Gebruiksaanwijzing /service van het product S1572 ATX van de fabrikant TYAN
Ga naar pagina of 40
Revision 1.0 TYAN S1572 ATX Pentium Class 75 thru 200MHz 430TX PCI-ISA System Board User's Manual.
2 S1572-001-01 http://www.tyan.com Notice for the USA Compliance Information Statement ( Declaration of Comformity Procedure) DoC FCC Part 15: This Device complies with Part 15 of the FCC Rules.
3 S1572-001-01 http://www.tyan.com Table Of Contents 1. Introduction....................................................................... 3 1.1 Overview................................................................3 1.2 Hardware Specifications....
4 S1572-001-01 http://www.tyan.com 1. Introduction 1.1 Overview The S1572 is a quality, high performance mainboard designed for Intel Pentium microprocessors. This mainboard utilizes the Intel 430TX chipset and can support CPU speeds of 75MHz through 200MHz.
5 S1572-001-01 http://www.tyan.com 1.2 Hardware Specifications/Features w CPU Intel Pentium 75 MHz thru 200 MHz (Socket 7) Intel Pentium P55C/P54CTB Overdrive (MMX) Cyrix/IBM/SGS M1/6x86 P120+, P150+, P166+, and AMD K5 PR90 through PR166.
6 S1572-001-01 http://www.tyan.com 1.3 Software Specifications w BIOS Award or AMI BIOS AT CMOS setup, BIOS/CHIPSET setup, and hard disk utility included. Support for easy BIOS upgrades with flash EPROM chip. w O.S. Operates with MS-DOS, Windows 3.x, Windows for Work Group 3.
7 S1572-001-01 http://www.tyan.com 2. Board Installation 2.1 Unpacking The mainboard package should contain the following: w S1572 Mainboard w One IDE 40 pin cable w One 34 pin floppy cable w User&apo.
8 S1572-001-01 http://www.tyan.com Parallel Port PCI Slot 1 PCI Slot 2 PCI Slot 3 PCI Slot 4 PCI Slot 5 ISA Slot 1 ISA Slot 2 ISA Slot 3 3. On Board Resource Setting Figure 3.
9 S1572-001-01 http://www.tyan.com 3.2 Jumper Settings CPU Speed Settings for Pentium P54C and P55C: JP4 JP5 JP23 CPU Speed off off 1-2,3-4 75MHz off off 3-4 90MHz off off 1-2 100MHz on off 3-4 120MHz.
10 S1572-001-01 http://www.tyan.com BIOS Voltage Select: JP2 (Default is 5V) BIOS 5V BIOS 12V JP2 1-2 2-3 J8 Jumper Block: Desc. PIN# Soft Power 1-2 Ext SMI 3-4 IR1 8-11 Pri HDD LED 13-14 Sec HDD LED 15-16 PWR LED 18-20 Reset SW 22-23 Speaker 24-27 CPU Select: Default P54C, P55C(MMX), & Cyrix These jumpers need not be changed.
11 S1572-001-01 http://www.tyan.com Reset Connector: J8 pin 22-23 Pinout Assignment 22 Power Good 23 Ground Flash EPROM: JP2 This jumper should be left at the factory default.
12 S1572-001-01 http://www.tyan.com Infra Red Interface: J8 pins 8-11 and J2 Pinout Assignments 1(8) Signal In 2(9) Gnd 3(10) Signal Out 4(11) VCC I/O Port Setting: J15 and J16 J15 J16 For Serial Port.
13 S1572-001-01 http://www.tyan.com 3.3 CMOS RTC CMOS RTC includes an internal battery and Real Time Clock circuit. It provides the date and the time for the system. Normally the life span of a RTC internal battery is 10 years. This function is built onto the Intel TX chipset and cannot be field upgraded.
14 S1572-001-01 http://www.tyan.com Refer to chapter 5 for Flash EPROM upgrade procedures. 3.9 Hardware CMOS & Password Reset If you have been locked out of your system because you forgot your pass- word or set the CMOS incorrectly, follow the instructions below.
15 S1572-001-01 http://www.tyan.com 3.10 DRAM Installation The S1572 uses a 64-bit data path from memory to CPU and can accommodate up to 256MB of RAM. The mainboard supports Fast Page Mode, and EDO (Extended Data Out) 72 pin SIMMs. SDRAM(Synchronous) are also supported in the DIMM slots.
16 S1572-001-01 http://www.tyan.com 1. Make sure the ZIF socket lever is up. To raise the lever, pull it out to the side a little and raise it as far as it will go. The top plate will slide back. 2. Align the CPU and socket Pin 1 corners. The pins on the bottom should align with the rows of holes in the socket.
17 S1572-001-01 http://www.tyan.com 3.12 Upgrading Cache Memory The S1572's 512kb of on-board pipelined burst SRAM and cannot be field upgraded. The TX chipset can cache a maximium of 64MB of RAM. 3.13 Peripheral Device Installation After all the jumpers on the mainboard have been set, then it can be mounted into the case.
18 S1572-001-01 http://www.tyan.com 4. BIOS Configuration Award's BIOS has a built in setup program that allows the user to modify the basic system configuration. This type of information is stored in the battery-backed CMOS NVRAM. Entering incorrect information or for- getting your password can lock you out of your system.
19 S1572-001-01 http://www.tyan.com 4.2. Control Keys PgUp key Increases the numeric value or make changes PgDn key Decreases the numeric value or make changes F1 key General help, only for Status Pag.
20 S1572-001-01 http://www.tyan.com 4.3. Getting Help 4.3.1. Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen.
21 S1572-001-01 http://www.tyan.com w Standard CMOS setup This setup page includes all the items in a standard compatible BIOS. w BIOS features setup This setup page includes all of the enhanced features of Award's BIOS. w Chipset features setup This setup page includes all the items of the 430TX chipset features.
22 S1572-001-01 http://www.tyan.com w Date The date format is <month>, <day>, <year>. Press <F3> to show the calendar. Base Memory: 640 K Extended Memory: 7168 K Expanded Memor.
23 S1572-001-01 http://www.tyan.com N o n e N o f l op p y d r i v e i n s t a l l e d 3 60 K , 5 . 2 5 i n . 5 - 1 / 4 i n c h P C - t y p e s t a n d a r d d r i v e ; 36 0 k i l ob y t e c a pa c i t y 1 . 2 M , 5 . 2 5 i n . 5 - 1 / 4 i n c h A T - t y p e h i g h - d e n s i t y d r i v e ; 1 .
24 S1572-001-01 http://www.tyan.com w Video This category detects the type of graphics adapter used for the primary display system. It must match your video display card and monitor. Al- though secondary monitors are supported, you do not have to select that type in setup.
25 S1572-001-01 http://www.tyan.com Expanded Memory Expanded Memory (EMS) defines a 64K page frame in the area between 640K and 1Mb containing four 16K pages that are windows into the EMS memory. Programs issue requests to the EMS manager to switch the page to any part of EMS memory.
26 S1572-001-01 http://www.tyan.com w Virus warning This category flashes on screen. During and after the system boot up, any attempt to write to the boot sector or the partition table of the hard disk drive will halt the system and the following error message will appear.
27 S1572-001-01 http://www.tyan.com w Boot Up Floppy Seek During POST, the BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 720K, 1.2M and 1.44M are all 80 tracks. Default value is Enabled Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks.
28 S1572-001-01 http://www.tyan.com ROM ISA BIOS CHIPSET SETUP UTILITY AWARD SOFTWARE, INC. Auto Configuration :Enabled DRAM Timing :70ns DRAM Leadoff Timing :10/6/3 DRAM Readburst (EDO/FP) :x222/x333.
29 S1572-001-01 http://www.tyan.com w Power Management Options are disabled, user defined, Min saving, and Max saving. w PM Control by APM Options are " Y es" and "No". When set for "No", system BIOS will ignore APM when power managing the system.
30 S1572-001-01 http://www.tyan.com w Doze Mode Defines the continous idle time before the system enters Doze mode. w Standby Mode Defines the continous idle time before the system enters Standby mode. w Reload Global Timer Events Defines the the activities that can cause the PM timers to reload.
31 S1572-001-01 http://www.tyan.com 4.8 PCI Slot Configuration ROM ISA BIOS PCI SLOT CONFIGUR ATION AW ARD SOFT WARE, INC. Resource Controlled by :Manual Reset Configuration :Disabled IRQ3 assigned to.
32 S1572-001-01 http://www.tyan.com w Resources Controlled By The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible devices. If you select Auto, all the interrupt request and DMA assignment fields disappear, as the BIOS automatically assigns them.
33 S1572-001-01 http://www.tyan.com 4.9 Integrated Peripherals Integrated Peripherals Award Software, Inc. IDE HDD Block Mode :Enabled IDE Primary Master PIO :Auto IDE Primary Slave PIO :Auto IDE Seco.
34 S1572-001-01 http://www.tyan.com STANDARD CMOS SETUP PASSWORD SETTING BIOS FE ATURES SETUP IDE HDD AUTO DETECTION CHIPSET FE ATURES SETUP DAVE & EXIT SETUP PCI SLOT configuration EXIT WITH OUT SAVING LOAD SETUP DEFAU LTS 4.10. LOAD SETUP DEFAU LTS ROM ISA BIOS CMOS SETUP UTILITY AW ARD SOFT W ARE INC.
35 S1572-001-01 http://www.tyan.com ROM ISA BIOS CMOS SETUP UTILITY AW ARD SOFT WARE, INC. STANDARD CMOS SETUP PASSWORD SETTING BIOS FE ATURES SETUP IDE HDD AUTO DETECTION CHIPSET FE ATURES SETUP DAVE.
36 S1572-001-01 http://www.tyan.com 4.12. IDE HDD AUTO DETECTION ROM ISA BIOS CMOS SETUP UTILITY AW ARD SOFT WARE, INC. CYLS. HEAD PRECOMP LANZONE SECTORS Drive C: (202 Mb) 989 12 65535 989 35 Do you want to accept this as drive C (Y/N)? Esc:Skip Type "Y" to accept the H.
37 S1572-001-01 http://www.tyan.com 5.0 Flash Writer Utility Y ou can upgrade the BIOS of your mainboard by using a "Flash Memory Writer"(FMW) utilit y . This utility can be downloaded from the factory's BBS(Consult your system vendor for the phone #).
38 S1572-001-01 http://www.tyan.com T o reprogram the System BIOS, you must first do the following: 1. Check jumper JP2.(Default pins 1-2) The S1572 uses a 5V Flash EPROM so jumper JP2 should be left in the default postion on pins 1 and 2. This jumper should never be moved.
39 S1572-001-01 http://www.tyan.com Once you have satisfied the two requirements mentioned above, you can run FM W . You can copy the contents of the “ Flash ” directory to your hard drive, or you can run the utility from a backup of the support floppy disk.
40 S1572-001-01 http://www.tyan.com 6.0 System Resource 6.1. TIMER & DMA CHANNEL MAP TIMER MAP: TIMER Channel-0 system timer interrupt TIMER Channel-1 DRAM REFRESH request TIMER Channel-2 SPEAKER .
Een belangrijk punt na aankoop van elk apparaat TYAN TYAN S1572 ATX (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen TYAN TYAN S1572 ATX heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens TYAN TYAN S1572 ATX vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding TYAN TYAN S1572 ATX leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over TYAN TYAN S1572 ATX krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van TYAN TYAN S1572 ATX bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de TYAN TYAN S1572 ATX kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met TYAN TYAN S1572 ATX . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
