Gebruiksaanwijzing /service van het product M45-00151 van de fabrikant StudioTech
Ga naar pagina of 31
Copyright © 2009 by Studio T echnologies, Inc., all rights reserved www .studio-tech.com 50216-0309, Issue Preliminary 2 User Guide Issue Preliminary 2, March 2009 This User Guide is applicable for s.
This page intentionally left blank..
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 3 T able of Contents Introduction ................................................................... 5 Installation ..................................................
Issue Preliminary 2, March 2009 Model 45 User Guide Page 4 Studio T echnologies, Inc. This page intentionally left blank..
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 5 Introduction The Model 45 is designed to interface 2-wire full-duplex party-line (PL) intercom circuits with 4-wire audio circuits associ- ated with matrix intercom systems.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 6 Studio T echnologies, Inc. 2- W ire P arty-Line Interface The Model 45’s two-channel 2-wire party- line interface is optimized for direct connec- tion with a dual-channel party-line intercom circuit.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 7 of its 2-wire-to-4-wire hybrid circuits. Each of the two independent circuits provides low noise and distortion, good frequency response, and high return-loss (“nulling”), even when presented with a wide range of 2-wire party-line conditions.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 8 Studio T echnologies, Inc. of only 2 dB is required. The RTS ADAM™ series of matrix intercom systems has a nominal level of +8 dBu. This level also applies to their RVON-I/O V oIP products. As such, reducing their nominal input and output levels by 4 dB will ensure optimal compatibility .
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 9 audio quality , advanced users might need to disable it. This would allow full control over the Model 45’s two hybrid circuits, enabling them to be used in a completely independent manner .
Issue Preliminary 2, March 2009 Model 45 User Guide Page 10 Studio T echnologies, Inc. The next step was to identify resources that would improve the installation process and make operation more reliable. This led to the use of standard 3-pin XLR-type audio connectors, enabling rapid installa- tion and troubleshooting in any locale.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 11 cables will help to ensure more reliable and consistent intercom system performance. The differential (“balanced”) 4-wire circuits are typically not impacted by the length of their interconnecting cables.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 12 Studio T echnologies, Inc. Once the desired one or two Model 45 units have been installed in a rack -mount front panel, the assembly can be mounted into the designated equipment rack. One space (“1U” or 1.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 13 unbalanced source in this manner results in hum or noise, connect XLR pin 2 to high (+ or hot) and pin 3 to shield; leave pin 1 unterminated. 4- Wire Line Outputs The Model 45’s dual-channel interface pro- vides two analog line-level audio outputs.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 14 Studio T echnologies, Inc. pin 3 of the Model 45’s 2-wire party-line intercom interface, will be utilized. Pin 2, the Model 45’s audio channel 1, will only be used for connecting DC power to the connected devices.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 15 External 24 V olts as the Power Source As previously discussed, the Model 45 can be powered by a source of 24 volts DC. A “locking” 2.1 x 5.5 mm coaxial power jack is located on the back panel of the unit.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 16 Studio T echnologies, Inc. drop can become appreciable in situations where belt pack operation wouldn’t nor - mally be impacted. P erforming accurate calculations in this scenario is a bit more difficult but might be required to ensure a reliable installation.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 17 external source of 24 volts is going to be connected switch 1 should be placed in its off (down) position.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 18 Studio T echnologies, Inc. interface to be auto nulled at approxi- mately the same time. The dual auto null mode allows a single “tap” of the button to initiate nulling of both hybrid circuits.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 19 the Model 45’s 2-wire-to-4-wire converter circuitry . These audio artifacts will not cause any damage but will be sent out of the 4-wire line outputs.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 20 Studio T echnologies, Inc. are fully isolated from the 2-wire intercom circuit. In this situation the Model 45’s only function is to route, by way of the hybrids, the 2-wire interface’s audio signals to and from the 4-wire outputs and inputs.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 21 pin 2 falls below 24 volts for a continuous 1- second interval. The hardware and software responds to this condition by turning off the power source to pin 2 and flashing the pin 2 LED as a warning.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 22 Studio T echnologies, Inc. device’s nominal level matches the Model 45’s level setting its actual nominal level may be significantly different.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 23 An auto null sequence begins with the muting of the 4-wire input and output signal paths associated with the channel being nulled. This is followed by a short period of 24 kHz signal that is sent out the 2-wire party-line intercom interface channel.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 24 Studio T echnologies, Inc. readily apparent. The front-panel LEDs will continue to display the DC power status of pins 2 and 3. But whether or not either or both LEDs are lit, the Model 45 will never apply 200 ohm terminations to pins 2 or 3.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 25 Note that while it’s easy to determine which software version is loaded into the Model 45 a trip back to the factory is required to update it. The 8-bit micro- controller that provides the unit’s logic “horsepower” also includes internal FLASH memory .
Issue Preliminary 2, March 2009 Model 45 User Guide Page 26 Studio T echnologies, Inc. unit. P ower can be provided by the con- nected intercom circuits or by way of an external source of 24 volts DC. The final step to achieve correct performance is for the auto null function on each Model 45 to be activated.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 27 Specifications General Audio: Frequency Response: ±2 .5 dB 100 Hz to 8 kHz Distortion (THD+N): <0.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 28 Studio T echnologies, Inc. Interfacing RTS® Matrix Intercom Systems with the Model 45 Interface Appendix A ADAM ™ Matrix Intercom System .
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 29 Interfacing Riedel® Artist™ Matrix Intercom System Analog Ports with the Model 45 Interface Appendix B.
Issue Preliminary 2, March 2009 Model 45 User Guide Page 30 Studio T echnologies, Inc. Interfacing Clear-Com® Matrix Intercom System Analog P orts with the Model 45 Interface Appendix C.
Model 45 User Guide Issue Preliminary 2, March 2009 Studio T echnologies, Inc. Page 31 This page intentionally left blank..
Een belangrijk punt na aankoop van elk apparaat StudioTech M45-00151 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen StudioTech M45-00151 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens StudioTech M45-00151 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding StudioTech M45-00151 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over StudioTech M45-00151 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van StudioTech M45-00151 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de StudioTech M45-00151 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met StudioTech M45-00151 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
