Gebruiksaanwijzing /service van het product AP2750 van de fabrikant 3Com
Ga naar pagina of 16
Quick Start Guide AP2750 Managed Access Point 3CRWX275075A The 3Com AP2750 Managed Access Point provides IEEE 802.11a or 802 .11b/g wireless access to the network. The access point is designed for us e with a 3Com W ireless LAN Switch, and r equires hardware installation only .
2 3Com AP2750 Managed Access Point Featur es Feature Description Power Port The access point can be powe red either via Power Over Ethernet (PoE), or by an external power supply (not included) that is plugged into the Power Port. Serial Port The serial port is not su pported.
3 Observing Safety Pr ecautions This equipment must be installed in compliance with local and national bui lding codes, regulatory restrictions, and FCC rules. For th e safety of people and equipment, only professional ne twork personnel should install the access point.
4 3 Attaching the Antennas Carefully unpack the standard deta chable antennas. Screw the antenna s on to the antenna connectors on the access point and hand-tighten them. After network star tup, you may need to adjust the ant ennas to fine-tune coverage in your area.
5 The figures below show the m ounting bracket be ing mounted to a wall, and then a cable being routed thr ough the large opening on the back of the mounting bracket. 4 Connect the Ether net cable (and p ower cable, if applicable) to the port(s) on the front of the access point.
6 T abletop Mounting T o install the access point on a flat surface such as a ta ble or desktop: 1 Remove the backing from the four rubber feet and attach th em on the bottom of the mounting bracket that is attached to the access point. 2 Place the access point on the table.
7 6 Checking th e LED Indicato rs When the access point is connected to power , LEDs indicate activity as foll ows (solid LED indicates connection; blinking LE D indicates activity): T r oubleshooting Refer to the Mobili ty System C onfiguration G uide or to the 3Com W ireless LAN Switch Reference Manual to obtain the access point status.
8 Regulatory Information The 3Com AP275 0 Managed Access Point (3CR WX275075A ) must be insta lled and used in strict accordance with the manufacturer's in struction s as describe d in the user doc umentati on that comes wit h the product. This device compli es with the fol lowing radi o frequency and sa fety standards.
9 • Increase the dist ance betwee n the equipment and the receiver • Connect the eq uipment to ou tlet on a circuit different from that to which the receiver is connected • Consult the d ealer o.
10 CANADA - INDUSTRY CANADA (IC) This devi ce complies with R SS 210 of Industry Canada. Operation i s subject to the fol lowing two conditions : (1) thi s device may not caus e interference, and (2) t his device must ac cept any int erference, incl uding inter ference that may caus e undesired operat ion of thi s device.
11 EUROPE - EU DECLARA TION OF CONFO RMITY Marking by the above symbol in dicates compl iance with th e Essential Req uirements and other relevant prov isions of the R& TTE Dire ctive of the Eur o pean Union (1 999/5/EC).
12 A copy of the sig ned Declarat ion of Confor mity can be downl oaded from the Product Suppo rt web page for the A P2750 (3CR WX275075A) at http: //www .
13 EUROPE - RESTRICTIONS FOR USE OF 2.4G HZ FREQUENCIES IN EUROPEAN COMMUNITY COUNTRIES This devi ce may be operated indoors or outdoo rs in a ll coun tries of the European C ommunity u sing th e 2.4GHz band: Ch annels 1 - 13 , except where noted below .
14 • The 5GHz radio' s AutoChan nelSelect/ SmartSel ect setting described in the user guide must always remain enabled to ens ure that automatic 5GHz channel se lection compl ies with European requirements. The current set ting for th is feature is fo und in the 5GHz Radio Confi guration W indo w as describe d in the user guide.
15 REDUCE POWER TO 25% AND RECHE CK LINK RA TE: 5 Repeat steps 3 and 4 using a "T ransmit Power" of Quarter (-6dB) and check if majority of station link rates are decr eased fr om 54Mbps. If the link rates using the -6dB setting ar e now: • lower than the maximu m possible values, the -6dB power reducti on is not necessary .
Copyright © 200 4 3Com Corporat ion. All righ ts reserved. 3Com and the 3Com logo a re registered trademarks of 3Com Co rporation . All other company and pr oduct name s may be tr ademarks of the respe ctive co mpanies wit h which th ey are a ssociated .
Een belangrijk punt na aankoop van elk apparaat 3Com AP2750 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen 3Com AP2750 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens 3Com AP2750 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding 3Com AP2750 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over 3Com AP2750 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van 3Com AP2750 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de 3Com AP2750 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met 3Com AP2750 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
