Gebruiksaanwijzing /service van het product D1320203 van de fabrikant TANDBERG
Ga naar pagina of 39
TANDBERG 3G Gateway Data port Command In terface User Guide T ANDBERG 3G Gateway Data port Command Interface User Guide Softwar e version R 3 D1320203 TANDBERG D1320203 1.
TANDBERG 3G Gateway Data port Command In terface User Guide Table of Contents 1. INTRODUCTION ...........................................................................................................................3 2. CONNECTIN G TO THE DATA PORT COM MAND INTERFACE THROUGH THE RS -232 PORT.
TANDBERG 3G Gateway Data port Command In terface User Guide 1. Introduction The TANDBERG 3G Gateway Data port Command Interface User Guide contains guidelines on how to us e the textual command interface supported by the 3G Gateway system, further referred to as 3G Gateway .
TANDBERG 3G Gateway Data port Command In terface User Guide 2. Connecting to the Data port Command Interface through the RS-232 port. The RS-232 port is a 9-pin, fem ale, sub-D connector located on the front of the 3G Gateway. The port is configured as a DCE (Data Communications Equipment).
TANDBERG 3G Gateway Data port Command In terface User Guide D1320203 5 If communication cannot be established between the PC /terminal and the TANDBERG 3G Gateway’s Data port the following should be.
TANDBERG 3G Gateway Data port Command In terface User Guide 3. Connecting to the Data port Co mmand Interface using Telnet The TANDBERG 3G Gateway has one LAN port. The 3G Gateway’s Telnet server provides access to the Data port Co mmand Interface through a 10/100 base T network interface supporting the TCP/IP protocol.
TANDBERG 3G Gateway Data port Command In terface User Guide 4. The TANDBERG 3G Gateway Commands 4.1. Introduction Typing ‘ ? ’ or ‘ help ’ when connected to the Data Port Comma nd Interface will return a list of valid commands. The commands are used to control the functions of the 3G Gateway.
TANDBERG 3G Gateway Data port Command In terface User Guide 4.1.2. Command types The commands can be divided into three major classes: • Parameter Configuration Commands, Xconf. • Status Commands, Xstat. • User Commands, Xcom. Parameter Configuration Commands are commands that set a system parameter to a specific value.
TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.1. System Configuration Commands Command: Description: Dialplan Mapping o f a call onto a se rvice or anot her call. Dialplan En try [1.. 64] Enable d: <On/Off> Dialplan Entry [1..64 ] Na m e: <S: 0, 30> Dialplan Entry [1 .
TANDBERG 3G Gateway Data port Command In terface User Guide distingui shed: • Net type - Either H324m, H323 or SIP of the outbound call. • AV mode – Th is mode deter mines the out bound audi o and vide o call settings.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 1 Prefi x: "207947 13 3" *c xConfigurat ion Dialpl a n Entry 1 Suffix: " " *c xConfi.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 2 Nam e: "avmode" *c xConfigurat ion Dialpla n Ent ry 2 Pro pe rt y 2 Value: &qu.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 4 Prefi x: "903700 10" *c xConfigurat ion Dialpl a n Entry 4 Suffix: " " *c xConfigu.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigurat ion Dialpla n Ent ry 4 Pro perty 14 Nam e : "entry5 _la bel " *c xConfigurat ion Dialpla n Ent ry 4 Pro pe rt y 14 .
TANDBERG 3G Gateway Data port Command In terface User Guide • Authentication Mode configures the use of authen tication against a gatekeeper. • Authentication ID Configures the user name used within an authen tication challenge • Authentication Password sets the password used within the auth en tication process.
TANDBERG 3G Gateway Data port Command In terface User Guide used when t he 3G Gateway is connected t o a LAN usin g DHCP. Wh en using t his mode, IP-address and IP-subnet m ask are not used because the DHCP se rver supplies these parameters. • Address: Sets the static IP addres s for the gi ven LAN interface.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfiguratio n ISDN Internationa lPrefix: "00" Loadlimit Sets the processor-load percentag e at which ca lls should be rout ed to anot her 3G Gatewa y.
TANDBERG 3G Gateway Data port Command In terface User Guide SNMP HostIPAddr [1..3]: < IPAd dr> --- parameters: • Mode: < On/Off/ReadOnly/TrapsOnly > • Community Name: Text st ring of m aximum 16 cha racters.
TANDBERG 3G Gateway Data port Command In terface User Guide Telnet Enables or disables telnet interface on the 3G Gateway Telnet Mode: <On/Off> --- Example of Telnet feedback: *c xConfigurat ion.
TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.2. General 3G Gateway Commands Command: Description: ExternalManager This command sets the path and address of the TMS serv er. A message is sent to TMS when the 3G Gateway starts up to signal TMS that the 3G Gateway is ready.
TANDBERG 3G Gateway Data port Command In terface User Guide OPC: <0 .. 16383> NetworkIndi cator: <Internati onal0/In ternational 1/National 0/Nationa l1> Law: <ALaw/ULaw> LinkSet [1 .. 2] Mode: <On/Off> LinkSet [1 .. 2] DPC: <0 .
TANDBERG 3G Gateway Data port Command In terface User Guide • Trunk CircuitIdentificationCode: The Circuit Identification Code is a unique id en tifier for a data time slot in a cable (trunk). In this case the CIC acts as base address and can be defined for eac h SS7 trun k and sets the first tim e-slot number of the respecti ve SS7 trunk.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigur ation SS7 Tr unk 1 Mo de: Off *c xConfigur ati on S S7 Tr u nk 1 DPC : 0 *c xConfiguration SS7 Trun k 1 CircuitIdentificationCo.
TANDBERG 3G Gateway Data port Command In terface User Guide *c xConfigur ati on S S7 R out e 7 DPC : 0 *c xConfigur ation SS7 R oute 7 Priori ty: 0 *c xConfigur ation SS7 R oute 7 LinkSet : Off *c xCo.
TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.3. System Status Commands Command: Description: BRI [1..4] Displays the status of the BRI lines BRI Parameters: • BRI [1.
TANDBERG 3G Gateway Data port Command In terface User Guide Nam e: "allowredirectivr" Value: " 0" Property: Nam e: "DTMFInfoScreen" Value: " On" *s/end OK Disk .
TANDBERG 3G Gateway Data port Command In terface User Guide Parameters: • Address , The IP address of the ex t ernal managem ent system • Protocol , the protocol used to acce ss the management sys.
TANDBERG 3G Gateway Data port Command In terface User Guide • Port, the gatekeeper port t he 3G Gateway is connected with Example of H323Gatekeeper feedback: *s H323Gatekeeper (s tatus=Registered): Address: "10.
TANDBERG 3G Gateway Data port Command In terface User Guide NTP Returns the IP address of the NTP server. Status format: < Status > <Address> <Port> <Last Update> <Last Correction> --- Parameters: • Status, indicates whether the NTP server is active or not.
TANDBERG 3G Gateway Data port Command In terface User Guide Channel 10 (type=BChannel, status =Id le): / Channel 11 (type=BChannel, status =Id le): / Channel 12 (type=BChannel, status =Id le): / Chann.
TANDBERG 3G Gateway Data port Command In terface User Guide Name> ReleaseDate> Configuration Telephony:> VideoTelephony:> <Hardware : Version> SerialNumber> MainBoard> Additional Board> Configuration: PRI> TemperatureCelcius> TemperatureFahrenheit> --- Parameters: • ProductType , the name of the product, e.
TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.4. Debug Commands Command: Desription : Syslog Enables a real- time log of B onding, H.221 and H 324m, ISDN , RTSP, IVi der, and IVide r Engine activi ty. Note! H323 and SIP loggi ng is prese nted using t he followi ng command: tsh –a H323 (SIP) .
TANDBERG 3G Gateway Data port Command In terface User Guide 4.2.5. Special (Xcommand) Commands Command: Description: Boot Reboots the system. Example: xComm and Boot *r Result (status=OK): / *r/end OK CUIL rebo ot request , restarting CheckDisk This command shows t he presence and th e s tatus of the internal harddisk.
TANDBERG 3G Gateway Data port Command In terface User Guide • CallingParty: <S:0, 60> Service telephone number. • NetType: <All/H324m/H323/SIP> Nettype of t he end poin t to be called. • CallType: <Tlph/Vtlph> Call ty pe is either voi ce (Tl p h ), o r voi ce an d vi d e o (Vt lp h).
TANDBERG 3G Gateway Data port Command In terface User Guide EraseDisk This command wipes all the data from the internal harddisk Example: xComma nd EraseDisk *r Result (status=OK): *r/end OK FeedbackDeregister Command use d to deregi ster XML feedbac k over HTTP(S) .
TANDBERG 3G Gateway Data port Command In terface User Guide *r Result (status=OK): ID: 2 *r/end OK OptionKeyAdd Command used to set new option key s. Parameters: • Key(r): <S: 0, 90> opti o n key NOTE! Alway s reboot the system after adding o ption keys, for the opti on key to ta ke effect.
TANDBERG 3G Gateway Data port Command In terface User Guide *r Result (status=OK): / *r/end OK D1320203 3 7.
TANDBERG 3G Gateway Data port Command In terface User Guide General User Commands About Shows following system information: Software ve rsion: R3.0 Portions of this softwa re are licensed under 3r d pa rty licenses. See th e CD accompanying this product for det ails.
TANDBERG 3G Gateway Data port Command In terface User Guide D1320203 3 9 (note: deregistration with index=0 will deregister all registered expressions) Examples : "xfeedback register status/ca ll.
Een belangrijk punt na aankoop van elk apparaat TANDBERG D1320203 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TANDBERG D1320203 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TANDBERG D1320203 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TANDBERG D1320203 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TANDBERG D1320203 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TANDBERG D1320203 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TANDBERG D1320203 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TANDBERG D1320203 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
