Gebruiksaanwijzing /service van het product SV8PRO van de fabrikant Adder Technology
Ga naar pagina of 44
SMAR T V V i i e e w w PR O I N S T A L L A T I O N & U S E www .addertec.com 16 P ort SMAR T Vie w PR O SV16PR O 12 P ort SMAR T Vie w PR O SV12PR O 8 P ort SMAR T Vie w PR O SV8PR O 4 P ort SMAR.
SmartView Installation a nd Use Page 1 About this manual SmartView Pro - Installation and Use Fifth edition (March 1999) Part No. ADD0031/5 (c) 1999 Adder Technology Ltd. All rights reserved. Whilst every precaution has been taken in the preparation of this manual, Adder Technology Ltd assumes no responsibility for errors or omissions.
SmartView Installation a nd Use Page 2 Radio Frequency Energy Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances.
SmartView Installation and Use Page 3 Contents 1. Introduction .................................................................................... 5 1.1 Key features ....................................................................................
SmartView Installation and Use Page 4 4. SmartView configuration options ................................................ 30 4.1 Screen saver time delay ........................................................................ 30 4.2 Autoscan lock on mode and delay time .
SmartView Installation and Use Page 5 1. Introduction Thank you for purchasing the Adder SmartView Pro. Your SmartView Pro is a high performance keyboard, monitor and mouse sharing device which supports a wide range of PC hardware and software platforms.
SmartView Installation and Use Page 6 1.2 Package contents SmartView Pro. Power supply suitable for your country. 6 x stick on self-adhesive rubber feet. 2 x mounting brackets for fixing the unit into a 19 inch rack. 4 x screws for fixing mounting brackets to SmartView Pro (6 screws supplied with SV12PRO and SV16PRO models) This installation guide.
SmartView Installation and Use Page 7 1.3 Product information Fig. 1 - SmartView SV8PRO Fig. 2 - Remote control pad / display (optional accessory for 4 & 8 port models).
SmartView Installation and Use Page 8 Fig. 3 - SmartView SV4PRO.
SmartView Installation and Use Page 9 Fig. 4 - SmartView SV12PRO.
SmartView Installation and Use Page 10 Fig. 5 - SmartView SV16PRO.
SmartView Installation and Use Page 11 2. Installation 2.1 What you will need Cables to connect the SmartView to each of your PC keyboard, video and mouse ports. Cable specifications are given in appendix A. (You do not need to connect a mouse cable if you are not using the mouse).
SmartView Installation and Use Page 12 2.2 Mounting the SmartView The SmartView has been designed to be used either on a desktop or mounted in a 19 inch rack. If the SmartView is to be used on a desktop then you will need to stick the supplied self-adhesive rubber feet to the underside of the SmartView.
SmartView Installation and Use Page 13 2.4 Configuring your PCs Configure your PC in the same way that you would if your keyboard, mouse and monitor were all connected directly to your PC, but bearing.
SmartView Installation and Use Page 14 For example: to set hotkey option 2 type the following at the 'C' prompt (at SmartView 'C' prompt) H H 2 2 f f To exit configure mode type: E E f f 2.6 Summary of SmartView configuration options Full details of each of the configuration options and their uses are given in section 4.
SmartView Installation and Use Page 15 S1 - 2 seconds of inactivity before allowing switchover between A & B ports (default) S2 - 5 seconds of inactivity before allowing switchover between A &.
SmartView Installation and Use Page 16 F1 - Display firmware first digit F2 - Display firmware second digit F3 - Display firmware third digit F5 - Restore PS/2 mouse function F6 - Restore IntelliMouse function F8 - RESET all configurations to default settings.
SmartView Installation and Use Page 17 2.8 Re-enabling a disconnected PS/2 mouse If you disconnect the shared PS/2 mouse from the SmartView by accident during operation then the mouse operation will be lost when the mouse is plugged back in.
SmartView Installation and Use Page 18 Standard PS/2 mouse data uses a different data format to IntelliMouse data and so two reset functions are provided on the SmartView. The type of data format expected by the PC depends upon the driver and the type of mouse that was connected when the driver was booted.
SmartView Installation and Use Page 19 3. Using the SmartView This section explains the general operation of the SmartView. We recommend that you read this section before starting to use the product. 3.1 Power on status At power on the SmartView selects PC number 1 and displays '1'.
SmartView Installation and Use Page 20 The SELECT key can also be used to access the SmartView’s configuration mode (see section 2.5). To do this press the key and hold it down for 5 seconds until ‘C’ appears on the SmartView’s front panel display.
SmartView Installation and Use Page 21 3.4 Status display The status display usually shows the currently selected port. If autoscan mode is selected, the segments will illuminate in sequence in a clockwise direction interspersed with a display of the currently selected channel.
SmartView Installation and Use Page 22 3.5 Using the dual control ports (A and B) The SmartView is fitted with two control ports, A and B. Each control port has a keyboard, mouse and monitor connection. Either control port may be used to access the SmartView.
SmartView Installation and Use Page 23 ‘HOTKEYs’ and ‘9’ - selects channel 9 (12 & 16 port models only) ‘HOTKEYs’ and ‘1 then 0’ - selects channel 10 (12 & 16 port models only).
SmartView Installation and Use Page 24 Examples of common hotkey sequences (assuming CTRL + ALT hotkey option): To select channel 2: press ba ba 2 2 release 2 2 ba ba To 'tab through' channe.
SmartView Installation and Use Page 25 On-Screen menu (models SV4PRO and SV8PRO) Port numbers are entered as single digits On-Screen menu (models SV12PRO and SV16PRO) Port numbers are entered as double digits with leading zeros where required Adding a computer to the menu list With the menu visible on the screen, press the INSERT key.
SmartView Installation and Use Page 26 entry field and you can enter the port number for the named Computer. Port numbers are specified using single digits on the 4 and 8 port models and double digits on the 12 and 16 port models (adding a leading 0 if necessary).
SmartView Installation and Use Page 27 Summary of keys used by the menu and their function ‘HOTKEYs’ and ‘M’ - calls the menu up onto the screen (even if no PC video exists) ‘INSERT’ - add.
SmartView Installation and Use Page 28 names. The On Screen Menu is recommended for selecting computers on cascaded SmartViews as this avoids the need to use long hotkey sequences that may be hard to remember. When using the On Screen Menu, limit the cascade depth to three levels (the maximum number of port digits that can be added to the menu).
SmartView Installation and Use Page 29 A typical cascade of two SmartViews.
SmartView Installation and Use Page 30 4. SmartView configuration options All the options described in this section are entered in SmartView configure mode - see section 2.
SmartView Installation and Use Page 31 L1 - SmartView only locks on to active ports during autoscanning (default) L2 - SmartView locks on to every port in turn during autoscanning L3 - SmartView power.
SmartView Installation and Use Page 32 S1 - 2 seconds of inactivity before allowing switchover between A & B ports (default) S2 - 5 seconds of inactivity before allowing switchover between A &.
SmartView Installation and Use Page 33 U1 - SmartView channels are switchable using a 3 button mouse or IntelliMouse (default) (SmartView reports 2 button mouse mode to PCs) U2 - SmartView channels ar.
SmartView Installation and Use Page 34 4.6 Firmware functions (version query, mouse restore and reset) For technical support purposes, it may be necessary to find the firmware release version for the control software in your SmartView. For example, if the release version is v1.
SmartView Installation and Use Page 35 4.8 Setting a security password There are many situations where unrestricted access to corporate file servers or sensitive information needs to be controlled. In such circumstances, the SmartView can be locked away in a room or secure cabinet and controlled remotely.
SmartView Installation and Use Page 36 4.9 Cascade query code The SmartViews use a special ‘query code’ to detect whether or not they are connected to another SmartView. By default your SmartView Pro uses query code AD. SmartView Pro units with firmware versions less than 1.
SmartView Installation and Use Page 37 Appendix A. Cable and connector specifications IMPORTANT NOTE The maximum cable lengths supported vary widely between devices and cables. It may be possible to use cables that are longer than those specified below with certain PCs and peripherals but this cannot be guaranteed.
SmartView Installation and Use Page 38 RS232 serial mice - these require a special converter to connect the RS232 lines present on the SmartView mouse ports to the RS232 port on a PC.
SmartView Installation and Use Page 39 Appendix B. Problem Solving Problem: Poor video quality with smearing fuzziness or ripple. Action: Use screened coaxial video cables to connect your devices to the SmartView. Problem: Mouse does not move cursor on screen.
SmartView Installation and Use Page 40 Problem: Mouse causes channel to change. Action: Some cheaper mice are not fully compatible with the SmartView and can lose data causing the channel to be changed (if mouse switching of channels is enabled).
SmartView Installation and Use Page 41 Problem: Video appears to be lost after a PC has gone into auto power down mode. Moving the mouse and typing at the keyboard does not wake it up. Action: Some computers tested output an incomplete video signal in auto power down mode.
SmartView Installation and Use Page 42 Notes.
SMAR T V V i i e e w w PR O INST ALLA TION & USE ADDER T echnology Limited T echnolog y House T rafalgar W a y Bar Hill Cambridge CB3 8SQ • England T : +44 (0) 1954 780044 F: +44 (0) 1954 780081 sales@addertec .com www .adder tec.com SV -PR O-05.
Een belangrijk punt na aankoop van elk apparaat Adder Technology SV8PRO (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Adder Technology SV8PRO heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Adder Technology SV8PRO vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Adder Technology SV8PRO leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Adder Technology SV8PRO krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Adder Technology SV8PRO bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Adder Technology SV8PRO kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Adder Technology SV8PRO . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
