Gebruiksaanwijzing /service van het product TB2000 van de fabrikant Troy-Bilt
Ga naar pagina of 22
©2000 MTD SOUTHWEST INC Models TB2000 – 22.5cc Curved Shaft FORM 182821 (1/01) (10201 rev . A) Printed in U.S.A. Owner/Operator Manual 2-Cycle T rimmer • Safety • Assembly • Operation • Mai.
2 Introduction THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. Y ou will find it to be a great labor -saving device. This operator’ s manual provides you with easy-to-understand oper- ating instructions.
3 Ser vice Information SERVICE INFORMA TION Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer .
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger . The instructions or warnings they give are not substitutes for proper accident prevention measur es.
5 Safety (continued) • Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressur e in the tank.
6 Safety (continued) SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety , assembly , operating and maintenance and repair information.
7 Safety (continued) SYMBOL MEANING • ON/OFF STOP CONTROL ON / ST ART / RUN • ON/OFF STOP CONTROL OFF OR STOP • HOT SURF ACE WARNING Do not touch a hot muffler , gear housing or cylinder . Y ou may get burned. These parts get extremely hot fr om operation.
8 Section 2 Know Y our Unit APPLICA TIONS As a trimmer; • Cutting grass and light weeds. • Edging • Decorative trimming around tr ees, fences, etc.
9 Section 3 Assembly On some units, the D-handle may be preinstalled and only requir e loosening the screws and adjusting the D-handle to the operator . Go to step 4 for adjusting the D-handle if preinstalled. INST ALLING AND ADJUSTING THE D-HANDLE 1.
10 Section 4 Oil and Fuel Oil and Gas Mixing Instructions Old and/or improperly mixed fuel ar e the main reasons for the unit not running pr operly . Be sure to use fresh, clean unleaded fuel. Follow the instructions carefully for the pr oper fuel/oil mixture.
11 Section 5 Operation ST ARTING INSTRUCTIONS Operate this unit only in a well ventilated area outdoors. Carbon monoxide exhaust fumes can be lethal in a confined area. Avoid accidental starting. Be in the starting position whenever pulling the starting rope.
12 Operation (continued) HOLDING THE TRIMMER Always wear eye, hearing, foot and body protec- tion to reduce the risk of injury when operating this unit. Before operating the unit, stand in the operating posi- tion (Fig. 5-4). Check for the following: • The operator is wearing eye protection and pr oper clothing.
13 Operation (continued) DECORA TIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around tr ees, posts, fences, etc. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground (Fig. 5-5). Section 6 MAINTENANCE NOTE: Some maintenance procedures may require special tools or skills.
14 Maintenance (continued) LINE INST ALLA TION This section covers both Membrane line and standard single line installation. Always use manufacturer’ s 0.080 inch (2.03 mm) replacement line. Line other than specified may make the engine overheat or fail.
15 Maintenance (continued) 12. Insert the ends of the line into the two holding slots (Fig. 6-6). Leave about 4 inches (102 mm) of line beyond the holding slots. 13. Insert the ends of the line thr ough the eyelets in the outer spool and place inner reel inside the outer spool (Fig.
16 Fig. 6-9 Fig. 6-11 Fig. 6-12 Fig. 6-10 Maintenance (continued) AIR FIL TER MAINTENANCE Cleaning the Air Filter T o avoid serious personal injury , always tur n your trimmer off and allow it to cool befor e you clean or do any maintenance on it. Clean and re-oil the air filter every 10 hours of opera- tion.
17 Maintenance (continued) If after checking the fuel mixture and cleaning the air filter the engine still will not idle, adjust the idle speed screw as follows. 1. Start the engine and let it run at a high idle for a minute to warm up. 2. Release the throttle trigger and let the engine idle.
18 Maintenance (continued) ACCESSORIES/REPLACEMENT P ARTS Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181765 Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182153 Replacement Line Cartridge .
19 Section 7 T roubleshooting CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Repl.
20 Section 8 Specifications Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Displacement . . . . . . . . . . . . . . . . . . . .
21 Notes.
MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty , including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified.
Een belangrijk punt na aankoop van elk apparaat Troy-Bilt TB2000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Troy-Bilt TB2000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Troy-Bilt TB2000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Troy-Bilt TB2000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Troy-Bilt TB2000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Troy-Bilt TB2000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Troy-Bilt TB2000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Troy-Bilt TB2000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
