Gebruiksaanwijzing /service van het product 41AD-280G000 van de fabrikant Yard Machines
Ga naar pagina of 22
Operator’ s Manual Curved Shaft, 2-Cycle T rimmer Model 41AD-280G000 IMPORT ANT : Read safety rules and instructions carefully befor e operating equipment.
2 T ABLE OF CONTENTS Content Page Important Safe Operation Practices .................................................................... 3-5 Assembling Y our T rimmer ...................................................................................
3 SECTION 1: IMPOR T ANT SAFE OPERA TION PRACTICES This Symbol Points Out Important Safety Information Which, If Not Followed, Could Endanger The Personal Safety And/or Property Of Y ourself And Others. Read And Follow All Instructions In This Manual Before Attempting T o Operate Y our T rimmer .
4 • This unit does not have a clutch. The cutting attachment continues to rotate when the engine is idling. T o prevent injury , have the unit adjusted by an authorized service technician. • Adjust the D-Handle to your size to provide the best grip.
5 • PRIMER BULB Push primer bulb, fully and slowly , 5 to 7 times. • UNLEADED FUEL Always use clean, fresh unleaded fuel. • OIL Refer to operator's manual for the proper type of oil. • THROWN OBJECTS CAN CAUSE SEVERE INJUR Y Do not operate unit without proper attachments and guar ds in place.
6 Figure 4 Installing and Adjusting the D-Handle NOTE: The bolt, washer and wing nut need to be removed from the D-handle before installing. 1. Push the D-handle down onto the shaft housing so that the handle slants towards the shaft grip. The squared bolt hole in the handle is to the right.
7 Figure 5 SECTION 3: KNOW Y OUR TRIMMER Primer Bulb Choke Control Air Filter/ Muffler Cover Spark Plug Muffler On/Off Stop Control STOP/OFF (O) ST ART/ON (I) Throttle Control Read this operator’ s manual and safety rules befor e operating your trimmer .
8 SECTION 4: OPERA TING Y OUR TRIMMER Oil and Gas Mixing Instructions Old and/or improperly mixed fuel ar e the main reasons for the unit not running pr operly . Be sur e to use fresh, clean unleaded fuel. Follow the instructions carefully for the pr oper fuel/oil mixture.
9 Choke Control Full Choke Position (A) Primer Bulb Starting Engine WARNING: A void accidental starting. Be in the starting position when pulling the starter rope. See Figur e 9. The operator and unit must be in a stable position while starting to avoid serious personal injury .
Each time the head is bumped, about 1 inch (25.4 mm) of trimming line is released. A blade in the cut- ting attachment shield will cut the line to the proper length if excess line is released. For best results, tap the Bump Head™ on bar e ground or har d soil.
11 Figure 12 Decorativ e T rimming Decorative trimming is accomplished by removing all vegetation around tr ees, posts, fences, etc. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground. See Figur e 12. Tips for Best T rimming Results • Keep the cutting attachment parallel to the ground.
12 SECTION 5: MAKING ADJUSTMENTS Idle Speed Screw Figure 13 Engine Specifications Engine T ype … … … … … … …Air -Cooled, 2-Cycle Displacement … … … … … … … … … … … 31cc Idle Speed R.P .M. … … … … … 3,400- 4,400 rpm Operating R.
13 WARNING: T o avoid serious personal injury , always tur n the unit off, allow it to cool and disconnect the spark plug before you clean or perform any maintenance on it. T rouble Shooting Refer to the trouble shooting chart for mor e informa- tion.
14 8. Place the air filter/muffler cover over the back of the carburetor and muf fler . NOTE: The choke control must be in the P ARTIAL choke position (B) to install the air filter/muffler cover . See Figure 14. 9. Insert the four (4) screws into the holes in the air filter/muffler cover and tighten.
15 Figure 19 Figure 22 Figure 23 Figure 24 Figure 20 Figure 21 Single Line Installation Go T o Step 8 for SplitLine™ Installation 6. T ake approximately 25 feet (7.6 m) of new trim- ming line, loop it into two equal lengths. Insert each end of the line through one of the two holes in the inner reel.
16 SECTION 7: OFF SEASON STORAGE If the unit will be stored for an extended time, 1. Drain all fuel from the fuel tank into a container . Do not use fuel that has been stored for mor e than 60 days. Dispose of the old fuel in accordance to local r egulations.
17 SECTION 8: TROUBLE SHOOTING GUIDE ENGINE WILL NOT ST ART ENGINE WILL NOT IDLE ENGINE WILL NOT ACCELERA TE ENGINE LACKS POWER OR ST ALLS WHEN UNDER LOAD CUTTING A TT ACHMENT WILL NOT ADV ANCE LINE O.
18 SECTION 9: P AR TS LIST FOR MODEL 41AD-280G000 42 1 2 3 8 10 12 3 4 5 7 6 11 13 15 16 47 48 43 14 22 49 20 17 18 19 21 26 27 28 31 32 30 33 34 36 37 38 35 25 32 39 40 46 41 44 42 45 24 29 23 9.
19 1 182059 Air Cleaner/Muffler Cover Assembly (includes 2 & 42) 2 180350 Air Cleaner Filter 3 181345 Carburetor Mounting Scr ew Assembly 4 180226 W avey W asher 5 182160 Choke Lever Assembly (inc.
20 MODEL 41AD-280G000 10 8 13 9 17 16 18 19 15 11 12 14 1 1 5 6 7 4 3 2.
21 1 182093 Throttle Housing and T rigger Assembly (includes 2 & 3) 2 610314 Throttle T rigger Spring 3 180975 Throttle T rigger 4 182068 Throttle Cable Assembly 5 145819 D-Handle Assembly 6 18158.
MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty , including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified.
Een belangrijk punt na aankoop van elk apparaat Yard Machines 41AD-280G000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Yard Machines 41AD-280G000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Yard Machines 41AD-280G000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Yard Machines 41AD-280G000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Yard Machines 41AD-280G000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Yard Machines 41AD-280G000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Yard Machines 41AD-280G000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Yard Machines 41AD-280G000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
