manual ◄ 17 Symptom Possible Cause Solution Fluid gets hot, power unit working hard. Open-center tool on closed-center circuit. T ool designed for open-center hydraulic system. T oo much uid going through tool. Adjust ow for 9 gpm/34 lpm maxi - mum.
18 ► GR30 User Manual Flow Range ................................................................................................................................. 7–9 gpm/26–34 lpm LPM Optimum ow ..............................................
GR30 User Manual ◄ 19 GR30 Parts Illustration 20 10 16 46 49 16 47 44 48 1 43 73 4 37 45 18 65 2 42 40 31 27 8 28 30 68 39 29 70 26 25 24 66 63 62 54 21 1 38 76 67 78 6 79 12 53 41 7 15 69 74 22 23 .
20 ► GR30 User Manual ITEM P ART NO. QTY DESCRIPTION 1 00026 2 O-RING 3/16 × 5/16 × 1/16 -008 2 00231 6 LOCKW ASHER 5/16" ID 3 00285 1 ROLL PIN 1/8 OD × .
GR30 User Manual ◄ 21 ITEM P ART NO. QTY DESCRIPTION 73 59049 1 MAIN HOUSING ASSY (INCL ITEMS 16, 43) 74 60677 1 TRIGGER CASTING 75 60678 1 TRIGGER MOUNT CASTING 76 65480 1 SPRING 77 60681 1 TRIGGER LOCK CASTING 78 350041 1 HOLLOW HEX PLUG -4 SAE 79 350770 1 O-RING .
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Een belangrijk punt na aankoop van elk apparaat Stanley Black & Decker GR30 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Stanley Black & Decker GR30 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Stanley Black & Decker GR30 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Stanley Black & Decker GR30 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Stanley Black & Decker GR30 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Stanley Black & Decker GR30 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Stanley Black & Decker GR30 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Stanley Black & Decker GR30 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
