
LCD Projection TV

Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference.
Lesen Sie vor der Inbetriebnahme des Fernsehgeräts bitte den Abschnitt „Sicherheitsinformationen“ in dieser Anleitung. Bewahren Sie die Anleitung zum späteren Nachschlagen auf.
Alvorens de televisie te gebruiken, dient u de paragraaf met veiligheidsinformatie in deze handleiding te lezen. Bewaar deze handleiding zodat u deze in de toekomst kunt raadplegen.
Antes de utilizar o televisor, por favor leia a secção “Informação sobre segurança” deste manual. Guarde este manual para futuras consultas.
Bruksanvisning
NO
Før du bruker TVen, må du lese gjennom avsnittet "Sikkerhet" i denne håndboken. Ta vare på håndboken for fremtidig referanse.

For useful information about Sony products Fur hilfreiche Informationen zu Sony Produkten Voor nuttige informatie over Sony producten Para informação útil sobre os produtos Sony For nyttig informasjon om Sony produkter
© 2006 Sony Corporation
2-695-226-11(1)

Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.




1: Checking the accessories
2: Connecting an aerial/ VCR
Connecting an aerial only

Aerial Adaptor
To insert batteries into the remote



Sony strongly recommends using the TV stand SU- RG11M with a support belt designed for your TV.


P OW E R T IM E R L A M PP OW E R /S T A N D B Y 2
T V /V ID E O C A N N E L VO L U M E
1 Connect the TV to your mains socket (220-240V AC, 50Hz). 2 Press 1 on the TV (front side). When you switch on the TV for the first time, the Language menu appears on the screen. When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

3 Press F/f to select the language displayed on the menu screens, then press

After selecting the language and country/region, a message confirming the TV start auto-tuning appears on the screen. The TV will now search for and store all available TV channels.

4 Press F/f to select the country/region in which you will operate the TV, then press

If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region. The message confirming the TV start auto-tuning appears on the screen, then go to “6: Auto-tuning the TV”.
The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, please be patient and do not press any buttons on the TV or remote. If a message appears for you to confirm the aerial connections No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again. 2 When the Programme Sorting menu appears on the screen, follow the steps of “Programme Sorting” (page 25). If you do not wish to change the order in which the analogue channels are stored on the TV, go to step 3. 3 Press MENU to exit. The TV has now tuned in all the available channels.

Mains lead • Observe the followings to prevent the mains lead being damaged. If the mains lead is damaged, it may result in a fire or an electric shock. – When you disconnect the mains
lead, disconnect it from the mains socket first. – Be sure to grasp the plug when
disconnecting the mains lead. Do not pull on the mains lead itself. – Do not pinch, bend, or twist the
Mains socket Do not use a poor fitting mains socket. Insert the plug fully into the mains socket. A poor fit may cause arcing and result in a fire. Contact your electrician to have the mains socket changed.

Cleaning the mains plug Unplug the mains plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate and result in a fire.
Overloading This TV set is designed to operate on a 220–240 V AC supply only. Take care not to connect too many appliances to the same mains socket as this could result in fire or electric shock.
When not in use • If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.
Continued

items such as newspapers, etc. • Leave some space around the TV set as shown below. Otherwise, air-circulation may be inadequate and causing overheating, which may cause a fire or damage to the TV set.
Medical institutions Do not place this TV set in a place where medical equipment is in use. It may cause a malfunction of medical instruments.

P OW E R T IM E R L A M PP OW E R /S T A N D B Y
T V /V ID E O C A N N E L VO L U M E
Leave at least this much space.
Air circulation is blocked.

30 cm · 10 cm · 15 cm

Lightning storms For your own safety, do not touch any part of the TV set, mains lead, or aerial lead during lightning storms.
Servicing Dangerously high Voltage are present inside the TV set. Do not open the cabinet. Entrust the TV set to qualified service personnel only.
Small accessories removal and fittable Keep small accessories out of children’s reach.

Precautions
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.


1 "/1 – TV standby Switches off the TV temporarily and on from standby mode.
7 MENU (page 19)
8 DIGITAL – Digital mode (page 13)
qa PROG +/- (page 13)
qs 2 +/- – Volume
qd % – Mute (page 13)
qf / – Text (page 14)
qg ANALOG – Analogue mode (page 13)
qh / RETURN Returns to the previous screen of any displayed menu.
qj – EPG (Digital Electronic Programme Guide) (page 15)
qk – Picture mode (page 20)
ql 9 – Sound effect (page 21)


P OW E R T IM E R L A M PP OW E R /S T A N D B Y
T V /V ID E O C A N N E L VO L U M E
2 1 5 9 3 4 6 7 8
6 Lamp Indicator. Lights up in red when the lamp for the light source has burned out (page 33)
8 Remote control sensor
9 1 – Power Switches the TV on or off.
1 (page 19)

Watching TV
3 Press the number buttons or PROG +/- to select a TV channel. To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Digital Electronic Programme Guide (EPG), see page 15. In digital mode An information banner appears briefly. The following icons may be indicated on the banner.

P OW E R T IM E R L A M PP OW E R /S T A N D B Y
T V /V ID E O C A N N E L VO L U M E
Turn off the TV temporarily (Standby mode)
Press "/1.
Turn on the TV from Standby mode without sound
Press %. Press 2 +/- to set the volume level.
Turn off the TV Press 1 on the TV.
Adjust the volume Press 2 + (increase)/ - (decrease).
Mute the sound Press %. Press again to restore.
Access the Programme index table (in analogue mode only)
Press . To select an analogue channel, press F/f, then press
1 Press 1 on the TV (front side) to switch on the TV. When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV. 2 Press DIGITAL to switch to digital mode or ANALOG to switch to analogue mode. The channels available vary depending on the mode.
. To access the Input signal index table, see page 18.
Continued

To access Text Press /. Each time you press /, the display changes cyclically as follows: Text t Text over the TV picture (mix mode) t No Text (exit the Text service) To select a page, press the number buttons or PROG +/-. To hold a page, press / . To reveal hidden information, press / .

Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen.

Displays conventional 4:3 broadcasts (e.g., non-wide screen TV) in the correct proportions.

Picture Freeze Freezes the TV picture (e.g. to make a note of a telephone number or recipe). 1 Press on the remote control. 2 Press F/f/G/g to adjust the position of the window. 3 Press to remove the window. 4 Press again to return to normal TV mode.
Displays wide screen (16:9) broadcasts in the correct proportions.

Displays cinemascopic (letter box format) broadcasts in the correct proportions.

PIP in PC Mode (Picture in Picture) In PC mode, displays a small picture of the last channel selected. 1 Press on the remote control. 2 Press F/f/G/g to adjust the position of the window. 3 Press to cancel.
Displays 14:9 broadcasts in the correct proportions. As a result, black border areas are visible on the screen.
To change the screen mode manually to suit the broadcast Press repeatedly to select Smart, 4:3, Wide, Zoom, or 14:9.

1 In digital mode, press to display the Digital Electronic Programme Guide (EPG). 2 Perform the desired operation, as shown in the following table.
Turn off the EPG Press .
Move through the EPG Press F/f/G/g.
Watch a current programme Press while the current programme is selected.
Sort the programme information by category – Category list
1 Press the blue button. 2 Press F/f/G/g to select a category. The category name is displayed on the side. The categories available include: “Favourite”: Contains all the channels that have been stored in the Favourite list (page 17). “All Categories”: Contains all available channels. “News”: Contains all news channels. 3 Press . The Digital Electronic Programme Guide (EPG) now only displays the current programmes from the category selected.
Set a programme to be recorded – Timer REC
Continued

1 Press F/f/G/g to select the future programme you want to display. 2 Press . 3 Press F/f to select “Reminder”. 4 Press to automatically display the selected programme when the programme starts. A c symbol appears by that programme’s information. Note If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start.
Set a programme to be displayed automatically on the screen when it starts – Reminder
Set the time and date of a programme you want to record – Manual timer REC
Cancel a recording/reminder – Timer list 1 Press . 2 Press F/f to select “Timer list”. 3 Press F/f to select the programme you want to cancel, then press . A display appears to confirm that you want to cancel the programme. 4 Press g to select “Yes”, then press to confirm.

The Favourite feature allows you to select programs from a list of up to 8 channels you specify. To display the Favourite list, see “Navigating through menus” (page 19).

Create your Favourite list for the first time A message appears asking if you want to add channels to the Favourite list when you select “Digital Favourites” in the “MENU” for the first time. 1 Press to select “Yes”. 2 Press F/f to select the channel you want to add. If you know the channel number, you can use the number buttons to directly select a channel. 3 Press . Channels that are stored in the Favourite list are indicated by a symbol.
Turn off the Favourite list Press RETURN.
See brief details on current programmes Press while selecting a channel. Press again to cancel.

1 Press the blue button. Channels that are stored in the Favourite list are indicated by a symbol. 2 Press F/f to select the channel you want to add or remove. If you know the channel number, you can use the number buttons to directly select a channel. 3 Press . 4 Press the blue button to return to the Favourite list.
Remove all channels from the Favourite list 1 Press the blue button. 2 Press the yellow button. A display appears to confirm that you want to delete all channels from the Favourite list. 3 Press G to select “Yes”, then press to confirm.
Favourite list

Viewing pictures from connected equipment
Access the Input signal index table
Press to access the Input signal index table. (Then, only in analogue mode, press g.) To select an input source, press F/f, then press .
Switch on the connected equipment, then perform one of the following operation.
For equipment connected to the scart sockets using a fully-wired 21-pin scart lead Start playback on the connected equipment. The picture from the connected equipment appears on the screen.
For an auto-tuned VCR (page 4) In analogue mode, press PROG +/-, or the number buttons, to select the video channel.
For other connected equipment Press / repeatedly until the correct input symbol (see below) appears on the screen.
AV1/ AV1, AV2/ AV2: Audio/video or RGB input signal through the scart socket / 1 or 2. appears only if an RGB source has been connected.
AV3: Component input signal through the Y, PB/CB, PR/CR sockets / 3, and audio input signal through the L, R sockets / 3.

AV4/ AV4: Video input signal through the video socket 4, and audio input signal through the L (MONO), R audio sockets 4. appears only if the equipment is connected to the S video socket 4 instead of the video socket 4, and S video input signal is input through the S video socket 4.
AV6/ AV7: Digital audio/video signal is input through the HDMI IN 6 socket. Audio input signal is analogue only if the equipment has been connected using the DVI and audio out socket.
Return to the normal TV operation
Press DIGITAL or ANALOG.

Navigating through menus
“MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or external inputs with the remote. Also, settings for your TV can be changed easily using “MENU”.
1 Press MENU to display the menu.
2 Press F/f to select an option. 3 Press to confirm a selected option. To exit the menu, press MENU.
Digital Favourites (in digital mode only)
Launches the Favourite list. For details about settings, see page 17.
Programme List (in analogue mode only)
Analogue (in digital mode only)
Returns to the last viewed analogue channel.
Digital (in digital mode only)
Returns to the last viewed digital channel.
Digital EPG (in digital mode only)
Launches the Digital Electronic Programme Guide (EPG). For details about settings, see page 15.
Settings Opens the Settings menu screen where most of advanced settings and adjustments are performed. Select a menu icon, select an option and make the desired change or adjustment using F/f/G/g. For details about settings, see page 20 to 29.
Digital Favourites

You can select the options listed below on the Picture menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Picture Mode Contras Brightness Colour Hue Sharpness Colour Tone Reset Noise Reduction Iris
Contrast Increases or decreases picture contrast.
Brightness Brightens or darkens the picture.
Colour Increases or decreases colour intensity.
Hue Increases or decreases the green tones. Tip “Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).
Sharpness Sharpens or softens the picture.
Reset Resets all picture settings except “Picture Mode” to the factory settings.
Iris Enhances the contrast for dark scenes.

You can select the options listed below on the Sound menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Treble Adjusts higher-pitched sounds.
Bass Adjusts lower-pitched sounds.
Balance Emphasizes left or right speaker balance.
Reset Resets all the sound settings to the factory settings.
Auto Volume Keeps a constant volume level even when volume level gaps occur (e.g., adverts tend to be louder than programmes).
Continued

TV Speakers Turns off the TV speakers e.g. to listen to the sound through external audio equipment connected to the TV.

You can select the options listed below on the Features menu. To select options in “Settings”, see “Navigating through menus” (page 19).

RGB Center Adjusts the horizontal picture position so that the picture is in the middle of the screen.
This option is only available if an RGB source has been connected to the Scarts connectors
1/ 1 or 2/ 2 on the rear of the TV.
PC Adjustment Customizes the TV screen as a PC monitor.
Continued

Timer Sets the timer to turn on/off the TV.

You can select the options listed below on the Set-up menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Auto Start-up Starts the “first time operation menu” to select the language and country/region, and tune in all available digital and analogue channels. Usually, you do not need to do this operation because the language and country/region will have been selected and channels already tuned when the TV was first installed (page 5, 6). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).
Language Selects the language in which the menus are displayed.
Country Selects the country/region where you operate the TV. Tip The country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region.
Auto Tuning Tunes in all the available analogue channels. Usually you do not need to do this operation because the channels are already tuned when the TV was first installed (page 5, 6). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).
Programme Sorting Changes the order in which the analogue channels are stored on the TV. 1 Press F/f to select the channel you want to move to a new position, then press g. 2 Press F/f to select the new position for your channel, then press .
Sound Offset Sets an independent volume level to each equipment connected to the TV.
Continued

Before selecting “Label”/“AFT”/“Audio Filter”/“Skip”/“Decoder”, press F/f to select the programme number you want to modify. Then, press .
System/Channel Presets programme channels manually. 1 Press F/f to select “System”, then press . 2 Press F/f to select one of the following TV broadcast systems, then press G. B/G: For western European countries/regions D/K: For eastern European countries/regions L: For France I: For the United Kingdom Note
Depending on the country/region selected for “Country” (page 5), this option may not be available. 3 Press F/f to select “Channel”, then press . 4 Press F/f to select “S” (for cable channels) or “C” (for terrestrial channels), then press g. 5 Tune the channels as follows:
If you do not know the channel number (frequency) Press F/f to search for the next available channel. When a channel has been found, the search will stop. To continue searching, press F/f.
If you know the channel number (frequency) Press the number buttons to enter the channel number of the broadcast you want or your VCR channel number. 6 Press to jump to “Confirm”, then press . 7 Press f to select “OK”, then press . Repeat the procedure above to preset other channels manually.
Label Assigns a name of your choice, up to five letters or numbers, to the selected channel. This name will be displayed briefly on the screen when the channel is selected.
AFT Allows you to fine-tune the selected programme number manually if you feel that a slight tuning adjustment will improve the picture quality. You can adjust the fine tuning over a range of -15 to +15. When “On” is selected, the fine tuning is performed automatically.

Skip Skips unused analogue channels when you press PROG +/- to select channels. (You can still select a skipped channel using the number buttons.)
Decoder Views and records the scrambled channel selected when using a decoder connected directly to scart connector / 1, or to scart connector / 2 via a VCR. Note Depending on the country/region selected for “Country” (page 5), this option may not be available.
Confirm Saves changes made to the “Manual Programme Preset” settings.

You can change/set the digital settings using the Digital Set-up menu. To select options in “Settings”, see “Navigating through menus” (page 19).

Digital Tuning Displays the “Digital Tuning” menu.
Digital Auto Tuning Tunes in all the available digital channels. Usually you do not need to do this operation because the channels are already tuned when the TV was first installed (page 5). However, this option allows you to repeat the process (e.g., to retune the TV after moving house, or to search for new channels that have been launched by broadcasters).
Programme List Edit Removes any unwanted digital channels stored on the TV, and changes the order of the digital channels stored on the TV. 1 Press F/f to select the channel you want to remove or move to a new position. If you know the programme number (frequency) Press the number buttons to enter the three-digit programme number of the broadcast you want. 2 Remove or change the order of the digital channels as follows: To remove the digital channel Press . A message that confirms whether the selected digital channel is to be deleted appears. Press G to select “Yes”, then press . To change the order of the digital channels Press g, then press F/f to select the new position for the channel and press G. Repeat the procedure in steps 1 and 2 to move other channels if required. 3 Press RETURN.
Digital Manual Tuning Tunes the digital channels manually. 1 Press the number button to select the channel number you want to manually tune, then press F/f to tune the channel. 2 When the available channels are found, press F/f to select the channel you want to store, then press . 3 Press F/f to select the programme number where you want to store the new channel, then press . Repeat the procedure above to tune other channels manually.

Digital Set-up Displays the “Digital Set-up” menu.
Subtitle Setting Displays digital subtitles on the screen. When “For Hard Of Hearing” is selected, some visual aids may also be displayed with the subtitles (if TV channels broadcast such information).
Subtitle Language Selects which language subtitles are displayed in.
Audio Language Selects the language used for a programme. Some digital channels may broadcast several audio languages for a programme.
Audio Type Increases the sound level when “For Hard Of Hearing” is selected.
Parental Lock Sets an age restriction for programmes. Any programme that exceeds the age restriction can only be watched after a PIN Code is entered correctly. 1 Press the number buttons to enter your existing PIN code. If you have not previously set a PIN, a PIN code entry screen appears. Follow the instruction of “PIN Code” below. 2 Press F/f to select the age restriction or “None” (for unrestricted watching), then press . 3 Press RETURN.
PIN Code Sets a PIN code for the first time, or allows you to change your PIN code. 1 Enter a PIN as follows: If you have previously set a PIN Press the number buttons to enter your existing PIN. If you have not set a PIN Press the number buttons to enter the factory setting PIN of 9999. 2 Press the number buttons to enter the new PIN code. A message appears to inform you that the new PIN has been accepted. 3 Press RETURN. Tip PIN code 9999 is always accepted.
Technical Set-up Displays the Technical Set-up menu. “Auto Service Update”: Enables the TV to detect and store new digital services as they become available. “Software Download”: Enables the TV to automatically receive software updates, free through your existing aerial (when issued). Sony recommends that this option is set to “On” at all times. If you do not want your software to be updated, set this option to “Off”. “System Information”: Displays the current software version and the signal level. “Time Zone”: Allows you to select the correct time zone for your country.
CA Module Set-up Allows you to access a Pay Per View service once you obtain a Conditional Access Module (CAM) and a view card. See page 30 for the location of the (PCMCIA) socket.

Connecting optional equipment
You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.


Conditional Access Module (CAM) C
To use Pay Per View services. For details, refer to the instruction manual supplied with your CAM. To use the CAM, remove the rubber cover from the CAM slot. Switch off the TV when inserting your CAM into the CAM slot. When you do not use the CAM, we recommend that you replace the cover on the CAM slot.
S VHS/Hi8/DVC camcorder A
Connect to the S video socket
4 or the video socket 4, and the audio sockets 4. To avoid picture noise, do not connect the camcorder to the video socket
4 and the S video socket 4 at the same time. If you connect mono equipment, connect to the L socket 4, and set “Dual Sound” to “A” (page 21).
Headphones B Connect to the i socket to listen to sound from the TV on headphones.

PC D Connect to the PC / sockets. It is recommended to use a PC cable with ferrites.

Digital satellite receiver or DVD player E, F
DVD player with component output G
Connect to the component sockets and the audio sockets / 3.
Video game equipment, DVD player or decoder H
Connect to the scart socket / 1. When you connect the decoder, the scrambled signal from the TV tuner is output to the decoder, then the unscrambled signal is output from the decoder.
DVD recorder or VCR that supports SmartLink I
Connect to the scart socket / 2. SmartLink is a direct link between the TV and a VCR/DVD recorder.
Hi-Fi audio equipment J
Connect to the audio output sockets to listen to the sound from the TV on Hi-Fi audio equipment.
Digital satellite receiver · Hi-Fi · Decoder

Optimum Viewing Area
For the best picture quality, try to position the TV set so that you can view the screen from within the areas shown below.



The projection lamp, like all lamps, will eventually lose brightness and functionality which affects the overall performance of your TV. How long the lamp maintains its brightness will vary depending upon your usage and environmental conditions. To maintain the quality of your viewing experience, Sony recommends that you replace the lamp (1) after approximately 8,000 hours of use, (2) when the screen becomes dark or the colour looks unusual, (3) when the LAMP LED on the front of the TV lights on in red.
1 Turn off the power and disconnect the power cord. If you start changing the lamp without disconnecting the power cord, the standby indicator on the TV set flashes. Disconnect the power cord to continue changing the lamp. 2 Replace the lamp 30 minutes or more after the power is turned off to allow it to cool. 3 Take the new lamp out of the box.
Do not touch the glass portion of the new lamp.

Continued

5 Remove the lamp door.

Turn the knob counterclockwise to OPEN and pull out the cover.
6 Pull out the lamp.
Hook a finger through the loop of the lamp handle and pull the handle upwards. Then pull the lamp straight out..

7 Put the new lamp into its place.
Mount the new lamp securely. Failure to do so may cause a fire or the screen to go dark.


8 Reattach the lamp door.
Turn the knob back to CLOSE and secure the cover.

9 Put the outside lamp cover back in its place.

Display Unit Power Requirements:
220–240 V AC, 50 Hz Screen Size:
50 inches Display Resolution (horizontal x vertical):
1280 dots x 720 lines Power Consumption:
175 W Standby Power Consumption:
1 W or less Dimensions (w × h × d):
Approx. 1184 x 827 x 408 mm Weight:
Approx.29,5 kg
Panel System LCD (Liquid Crystal Display) Panel
B/G/H, D/K, L, I. Digital: DVB-T.
Colour/Video System Analogue: PAL, SECAM.
48 kHz, 16, 20 and 24 bits. • AV7: 7 HDMI: Video: 480i, 576i, 480p, 576p, 720p, 1080i
NTSC 3.58, 4.43 (only Video In) Digital: MPEG-2 MP@ML
Aerial 75 ohm external terminal for VHF/UHF
48 kHz, 16, 20 and 24 bits. AUDIO:500 mVrms (100% modulation)
Channel Coverage Analogue: VHF: E2–E12 UHF: E21–E69 CATV: S1–S20 HYPER: S21–S41 D/K: R1–R12, R21–R69 L: F2–F10, B–Q, F21–F69 I: UHF B21–B69 Digital: VHF/UHF
Sound Output 10 W +10 W (RMS)
Design and specifications are subject to change without notice.

Input signal frequency: Horizontal: 31,4 - 48,4 KHz. Vertical: 59 - 61 Hz. Maximum Resolution: 1024 dots x -768 lines.
Nº Resolution Graphic mode Horizontal Vertical (dots x lines) frequency (kHz) frequency (Hz)
1 640 x 480 VESA 60 31.469 59.940
2 800 x 600 VESA 60 37.879 60.317
3 1024 x 768 VESA 60 48.363 60.004
This TV does not support Sync on Green or Composite Sync. If a signal other than in the above chart is input, it may not be displayed properly or may not be displayed as you set. Using the Vertical frequency (Hz) of the personal computer at 60 is recommended.

Check whether the 1 (standby) indicator is flashing in red.
When it is flashing The self-diagnosis function is activated. 1 Measure how long the 1 (standby) indicator flashes and stops flashing. For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds. 2 Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (duration and interval).
When it is not flashing 1 Check the items in the tables below. 2 If the problem still persists, have your TV serviced by qualified service personnel.
No picture (screen is dark) and no sound
No picture or no menu information from equipment connected to the scarts or HDMI IN socket
Only snow and noise appear on the screen
Distorted picture (dotted lines or stripes)
Picture noise when viewing a TV channel
Some tiny black points and/or bright points on the screen
No colour on programmes • Select “Reset” in the “Picture Adjustment” menu to return to the factory settings (page 20).
No colour or irregular colour when viewing a signal from the Y, PB/CB, PR/CR jacks of 3

Irregular picture when viewing a signal from PC
Noisy sound • See the “Picture noise” causes/remedies on page 38.
The desired channel cannot be selected
General
The TV turns off automatically (the TV enters standby mode)
The TV turns on automatically • Check if the “On Time” is activated (page 24).
Some input sources cannot be selected
The remote does not function • Replace the batteries.
The lamp indicator on front of the TV set is lit.


Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.
Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.