Gebruiksaanwijzing /service van het product 5000 Series van de fabrikant ADTRAN
Ga naar pagina of 1200
ADTRAN OPERATING SYSTEM (AOS) Command Reference Guide AOS V ersion 1 1.1 NetV ant a 5000 Series Product s November 2005 61200990L1-35E.
Command Refere nce Guide 61200990L1-35E Copyright © 2005 ADTRAN 2 T rademarks Any brand names an d product names included in this manual are trademarks, registered trademarks, service marks, or trade names of their respective holders. T o the Holde r of this Manual The content s of this manual are current as o f the da te of publication.
Command Refere nce Guide 61200990L1-35E Copyright © 2005 ADTRAN 3 W arranty and Customer Service ADTRAN will repair and return this prod uct within the warranty period if it does not meet its published specifications or fails while in service. W arra nty information can be found at www .
Command Refere nce Guide 61200990L1-35E Copyright © 2005 ADTRAN 4 Pre-Sales Inquiries an d Applications Support Y our reseller should serve as the firs t point of contact for support.
Command Refere nce Guide 61200990L1-35E Copyright © 2005 ADTRAN 5 Tr a i n i n g The Enterprise Network (EN) T echnical T raining Departme nt of fers training on our most popular p roducts. These courses include overviews on product features and functions while covering applications of ADTRAN's product lines.
Command Refere nce Guide Table of Conte n ts 61200990L1-35E Copyright © 2005 ADTRAN 6 T able of Contents Basic Mode Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Common Commands .
Command Refere nce Guide Table of Conte n ts 61200990L1-35E Copyright © 2005 ADTRAN 7 TACACS+ Group Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191 Index . . . . . . . . . . . . . . . . . . . . .
Command Refere nce Guide CLI Introduction 61200990L1-35E Copyright © 2005 ADTRAN 8 REFERENCE GUIDE INTRODUCTION This manual provides information about the commands that ar e available with all of the NetVanta Seri es units. This manual provides informati on ab out the commands that are availabl e with NetVanta 5000 Series units.
Command Refere nce Guide Understanding Command Security Leve ls 61200990L1-35E Copyright © 2005 ADTRAN 9 Underst a nding Command Security Levels The ADTRAN CLI has two comm and security levels — Basic and Enable . Both levels support a specific set of commands.
Command Refere nce Guide Using CLI Shortcuts 61200990L1-35E Copyright © 2005 ADTRAN 10 Using CLI Shortcut s The ADTRAN CLI provides sev eral shortcuts which h e lp you configure y our AOS product more easily. See the following table for descriptions.
Command Refere nce Guide Using CLI Shortcuts 61200990L1-35E Copyright © 2005 ADTRAN 11 ? The ADTRAN CLI contains help to gu ide you through the configuration process. Using the question mark, do any of the following: • Display a list of all subcommands in the current mode.
Command Refere nce Guide Performing Commo n CLI Functions 61200990L1-35E Copyright © 2005 ADTRAN 12 Performing Common CLI Functions The following table contains descr iptions of common CLI commands.
Command Refere nce Guide Understanding CLI Error Messages 61200990L1-35E Copyright © 2005 ADTRAN 13 Underst andin g CLI Error Messages The following table lists and defines some of th e more common error m essages given in the CLI .
Command Refere nce Guide Command Descriptions 61200990L1-35E Copyright © 2005 ADTRAN 14 COMMAND DESCRIPTIONS This portion of the guide provides a detailed listing of all availabl e commands for the ADTRAN OS CLI (organized by command set).
Command Refere nce Guide Command Descriptions 61200990L1-35E Copyright © 2005 ADTRAN 15 BGP Neighbor Configuration Co mmand Set on page 1095 Community List Command Set on page 1111 Router (OSPF) Conf.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 16 B ASIC M ODE C OMMAND S ET To activate the Basic mode, simply log in to t h e un it.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 17 enable Use the enable command (at the Basic Command mode prompt ) to enter the Enable Command mode. Use the disable command to exit the Enable Command mode. Refer to Enable Mode Comma nd Set on page 36 for more information.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 18 logout Use the logout command to terminate the current sess i on a nd return to the login scree n. Synt ax Description No subcommands. Default V alues No default s necessary for this command.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 19 ping <address> Use the ping command (at the Basic Command mode prompt) to verify In ternet Protocol (IP) network connectivity. Synt ax Description <address> S pecifies the IP address of th e system to ping.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 20 The following is a list of availab le extend ed ping fields with descriptions: T arget IP address S pecifies the IP address of the system to ping. Repeat Count S pecifies the number of ping pa ckets to send to the system (valid range: 1 to 1,000,000).
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 21 show clock Use the show c lock command to display th e system time and date entered using the clock set command. Refer to the section clock set <time> <day> <month> <year> on page 7 8 for more information.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 22 show snmp Use the show snmp command to display the system S imple Network Management Protocol (SNMP) parameters and current status of SNMP communications. Synt ax Description No subcommands.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 23 show version Use the show version command to display the current AOS version information. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 24 telnet <address> Use the telnet command to open a Telnet session (through th e AOS) to another s ystem on the network. Synt ax Description <address> S pec ifies the IP address of the remote system.
Command Refere nce Guide Basic Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 25 traceroute <address> Use the traceroute command to display the Internet Protocol (IP) routes a packet takes to reach the specified destination. Synt ax Description <address> S pecifies the IP address of the remote system to trace the routes to.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 26 C OMMON C OMMANDS The following section contains desc riptions of commands that are common across multiple command sets. These commands are listed in alphabetical order.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 27 alias <“text”> Use the alias command to populate the ifAlias O ID (Interface Table MIB of RFC2863) for all physica l and virtual interfaces when using Simple Network Mana gement Protocol (SNMP) management stations.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 28 cross-conne ct <#> <from interface> <slot/port> <tdm-group#> <to interface> <slot/port> Use the cross-connect command to create a cross-connect map fro m a created TDM group on an interface to a virtual interface.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 29 Usage Examples The following example creates a Frame Relay endpoint and connects it to th e T1 1/1 physical interface: 1.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 30 S tep 2: Create the sub-interface and configure the PVC parameters. Using the sub-interface, apply access policies to the interface, create bridging interfaces, configure di al-backup, assign an IP address, and set the PVC data-link control identifier (DLCI).
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 31 description <text> Use the description command to ide ntify the specified interfa ce (for example, circuit ID, contact information, etc.). Synt ax Description <text> Identifies the specified interface using up to 80 alph anumeric characters.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 32 do Use the do command to execute a ny AOS command, regard less of the active configuration mode. It provides a way to execute co mmands in o ther modes w ithout taking the time to exit the current mode and enter the desired one.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 33 end Use the end command to exit the current configuration mode and enter the Enable Security mode. Synt ax Description No subcommands. Default V alues No default s necessary for this command.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 34 exit Use the exit command to exit the current configuration mode and enter the previous one. For example, using the exit command in an interface conf iguration mode will activate th e Global Configuration mode.
Command Refere nce Guide Common Commands 61200990L1-35E Copyright © 2005 ADTRAN 35 shut down Use the shutdown command to disable the interface (both physi cal and virtual) so that no data will be passed through. Use the no form of this command to turn on th e interface and allow it to pass data.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 36 E NABLE M ODE C OMMAND S ET To activate the Enab le mode, enter the enable command at the Basic mode prompt. (If an enable password has been configured, a password prompt will display.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 37 sip check-sync on page 274 telnet <address> on page 275 terminal length <text> on page 276 trace.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 38 clear access-list <listname> Use the clear access-list command to clea r all counters associated with all access lists (or a specified access list). Synt ax Description <listname> Optional .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 39 clear arp-cache Use the clear arp-cache command to remove all dynamic entri es from the Address Re solution Protoc ol (ARP) cache table. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 40 clear arp-entry <address> Use the clear arp-entry command to remove a single entry from the Address Resolution Protocol (ARP) cache. Synt ax Description <address> S pecif ies the IP address of th e entry to r emove.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 41 clear bridge <group#> Use the clear bridge comma nd to clear all counters associated with bridging (or for a specified bridge-group). Synt ax Description <group#> Optional.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 42 clear buffers max-used Use the clear buffers max-used command to clear the maximum-used st atistics for buffers displayed in the show memory heap command. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 43 clear counters [ <interface> <interface id> ] Use the clear counters command to clear all interface counters (or the counters for a specified interface).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 44 clear crypto ike sa <policy priority> Use the clear crypto ike sa command to clea r existing IKE security associations (SAs), including active ones. Synt ax Description <policy priority> Optional.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 45 clear crypto ip sec sa Use the clear crypto ipsec sa command to clear existing IPSe c secur ity as sociations (SAs), including active ones.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 46 Usage Examples The following example clears all IPSec SAs: > enable # clear crypto ipsec sa The following example clears the IPSec SA used for ESP traffic wi th the SPI of 300 to IP address 63.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 47 clear dump-core The clear dump-core command clears diagnostic informa tion appended to the output of the show version command. This information results from an unexpected unit reboot.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 48 clear event-history Use the clear event-history command to clear all messages logg ed to the local event-history. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 49 clear host [ * | <hostname> ] Use the clear host command to clear a hostname when using the Domain Naming System (DNS) proxy. Synt ax Description * Clears all dynamic hosts.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 50 clear ip bgp [* | <as-number> | <ip address> ] [in | out | sof t] Use the clear ip bgp command to clear BGP ne ighbors as specified. Synt ax Description * Clears all BGP neighbors.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 51 Usage Examples The following example causes a ha rd reset with peers with an AS number of 101: > enable #.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 52 clear ip cache Use the clear ip cache command to delete cac he table entries. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 53 clear ip dhcp-server binding [ * | <ip address> ] Use the clear ip dhcp-server binding command to clear Dynamic Host Configuration Protocol (DHCP) server binding entries from the database.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 54 clear ip igmp group [ <group-address> | <interface> ] Use the clear ip igmp group command to clear entries from the In ternet Group Management Proto col (IGMP) tables.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 55 00:00:14 00:02:45 1.1.1.2 172.1.1.1 Loopback100 01:22:59 00:02:46 172.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 56 clear ip osp f [process | redistribution] Use the clear ip ospf command to reset open shortest path first (OSPF) information. Synt ax Description process Rest arts the OSPF process.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 57 clear ip policy-sessions Use the clear ip policy-sessions command to clear policy class sessions. You may clear all the sessions or a specific session. Use the show ip policy-sessions command to view a current session listing.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 58 Command History Release 2.1 Command was introdu ced. Functional Notes The second half of this command, beginning with the sour ce IP address may be copi ed and p asted from a row in the show ip policy-sessions table for easier use.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 59 clear ip policy-st ats <classname> entry <policy class #> Use the clear ip policy-stats command to clear statistical counters for policy class es. Synt ax Description <classname> Optional.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 60 clear ip prefix-list <listname> Use the clear ip prefix-list command to clear the IP prefix list hit count shown in the show ip prefix-list detail command output.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 61 clear ip route [** | <ip address> <subnet mask> ] Use the clear ip route command to remove all learned routes from the IP route table. Stati c and connec ted routes are not cleared by this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 62 clear lld p counters Use the clear lldp counters command to reset all local loop demarkation point (LLD P) pack et c ounters to zero on all interfaces. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 63 clear lld p counters interface <interface> Use the clear lldp counters interface command to reset all local loop demarkation point (LLDP) packet counters to zero for a specified interface.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 64 clear lld p neighbors Use the clear lldp neighbors comman d to remove a ll neighbors from this unit’s database.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 65 clear pppoe <interface id> Use the clear pppoe command to terminate the current PPPoE c lient session and cause the AOS to attempt to re-establish the session.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 66 clear processes cpu max Use the clear processes cpu max c ommand to clear the maximum CPU u sage statistic which is displayed in the show process cpu command output.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 67 clear qos map Use the clear qos map command to clear the statistics for all de fin e d quality of service (QoS) maps or to view detailed information for maps m eeting user -c on figured specifications.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 68 Usage Examples The following example clears st atistics for all defined QoS map s : # clear qos map The foll.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 69 clear route-map counters <map> Use the clear route-map counters command to reset route map hit counters. Synt ax Description <map> S pecifies specific route map to be cleared.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 70 clear sip location [** | <username> ] Use the clear sip location command to clear session initiation protocol (SIP) lo cation database statistics. Synt ax Description ** Clears all dynamic location entries.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 71 clear sip user-registration Use the clear sip user-registration command to clear local session initiation protocol (SIP) server registration information. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 72 clear sp anning-tree counters [interface <interface id> ] The cl ear sp anning-tre e counters command clears the following coun ts: BPDU transmit, BPDU receive, and number of transitions to forwarding state.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 73 clear sp anning-tree detected-protocols [interface <interface id> ] Use the clear spanning-tree detected-protocols command to res tart the protocol migration process.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 74 clear t acacs+ st atistics Use the clear tacacs+ statistics command to delete all terminal a ccess controller access control system (TACACS+) protocol statistics.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 75 clear user [console <user number> | ssh <user number> | telnet <user number> ] Use the clear user command to detach a user from a given line .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 76 clock auto-correct-dst The clock auto-correct-dst command allows the automatic one-hou r correction for Daylight Saving T ime (DST). Use the clock no-auto-corr ect-dst command to disable this feature.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 77 clock no-auto-correct-dst The clock no-auto-correct-dst command allows you to ov erride th e automatic one-hour correction for Daylight Saving T ime (DST). Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 78 clock set <time> <day> <month> <year> Use the clock set command to configure the system software cloc k. For the command to be valid, all fields must be entered.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 79 clock timezone <text> The clock timezon e command sets the unit’ s intern al clock to the timezone of your choice.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 80 Functional Notes The following list shows sample cities and their timezone codes.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 81 Usage Examples The following example set s the timezone for Santiago, Chile.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 82 configure [memory | network | overwrite-network | terminal] Use the configure command to enter the Global Configuratio n mode or to configure the sys tem from memory.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 83 copy <source> <destination> Use the copy command to copy any file from a specified source to a specified destination. Synt ax Description <source> S pecifies the current location of the file to copy .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 84 copy console <filename> Use the copy console command to copy the console’s input to a text file. To end copying to the text file, type < Ctrl+D > .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 85 copy flash <destination> Use the copy flash command to copy a file located in fl ash memory to a specified destina t ion. Synt ax Description <destination> S pecifies th e destination of the copi ed file.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 86 copy <filename> in terface < interface> <slot/port> Use the copy interface command to copy a file to a specified interface. Synt ax Description <filename> S pecifies file name of source file to copy .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 87 copy t f tp <destination> Use the copy tftp command to copy a file located on a networ k Trivial File Transfer Protocol (TFTP ) server to a specified destination.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 88 copy xmodem <destination> Use the copy xmodem command to copy a file (using the XMODE M protoc ol) to a spec ified destination. XMODEM capability is provided in terminal emulation software such as HyperTerminal™.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 89 debug aaa Use the debug aaa command to activate debug messages associ ate d with authentication from the AAA subsystem. Debug messages are displayed (real tim e) on the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 90 debug access-list <listname> Use the debug access-list command to activate debug messa ges (for a specified list) associated w ith access list operation.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 91 debug auto-config Use the debug auto-config command to activate debug messages associated a uto-config events. Debug messages are displayed (real time) on the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 92 debug bridge Use the debug bridge command to display messages associated with bridge events. Debug messages are displayed (real time) to the term inal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 93 debug chat-interfaces <chat interface> Use the debug chat-interfaces command to activate debug messages as soci ated with chat AT comma nd driven interfaces.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 94 debug crypto [ike | ike negotiation | ike client authentication | ike client configuration | ip sec | pki] Use the debug crypto command to activate de bug messages associ ated with IKE and IPSec func tions.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 95 debug dat a-call Use the debug data-call comma nd to activate debug messages associated with data call errors and e vents. Debug messages are displayed (real time) on the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 96 debug demand-routing Use the debug demand-routing command to activate debug messages associated with demand routing errors and events. Debug messages ar e displayed (real time) to the term inal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 97 debug dial-backup Use the debug dial-backup command to activate debug messages associated with dia l-backup operation. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 98 debug dialup-interfaces Use the debug dialup-interfaces command to generate debug messag es used to aid in troubleshooting problems with all dialup interfaces such as the mo dem or the BRI cards.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 99 debug dynamic-dns [verbose] Use the debug dynamic-dns command to display debug messages associated with dynamic domain naming system (DNS). Debug messages are displayed (re al time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 100 debug firewall Use the debug firewall command to activate debug messages associ ated with the AOS fire wall operation. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 101 debug frame-relay [event s | llc2 | lmi] Use the debug frame-relay command to activate debug messages assoc iated with the Frame Relay operation. Debug messages are displayed (real time) to the te rminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 102 debug frame-relay multilink <interface> Use the debug frame-rel ay multilink command to activate debug messages associated with Frame Relay multilink operation.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 103 debug hdlc [errors | verbose] Use the debug hdlc command to activate debug messages associated with the high-level data link control (HDLC) interface. Debug messages are displaye d (real ti me) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 104 debug interface <interface> Use the debug interface command to activate debug messages asso ciated with the specified interface. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 105 debug interface adsl event s Use the debug interface adsl events command to activate debug messages associated with A DSL events. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 106 debug ip bgp [event s | in | out | k eep alives | updates | up dates quiet] Use the debug ip bgp command to activate debug messages associat ed with IP Border Gateway Protocol (BGP).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 107 debug ip dhcp-client Use the debug ip dhcp-client command to activate debug messages associated with Dyna mic Host Configuration Protocol (DHCP) client operation in the AOS.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 108 debug ip dhcp-server Use the debug ip dhcp-server command to activate debug messages associated with Dynamic Host Configuration Protocol (DHCP) serv er op eration in the AOS.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 109 debug ip dns-client Use the debug ip dns-client command to activate debug messages asso ciate d with domain naming system (DNS) client operation in the AOS. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 110 debug ip dns-proxy Use the debug ip dns-proxy command to activate debug messages assoc iated with domain naming system (DNS) proxy operation in the AOS. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 111 debug ip icmp [send | recv] Use the debug ip icmp command to show all Internet Control Message Protocol (ICMP) mess ages as they come into the router or are originated by the router.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 112 debug ip igmp <group-address> Use the debug ip igmp command to enable debug messages for Inte rnet Group Management Protocol (IGMP) transactions (including helper activity).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 113 debug ip mrouting Use the debug ip mrouting command to activate debug messages assoc iated with multicast table routing events. Debug messages are dis played (real time) on the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 114 debug ip osp f Use the debug ip ospf command to activate debug messages assoc iated with open shortest path first (OSPF) routing operati ons. Debug mess ages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 115 Usage Examples The following is an example of debug ip ospf command result s: > enable # debug ip osp f flood OSPF: Update LSA: id=c0a8020d rtid =192.168.2 .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 116 debug ip pim-sp arse Use the debug ip pim-sparse command to display all protocol-ind ependent multicast (PIM) sparse mode information. Debug messages are displaye d (real ti me) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 117 debug ip pim-sp arse assert [event | st ate] <address> Use the debug ip pim-sparse assert c ommand to display debug messages associated with protocol-independent multicast (PIM ) sparse assert transactions.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 118 debug ip pim-sp arse hello Use the debug ip pim-sparse hello command to display protocol-independent multicast (PIM) sparse mode hello transactions. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 119 debug ip pim-sp arse jo inprune [event | st ate] <address> Use the debug ip pim-sparse joinprune command to displa y protocol-independent m ulticas t (PIM) sparse mode join and prune transac tions.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 120 debug ip pim-sp arse packet s [in | out] <interface> <interface id> Use the debug ip pim-sparse packets command to display protoco l-independent multic ast (PIM) spars e mode packet information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 121 debug ip pim-sp arse re gister [event | st ate] <address> Use the debug ip pim-sparse register command to display protocol-indep endent multicast (PIM) sparse source registration messages.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 122 debug ip policy Use the debug ip policy command to display policy-based routin g events. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 123 debug ip rip [event s] Use the debug ip rip command to activate debug messa ges associat ed with Routing Information Protocol (RIP) operation in the AOS. Debug messages are displaye d (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 124 debug ip tcp [event s] Use the debug ip tcp events c ommand to activat e de bug message s associated with significa nt Transmission Control Protocol (TCP) events such as st ate changes, retransmissions, sess ion aborts, etc.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 125 Usage Examples The following is sample ou tput for this comm and: > enable # debug ip tcp event s 2003.02.17 07:40:56 IP .TCP EVENTS TCP: Allocating block 5 2003.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 126 debug ip tcp md5 Use the debug ip tcp md5 command to activate debug messages that de tail the results of each incoming Transmission Control Protocol (TCP) packet’s MD5 au thentication with an internal route in the AOS.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 127 debug ip ud p Use the debug ip udp command to activate debug messages associated with User Da ta gram Protocol (UDP) send and receive events in th e AOS. Debug messages are displayed (real time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 128 Usage Examples The following is sample ou tput for this comm and: > enable # debug ip ud p 2003.02.17 07:38:48 IP .UDP RX: src=10. 200.3.236:1 38, dst=10.200.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 129 debug lld p [rx | tx] verbose Use the debug lldp co mmand to display debu g output for all lo cal loop demarkation point (LLDP) receive and transmit packets. Use the no version of this command to disable it.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 130 debug port-auth [general | p acket [bot h | rx | tx] | auth -sm | bkend-sm | reauth-sm | supp-sm] Use the debug port-auth command to generate debug messa ges used to aid in trouble shooting problems during the port authentication process.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 131 debug ppp [authentication | error s | negotiation | verbose] Use the debug ppp command to activate debug me ssages associated with poin t-to-point protocol (PPP) operation in the AOS.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 132 debug pppoe client Use the debug pppoe client command to activate debug messages associ ated with point-to-point protocol over Ethernet (PPPoE) operation in the AOS.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 133 debug radius Use the debug radius command to enable debug messages fro m the RADIUS subsystem. Debug messages are displayed (real time) to the te rminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 134 debug sip [cldu | location | manager | regist rar <extension> | registration <extension> ] Use the debug sip command to activate debug messages associated w ith Session Initiation Protocol (SIP) events.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 135 debug sntp Use the debug sntp command to enable debug messages assoc i ated with the Simple Network Time Protocol (SNTP). All SNTP packet exchanges and tim e decisions are displayed with these debugging events enabled.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 136 debug sp anning-tree bpdu [r eceive | transmit | all] Use the debug spanning-tree bpdu command to displa y bridge protocol da ta unit (BPDU) debug messages.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 137 debug sp anning-tree [config | event s | general | root] Use the debug spanning-tree command to enable the display of spanning-tree debug messag es. Debug messages are displayed (real time) on the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 138 debug system Use the debug system command to enable debug messages as sociat ed with system events (i.e., login, logouts, etc.). Debug messa ges are displayed (rea l time) to the terminal (or Telnet) screen.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 139 debug t acacs+ p acket s Use the debug tacas+ packets command to activate debug messages associated with termina l access controller access control system (TACACS+) protocol .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 140 debug t ftp [client | server] p acket s Use the debug tftp packets comman d to activate debug me ssages asso ciated with Trivial File Transfer Protocol (TFTP) packets.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 141 dir Use the dir command to display a directory list of files on the system. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 142 dir [ <input> | flash | flash <input> ] Use the dir flash command to list all of th e files stored in flas h. Synt ax Description <input> Lists all file s stored in flash t hat match the specified pa tter n.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 143 disable Use the disable command to exit the Enable mo de and enter the Basic mode. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 144 enable Use the enable command to enter a passwo rd for the Enable mode. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 145 erase [ <filename> | st artup-config] Use the erase command to erase the specified file. Synt ax Description <filename> S pecifies the name of the file (located in FLASH memory) to erase.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 146 event s Use the events command to enable event reporting to the current command line interface (CLI) session. Use the no form of this command to disable all ev ent reporting to the current CLI session.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 147 exception report generate Use the exception report generate command to immediately gene rate an exception report. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 148 logout Use the logout command to terminate the current sess i on a nd return to the login scree n. Synt ax Description No subcommands. Default V alues No default s necessary for this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 149 ping <address> Use the ping command (at the Enable mode prompt ) to verify IP network connectivity. Synt ax Description <address> Optional. S pecifies the IP address of the system to ping.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 150 The following is a list of availab le extend ed ping fields with descriptions: T arget IP address: S pecifies the IP address of the system to ping. Repeat Count: S pecifies the number of ping pack ets to send to the syste m (valid range: 1 to 1,000,000).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 151 reload [cancel | in <delay> ] Use the reload command to preform a ma nual reload of the AOS. Synt ax Description cancel Optional. Deactivates a pending reload command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 152 show access-list s <listname> Use the show access-lists command to display all c onfigured access lis ts in the system (o r a specific list). Synt ax Description <listname> Optional.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 153 show arp [realtime] Use the show arp command to display the Address Re solution Protocol (ARP) table. Synt ax Description realtime Displays full-screen output in real time.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 154 show auto-config Use the show auto-config command to display auto-con figu ration status. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 155 show bridge <interface> <slot/port> <bridge group #> Use the show bridge command to displa y a list of all configured bridge groups (inc luding individual members of each group).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 156 show buffers [realtime] Use the show buffers command to display the st atistics for the buffer pools on the network server. Synt ax Description realtime Displays full-screen output in real time.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 157 show buffers users [realtime] Use the show buffers users command to display a list of the top us ers of packet buffers. Typically, this command will only be used as a de bug tool by ADTRAN personnel.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 158 6 0x001d8298 2 7 0x0010d970 1 8 0x00000000 0 9 0x00000000 0 10 0x00000000 0 1 1 0x00000000 0 12 0x00000000 .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 159 show clock [det ail] Use the show c lock command to display th e system time and date entered using the clock set command. Refer to the section clock set <time> <day> <month> <year> on page 7 8 for more information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 160 show configuration Use the show config uration command to display a text printout of th e startup configuratio n file stored in nonvolatile random access memory (NVRAM).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 161 ! ! interface eth 0/1 speed auto no ip address shutdown ! interface dds 1/1 shutdown ! interface bri 1/2 shutdown ! ! ip access-list standard Outbound permit host 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 162 show connections Use the show connections command to display information (includin g TDM group assignments) for all active connections. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 163 show crypto ca [certific ates | crls | profiles] Use the show crypto ca command to display info rmation regarding certificates and profiles. Synt ax Description certificates Displays information on all certificates.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 164 show crypto ike Use the show crypto ike command to display information regarding the IKE configuration.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 165 Usage Examples The following is a sample from the show crypto ike policy co mmand: > enable # show crypto ike po licy Crypto IKE Policy 100 Main mode Using System Local ID Address Peers: 63.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 166 show crypto ip sec Use the show crypto ipsec command to display information re garding the IPSec configuration.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 167 show crypto map Use the show crypto map command to display information regardin g crypto map settings .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 168 show debugging Use the show debugging command to display a list of all activa ted debug message categories. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 169 show demand Use the show demand command to display information regarding demand routing parameters and statistics.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 170 Keep-alive is set (10 sec.) Admin MTU = 1500 Mode: Either , 1 dial entries, idleT ime = 120, fastIdle = 20 Resource pool demand No authentication configured IP address 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 171 The following is example output from the s how demand resource pool command: > enable # show demand reso.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 172 show dial-backup interfaces Use the show dial-backup interfaces command to display all configured dia l -bac kup interfaces and the associated parameters for each.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 173 Backup phone number list: Number Call T ype min/max DS0s Backup I/F 5551212 analog 1/ 1 ppp 2.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 174 show dynamic-dns Use the show dynamic-dns command to show informa tion related to the dynami c domain naming system (DNS) configuration. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 175 show event-history Use the show event-history command to display all en tries in the current local event-history log. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 176 show fan-t ach Use the show fan-tach command to view the unit’ s current fan speed. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 177 show flash Use the show flash command to display a list of all fil es currently stored in FLASH memory. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 178 show frame-relay fr agment [frame-relay <port.sublink> ] Use the show frame-re lay fragment command to display FRF.12 sta tistics for Frame Relay sublinks enabling FRF.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 179 show frame-relay Use the show frame-relay command to display configuration an d status parameters fo r configured virtual Frame Relay interfaces.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 180 Usage Examples The following are sample output s from various show frame-relay commands: >enable # show frame-relay lmi LMI statistics for interface FR 1 LMI TYPE = ANSI Num S tatus Enq.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 181 show frame-relay multilink <interface> det ailed Use the show frame-relay multilink command to display information a ssociated with the Frame Relay multilink interface.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 182 show hosts [verbose] Use the show hosts command to display in formation such as the domain name, name lookup service, a list of name server hosts, and the cached list of host names and address es on the network to which yo u can connect.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 183 show interfaces <interface> Use the show interf aces command to display configuration para meters and current statistics for all interfaces (or a specified interface).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 184 Command History Release 1.1 Command was introdu ced. Release 6.1 Command was upda te d to include performance-statistics option. Release 9.1 Command was exp anded to include HDLC and tunnel interfaces.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 185 # show interfaces mod em 1/2 modem 1/2 is UP Line status: on-hook Caller ID will be us ed to route incoming.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 186 # show interfaces f r 1 TDM group 10 line protocol is UP Encapsulation FRAME-RELA Y (fr 1) 463 packet s inp.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 187 show ip access-list s <listname> Use the show ip ac cess-lists command to display all configured IP access lists in the system. Synt ax Description <listname> Optional .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 188 show ip arp [realtime] Use the show ip ar p command to display the Address R esolution Protocol (ARP) table. Synt ax Description realtime Displays full-screen output in realtime.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 189 show ip as-p ath-list [ <listname> ] Use the show ip as-path-list command to display any AS pa th lists that have been configured in the router, along with any permit and de ny clauses in each list.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 190 show ip bgp community [ <community number> . . . <community number> | internet | no export| loc.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 191 Usage Examples In the following example, all BGP routes are disp layed whose co mmunity numbers match those listed in the show ip bgp community com mand. > enable # show ip bgp community local-as 10:405 BGP local router ID is 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 192 show ip bgp community-list <community-list-name> [exact] Use the show ip bgp community-list command to display Border Gatewa y Protocol (BGP) routes that are permitted by the specified community list.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 193 Usage Examples In the following example, all BGP routes are displa yed whose commu nity numbers ma tch those define d in the community lis t named CList1. > enable #show ip bgp community-list CList 1 BGP local router ID is 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 194 show ip bgp [regexp <expression> | summary] Use the show ip bgp command to displa y a summary of the Bord er Gateway Protocol (BG P) route table. Synt ax Description <expression> S pecifies the regular ex pre ssion to filter on.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 195 * 10.22.130.240/28 1 0. 22.132.9 303 300 i *> 10.22.131.0/29 10 .22.131.1 30 2 i *> 10.22.131.0/29 10.22.131.9 302 i 10.22.131.0/29 10.22. 132.9 303 304 302 i *> 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 196 10.22.134.32/29 10.22. 131.9 303 304 i *> i10.22.134.40/29 1 0.22.134.10 100 i 10.22.134.40/29 10. 22.131.9 3 02 304 i 10.22.134.40/29 10. 22.132.9 303 304 i *> i10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 197 10.22.134.26 4 304 172 174 0 0 0 2:41:43 10 10.22.134.34 4 3 04 164 174 0 0 02:41:40 4 The following sample output of the show ip bgp regexp _303_ command sho w s all of the entries in the BGP database th at contain "303" in the AS p ath.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 198 show ip bgp <network ip> [ </length > | <network-mask> ] Use the show ip bgp <network .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 199 show ip bgp neighbors <ip address> Use the show ip bgp neighbors command to display information fo r the specified Border Gatewa y Protocol (BGP) neighbor.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 200 Usage Examples The following are output vari ation s of the show ip bgp neighbors com mand: > enable # show ip bgp neighbors BGP neighbor is 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 201 # show ip bgp neighbors 10.15.43.17 received-routes BGP local router ID is 10.0.0.1, local AS is 101. S tatus codes: * valid, > best, i - internal Origin codes: i - IGP , e - EGP , ? - incomplete Network NextHop Metric Path *> 1.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 202 show ip community-list [ <community-list-name> ] Use the show ip community-list co mma nd to display any or all defi ned community lists in the router configuration.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 203 show ip dhcp-client lease <interface> Use the show ip dhcp-client lease command to display all Dynamic Host Client Protocol (DHCP) lease information for interfaces that have dynamically assigned IP addresses.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 204 show ip dhcp-server binding <client ip address> Use the show ip dhcp-server binding command to display the Dynamic Ho st Client Protocol (DHCP) server client table with associated information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 205 show ip igmp group s <group-address> Use the show ip igmp groups command to display the multicast groups that have been registered by directly connected receive rs us ing Internet Group Management Protocol (IGMP).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 206 show ip igmp interface <interface> Use the show ip igmp interface command to display multicast-relate d information per-interface. If no interface is specified, this command shows information for all interfaces.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 207 show ip interfaces [ <interface> | brief] Use the show ip interfaces command to display the status informat ion for all IP interfaces (or a specific interface).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 208 show ip local policy Use the show ip local policy command to display information ab out the route-map used for local policy-based routin g. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 209 show ip mroute [ <group-address> | <interface> ] [summary | all] Use the show ip mr oute command to display IP multicas ting routing table information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 210 The following is sample output from the show ip mroute all command: > enable #show ip mroute al l IP Mul.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 211 show ip osp f Use the show ip os pf command to display general information regarding open shortest path first (OSPF) processes. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 212 show ip osp f data base Use the show ip ospf database command to display information from th e open shortest path first (OSPF) database regarding a specific router.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 213 Functional Notes The link state ID dif fers depe nding on whether the link state ad vertisement in question describes a network or a router . If describing a network, this ID is one of the following: • The network’s IP addr ess.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 214 show ip osp f interface <interface> Use the show ip os pf interface command to display open shortest pa th first (OSPF) information for a specific interface.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 215 show ip osp f neighbor <interface> <neighbor id> [detail] Use the show ip ospf neighbor command to di splay open shortest path first (OSPF) neighb or information for a specific interface.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 216 show ip osp f summary-address Use the show ip os pf summary-address command to display a list of all summary address redistribution information for the system.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 217 show ip pim-sp arse [interfaces <interface> | neighbor | rp-map | rp-set | st ate | traffic] Use the show ip pim-sparse command to display Protocol Independ ent Multicast (PIM) configuration information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 218 The following example shows sample output from the show ip pim-sp arse interfaces command: >enable # show ip pim- sp arse interfac e eth 0/1 is UP PIM S parse DR: itself Local Address: 192.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 219 The following example shows sample output from the show ip pim-sp arse rp-map command: >enable # show ip pim-sp arse rp-map Number of group-to-RP mappings: 5 Group address RP address ---------- ----------- --------- ---------- ----------- ------ 225.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 220 eth 0/1, Forward, 02:42:03 /00:03:03 Downstream Join/Prune S tate: Join Assert Winner S tate: No Info Assert Timer (sec): sto pped Assert Winner: 0.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 221 show ip policy Use the show ip policy command to display whi c h route-map is associated with which interface for policy-based routin g. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 222 show ip policy-class <policyname> Use the show ip policy-class command to display a list of currently configured access policies.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 223 show ip policy-sessions <policyname> [all] Use the show ip policy-sessions command to display a list of current policy class associa tions.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 224 Usage Examples The following is sample output from the sh ow ip polic y-sessions command: > enable # sho.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 225 show ip policy-st at s <policyname> Use the show ip policy-stats command to display a list of current policy class statistics.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 226 show ip prefix-li st [det ail | summary] <listname> Use the show ip prefix-list command to display BGP pr efix list information. Synt ax Description det ail Shows a listing of the prefix list rules and their hit counts.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 227 show ip protocols Use the show ip pro tocols command to display IP routing protocol parameters and statistics. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 228 show ip route [connected | osp f | ri p | st atic | t a ble | bgp | summary | summary realtime | <ip address> <subnet> ] Use the show ip route command to display the conten ts of the IP route table.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 229 Usage Examples The following is a sample output from the sh ow ip route command: > enable # show ip rout.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 230 show ip traffic [realtime] Use the show ip traffic command to display all IP traffic statistics. Synt ax Description realtime Displays full-screen output in real time.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 231 show lld p Use the show lldp command to display local lo op demarkation po int (LLD P) timer configuration. Synt ax Description No subcommands. Default V alues No default values are nece ssary for this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 232 show lld p device <system name> Use the show lldp de vice command to display specif ic neighbor information about a given neighbor. Synt ax Description <system name> Specifies the syste m name of the neighb or to displa y .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 233 show lld p interface <interface> Use the show lldp inte rface command to display local loop demark ation point (LLDP) configuration and statistics for interfaces on this device.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 234 show lld p neighbors [interface <interface> l <interface type> | det ail | realtime] Use the show lldp neighbors inte rface command to display informati on about neighbors of this device learned about via local loop demarkation point (LLDP).
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 235 Usage Examples The following example shows det ailed information about a device’ s neighbors: > enable.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 236 show lld p neighbors statistics Use the show lldp neighbors statistics command to display st atistics about local lo op demark ation point (LLDP) neighbor table actions.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 237 show memory [heap | r ealtime | uncached-heap] Use the show memory command to display statisti cs regarding memory includ ing memory allocation and buffer use statistics.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 238 Usage Examples The following is a sample output from the show memor y heap command: >enable # show memor.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 239 show modules [verbose] The show modules command displays information on the current system setup. Synt ax Description verbose Enables detailed messaging. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 240 show output-st artup Use the show output-startup command to dis play startup configura tion output line-by-line. This output can be copied into a text file and th en used as a configuration editing tool.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 241 show power supply The show power supply command d isplays the power supply status. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 242 show pppoe Use the show pppoe command to display all point-to-point over Ethernet (PPPoE) settings and associated parameters. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 243 show processes [cpu | cpu realti me | history | queue | st ack] Use the show proce sses command to display process statistic information. Synt ax Description cpu Displays informations about processes that a r e currently active.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 244 T a sk T ask Invoked Exec T ime Runtime Loa d % D Name PRI ST A T (count ) (usec) (usec) (1sec) 0 Idle 0 W 129689 1971 927923 9 2.79 1 FrontPanel 249 W 9658 165 3202 0.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 245 show qos map The show qo s map command outputs informa tion about the quality of service (QoS) map. This information dif fers based on how a particular map entry is defined.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 246 Usage Example > enable # show qos map qos map priority map entry 10 match IP packets with a preced ence .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 247 The following example shows the “priority” Qos Map and all entries in that map: > enable # show qos .
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 248 The following examples show Qos Map interface stat s associated with the map defined for an interface: >.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 249 show queue <interface> Use the show queue command to display co nversa tion information associated with an interface queue. This command shows summary an d per-conversation information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 250 show queuing [fair] Use the show queuing command to display information associat ed with configured queuing methods. Synt ax Description fair Optional. Displays only information on the weighted fair queuing configuration.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 251 show radius st atistics Use the show radius statistics command to display various statisti cs from the RADIUS subsystem.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 252 show route-map [ <name> ] Use the show route-map command to display an y route-maps that have been configured in t h e router.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 253 Match clauses: ip address (access-lists): Acl1 Set clauses: metric 100 BGP Filtering matches: 10 routes Pol.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 254 Set clauses: metric 200 BGP Filtering matches: 12 routes Policy routing matches: 0 packets 0 bytes In the example below , only RouteMap3 is displayed.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 255 show running-config Use the show running-config command to display a text print of all the non-default parameters contained in the current running configuration file.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 256 Applicable Plat forms This command applies to the NetV ant a 300, 1000, 1000R, 2000, 3000 , 4000, and 5000 and T otal Access 900 Series units. Command History Release 1.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 257 show sip [resources | statistics | tr unk-registration | user-registration] Use the show s ip command to display Session Initiation Prot ocol (SIP) statistical and registration information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 258 show sip location [dynamic | st atic] Use the show sip location command to display Session Initiation Protocol (SIP) statistical and registration information.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 259 show snmp Use the show snmp command to display the system S imple Network Management Protocol (SNMP) parameters and current status of SNMP communications. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 260 show sntp Use the show sntp command to display the system Simple Network Time Pro tocol (SNTP) parameters and current status of SNTP communications. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 261 show sp anning-tree <bridgegroup#> Use the show spanning-tree command to display the status of the spanning-tree protocol. Synt ax Description <bridgegrou p#> Optional.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 262 show startup-config Use the show startup-config command to display a text printout of t he startup configuration file stored in NVRAM. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 263 ! ! interface eth 0/1 speed auto no ip address shutdown ! interface dds 1/1 shutdown ! interface bri 1/2 shutdown ! ! ip access-list standard MatchAll permit host 10.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 264 show st artup-config checksum Use the show st artup-config checksum command to display the Message Digest 5 (MD5) checks um of the unit’s startup configuration.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 265 show system The show system command shows the system version, timin g source, power source, and alarm relay status. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 266 show t acacs+ st atistics Use the show tacacs+ statistics command to display terminal access controller access control system (TACACS+) client statistics. Synt ax Description No subcommands.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 267 show tcp info [realtime] <control block> Use the show tcp info command to display Transmission Control Protocol (TCP) contr ol block information in the AOS.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 268 ID 0 1 2 3 4 5 ST A TE FREE LISTEN LISTEN LISTEN LISTEN FREE LST A TE FREE FREE FREE FREE FREE FREE OST A T.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 269 show temperature Use the show temper ature command to display the unit temperature. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 270 show threshol ds Use the show thresholds command to display thr esholds currently crossed for all DS1 interfaces. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 271 show users [realtime] Use the show users command to display the name (if any) and state of users authenticate d by the system.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 272 Usage Examples The following is a sample of show users output: > enable # show users - CONSOLE 0 'adtran' logged in and enable d Idle for 00:0 0: 00 - TELNET 0 ( 172.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 273 show version Use the show version command to display the current ADTRAN operating system (AOS) version information. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 274 sip check-sync Use the sip check-sync command to send a check-sync notification to all IP phones registered to the unit. When an IP phone receives this chec k-sync notification, the phone will check for possib le configuration changes stored on the server.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 275 telnet <address> Use the telnet command to open a Telnet session (through th e AOS) to another s ystem on the network. Synt ax Description <address> S pec ifies the IP address of the remote system.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 276 terminal length <text> The terminal length command sets the number of rows (lin es) for a terminal session. Use the no form of this command to return to the default value.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 277 traceroute <address> source <address> Use the traceroute command to display the IP routes a pac ket takes to reach the specified destination. Synt ax Description <address> Optional.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 278 undebug all Use the undebug all command to disable all activated debug messages. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 279 wall <message> Use the wall command to send messages to all users curren tly logged in to the AOS unit. Synt ax Description No subcommands. Default V alues No default s necessary for this command.
Command Refere nce Guide Enable Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 280 write [dynvoice-config | erase | memory | network | terminal] Use the write command to save the ru nning configuration to the unit’s nonvolatile random access memory (NVRAM) or a Trivial File Transfer Protocol (TFTP) server.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 281 G LOBAL C ONFIGURATION M ODE C OMMAND S ET To activate the Global Configuration mode, enter the configuration command at the Enable Security mode prompt.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 282 data-call [authenticatio n protocol | sent authentic ation protocol] [chap | pap] on page 333.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 283 line [console | telnet | ssh] <line-number> <e nding number> on page 413 lldp [mi.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 284 aaa accounting commands <level> [ <listname> | default] [none | stop-only] [group <groupname> | group tacacs+] Use aaa accounting commands to set parameters for AAA accou nting.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 285 aaa accounting [supp ress null-username] Use the aaa accounting suppress null-username comman d to stop sending accou ntin g records for usernames set to null.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 286 aaa accounting up date [newinfo | periodic <minutes> ] Use the aaa accounting update command to specify when accounting re cords are sent to the server.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 287 aaa authentication [banner | fai l-message | p assword-prompt | username-prompt] Use the aaa authentication command to co ntrol various features of th e AAA subsys tem authentication process.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 288 Enter TEXT message. End with the character '#'.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 289 aaa authentication enable d efault [none | line | enable | group <groupname> | group ra.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 290 aaa authentication login [ <listname> | default] [none | line | enable | local | group .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 291 Usage Examples The following exam ple creates a nam ed list called myList and specifies using.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 292 aaa authorization commands <level> [ <listname> | defau lt] [group <groupname> | group t acacs+ | if-authenticated | none] Use aaa authorization commands to create (or change) a list of method s for user authoriz ation.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 293 aaa authorization [config- command | console] Use the aaa authorization to enable or disable authorization fo r configuratio n mode commands and for console mode.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 294 aaa group server [r adius | t acacs+] <listname> Use the aaa group server comman d to group pre-define d RADIU S and TACACS+ servers into named lists.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 295 Usage Examples The following example crea tes the named list myServer s and enters the RADIUS.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 296 aaa on Use the aaa on command to activate the AAA subsystem. Use the no form of this command to deactivate AAA. Synt ax Description No subcommands.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 297 The AAA system allows users to create a named list of these methods to at tempt in order (if one fails, it falls to the next one on the list). This named list is then attached to a por tal (telnet 0-4 or console 0-1).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 298 aaa processes <threads> Use the aaa processes command to set the number of threads available to the AAA subsystem. Use the no form of this command to return to the default setting.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 299 arp <ip address> <mac address> arp a Use this command to enter static entries into the address resolution protocol (ARP) table. Synt ax Description arp a Sets the st andard address resolution protocol for this interfa ce .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 300 auto-config [filename <name> | restart | retry-count <number> | s erver <name or address> ] Use the auto-config command to enable the automatic self-con figuration feature in ADTRAN OS.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 301 The following command specifies the na me of the file to download: (config)# auto-config file.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 302 banner [exec | login | mot d] <character> <message> <character> Use the banner command to specify messag es to be displayed in certain situations.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 303 boot system flash <filename> [no-backup | <backup filename> ] Use the boot system flash command to specify the system image loaded at startup.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 304 bridge <group#> protocol ieee The bridge protocol ieee command configur es a bridge group fo r the IEEE Spanning-Tree Protocol. Use the no form of this command (with the approp riate arguments) to delete this setting.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 305 clock [auto-correct-dst | no-auto-correct-dst] The clock auto-correct-dst command allows the unit to automatically correct for Daylight Saving T ime (DST).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 306 clock set <time> <day> <month> <year> Use the clock set command to configure the system software cloc k. For the command to be valid, all fields must be entered.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 307 clock timezone <text> The clock timezon e command sets the unit’ s intern al clock to the timezone of your choice.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 308 Functional Notes The following list shows sample cities and their timezone codes.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 309 Usage Examples The following example set s the timezone for Santiago, Chile.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 310 cross-conne ct <#> <from interface> <slot/port> <tdm-group#> <to i.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 311 Usage Examples The following example creates a Frame Relay endpoint and connects it to th e T1 1/1 physical interface: 1.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 312 S tep 2: Create the sub-interface and configure the PVC parameters.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 313 crypto ca authenticate <name> Use the crypto ca authenticate command to initiate CA authentication procedures. Synt ax Description <name> S pecifies a CA profile using an alphanu mer ic string up to 32 characters.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 314 Zc2sXYyrBPtv6k2ZGGY qXAUZ98/txm37JwQGafygePJ/64oeisV eDcLf2FTjveex W5saydjSK00jXjreRZcJFEDmfR.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 315 crypto ca certificate chain <name> Use the crypto ca certificate chain comma nd to enter the Ce rtific ate Co nfiguration for the specified CA.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 316 crypto ca enroll <name> Use the crypto ca enroll command to begin CA enrollment procedures. Synt ax Description <name> S pecifies a CA profile using an alphanumer ic string (up to 32 characters).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 317 Usage Examples The following example shows a typical enrollmen t dialog: (config)# crypto ca enroll MyProfile **** Press CTRL+C to exit en ro llment request dialog.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 318 crypto ca import <name> certificate Use the crypto ca import certificate command to import a certificate ma nually via the console terminal .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 319 VGVjaFN1cHBvcnQxET APBgN VBAMTCHRzcm91 dGV yg hAZq l7OwISgsUhfaSeGh0Ot MGkGA1UdHwRiMGAwLaAroC.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 320 crypto ca import <name> crl Use the crypto ca import crl command to import a CRL manua lly via the console terminal. Synt ax Description <name> S pecifies a CA profile using an alphanumer ic string (up to 32 characters).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 321 crypto ca profile <name> Use the crypto ca profile command to define a CA and to enter th e CA Profile Configuration. Refer to CA Profile Configuration Command Set on pag e 1028 for more information.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 322 crypto ike Use the crypto ike command to define the system -level local ID for IKE nego tiations and to enter the IKE Client or IKE Policy command sets.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 323 T echnology Review The following example configu re s an AOS product for VPN using IKE aggr essive mode with pre-shared keys. The AOS product can be set to initia te IKE negotiation in main mode or aggressive mode.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 324 An IKE policy may specify one or more peer IP addresses that will be allowed to connect to this system. T o specify multiple unique peer IP addresses, the peer A.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 325 St e p 8 : Create crypto map. A cryp to m ap is used to d efine a set of encryptio n schemes to be used for a given interface. A crypto map entry has a unique index within the cryp to map set.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 326 crypto ike remote-id Use the crypto ike remote-id command to specify the remote ID and to associate a pre-shared key with the remote ID. Synt ax Description address <IPv4 address> S pecifies a remot e ID of IPv4 type.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 327 Functional Notes The fqdn and user-fqdn <fqdn> line can include wildcard characte rs. The wildcard charac ters are “ * ” for a 0 or more character match and “?” fo r a single characte r match.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 328 Example for typical asn1-dn format with wildcards used to match a string within a field: cryp.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 329 crypto ip sec transform-set <setname> <parameters> Use the crypto ipsec transform-set command to define the transform configuration fo r securing data (e.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 330 Usage Examples The following example first create s a transform set ( Set1 ) consisting of tw.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 331 crypto map Use the crypto map command to define crypto map names and nu mbers and to enter th e associated mode (either Crypto Map IKE or Crypto Map Manual).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 332 If no transform set or access list is configured for a crypto map, the entry is inco mplete and will have no effect on the system.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 333 dat a-call [authentication protocol | sent authentication protocol] [chap | p ap] Use the dat.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 334 dat a-call [mtu <number> | multilink] Use the data-call commands to set the pre-authentication defa ults for maximum transmit unit (MTU) size or to enable multilink for inbound demand ro uting calls.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 335 enable p assword [md5] <password> Use the enable password command to define a password (with optional encryption) for accessing the Enable mode.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 336 Usage Examples T o provide extra securi ty , th e AOS can encrypt the Enable p a ssword when displaying the curr ent configuration.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 337 event-history on Use the event-history on command to enable event logging for the AOS system. Event log messages will not be recorded unless this command has been issued (regardless of the event-history priority configured).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 338 event-history priority [error | fat al | info | notice | warning] Use the event-history priority command to set the threshold for even ts stored in the event history.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 339 Usage Examples The following e xample logs a ll events to the even t history: (config)# event.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 340 exception report [filename <filename> ] Use the exception report command to specify the output f ilename for the exception report. Synt ax Description filename <filename> Optional.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 341 f tp authentication <listname> Use the ftp authentication command to attach AAA login a.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 342 hostname <name> Creates a name used to identify the unit. This alphanumeric string should be us ed as a unique description for the unit. This string wi ll be displayed in all prompts.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 343 interface <interface> [ <slot/port> | <interface id> ] [point-to-point] Use the interface command to activate the interface command set for the specified physical or virtual interface.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 344 ip access-list extended <listname> Use the ip access-list extended command to create an empty access list and enter the extended access -list.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 345 The following keywords and por t numbers are supported for the <source port> field: any Matches any destination port. eq <port number> Matches only packets on a given port number .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 346 The following is the list of TCP port numb ers that may be identified using the text name (in.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 347 <icmp-code> Optional. Filters ICMP packe ts that are filtered using the ICMP message type (using the <icmp-type> keyword) may also be filt ered using the ICMP message code (valid range: 0 to 255).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 348 Usage Examples The following example crea tes an access list AllowIKE to allow all IKE (UDP Port 500) p a ckets from the 190.72.22.55.0 /24 network: (config)# ip access-list extended AllowIKE (config-ext-nacl)# permit ud p 190.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 349 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 350 ip access-list st andard <listname> [permit | deny] <ip address> Use the ip access-list standar d command to create an empty access list and enter the standard access-list.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 351 Functional Notes Access control lists are used as packet selectors by access policies (ACPs); by themselves they do nothing. ACLs are composed of an or der ed list of entries with an implicit deny all at the end of ea ch list.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 352 Usage Examples The following example crea tes an access list UnT rusted to deny all pa ckets from the 190.72.22.248/30 network: (config)# ip access-list sta ndard UnT rusted (config-std-n acl)# deny 190.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 353 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 354 ip classless Use the ip classless command to forward class less packets to the best supernet route available. A classle ss packet is a pac ket addressed for delivery to a subn et of a network with no default network route.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 355 ip crypto Use the ip crypto command to enable AOS VPN functionality and a llow crypto maps to be added to interfaces. Use the no form of this command to disable the VPN functionality.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 356 ip default-gateway <ip address> Use the ip default-gateway command to specify a default gateway if (and only if) IP routing is NOT enabled on the unit.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 357 ip dhcp-server dat abase local Use the ip dhcp-server database local command to configure a DHCP data base agent with local bindings. Use the no form of this command to disable this option.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 358 ip dhcp-server excluded-address <st art ip> <end ip> Use the ip dhcp-server excluded-address command to specify IP addresses that cannot be assigne d to DHCP clients.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 359 ip dhcp-server ping p ackets <#packets> Use the ip dhcp-server ping packets command to specify the number of ping packets the DHCP server will transmit before assigning an IP address to a requesting DHCP client.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 360 ip dhcp-server ping timeout <milliseconds> Use the ip dhcp-server ping timeout command to specify th e interval (in milliseconds) the DHCP server will wait for a response to a transmitted DHCP ping packet.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 361 ip dhcp-server pool <name> Use the ip dhcp-server pool command to create a DHCP addres s po ol and enter the DHCP pool. Use the no form of this command to remove a config ured DHCP address pool.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 362 ip domain-lookup Use the ip domain-lookup command to enable the IP domain naming s ystem (DNS), allo wing DNS-based host translation (name-to-address).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 363 ip domain-name <name> Use the ip domain-name command to define a default IP domain name t o be used by the AOS to resol ve host names. Use the no form of this command to disable this function.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 364 ip domain-proxy Use the ip domain-proxy command to enable DNS proxy for the router . This enables the router to act as a proxy for other un its on the network.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 365 ip firewall Use the ip firewall command to enable AOS se curity features including access control policies and lists, Network Address Translation (NAT), and th e stateful inspection firewall.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 366 Functional Notes This command enables firew all processing for all in terfaces with a configured policy class.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 367 T echnology Review Concept s: Access control using the AOS firewall has two fundamen tal p art s: Acce ss Control Lists (ACLs) and Access Policy Classes (ACPs).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 368 Case 4: Packet s from interfaces without a configured policy class to other interfac es without a configured policy class This traffic is routed normally .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 369 Attacks that send TCP URG packets Y es Any TCP packets that have the URG flag set are discarded by the firewall.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 370 Application Spe cific Processing: The following applications and pro tocols require sp ecial processing to op er ate concurrently with NA T/firewall functionality .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 371 ip firewall alg [f tp | h323 | pptp] Use the ip firewall alg command to enable the application-le vel gateway (ALG) for a particular application.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 372 ip firewall alg sip ud p <port#> Use the ip firewall alg sip udp command to configure the user datagr am protocol (UDP) port for Session Initiation Protocol (SIP) application-level gateways (ALG).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 373 ip firewall att ac k-log threshold <value> Use the ip firewall attack-log threshold command to specify the number of attack mounting attempts the AOS will identify before generating a log message.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 374 ip firewall check reflexive-traffic Use the ip firewall check reflexive-traffic command to enable the AOS stateful inspection firewall to process traffic from a primar y subnet to a secondary s ubnet on the same interface through the firewall.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 375 ip firewall ch eck syn-flood Use the ip firewall check syn-flood command to enable the AOS stateful inspection fi rewall to filter out phony TCP service requests and allow only le gitimate requests to pass through.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 376 ip firewall check winnuke Use the ip firewall check win nuke command to enable the AOS stateful inspection firewall to discard all out of band (OOB) data (to protect against WinNuke attacks).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 377 ip firewall policy-log threshold <value> Use the ip firewall policy-log threshold command to specify the number of connections required by an access control policy before the AOS will generate a log message.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 378 ip forward-protocol ud p <port number> Use the ip forward-protocol udp command to specify the protocols and ports the AOS allows when forwarding broadca st pac kets.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 379 Applicable Plat forms This command applies to the NetV ant a 300, 1000R, 2000, 3000, 4000, and 5000 and T otal Access 900 Series units. Command History Release 2.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 380 ip f tp access-class <policyname> in Use the ip ftp access-class in command to ass ign an access policy to al l self-bound File Transfer Protocol (FTP) sessions.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 381 ip f tp agent Use the ip ftp agent command to enable the file transfer protocol (FTP) agent. Synt ax Description No subcommands. Default V alues By default, the FTP agent is enabled.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 382 ip f tp source-interface <interface> Use the ip ftp source-inter face command to use the spec ifie d interf ace’ s IP address as the source IP address for FTP traffic transm itted by the unit.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 383 ip host <name> <address1> Use the ip host co mmand to define an IP host nam e. This a llows you to statically map host names and addresses in the host cache.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 384 ip igmp join <group-address> Use the ip igmp join command to instruct the router stack to join a specific group. The stack may join multiple groups.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 385 ip load-sharing [per-des tination | per-p acket] Use the ip load-sharing command to configure wheth er parallel rou tes in the rou te table are used to load-share forwarded packet s.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 386 ip local policy route-map <map-name> Use this command to specify a route- map for local policy routing on the device. This setting is applied to the local network interface.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 387 ip mcast-stub helper-address <ip address> Use the ip mcast-stub helper-address command to specify an IP address toward which IGMP host reports and leave messages are forwarded.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 388 ip multicast-routing Use the ip multicast-routing command to enable the multicast rout er process. The command does not affect other multicast-related configurations.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 389 ip name-server <server- address1-6> Use the ip name-server command to designate one or more name servers to use for name-to-address resolution.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 390 ip policy-class <policyname> max-sessions <number> Use the ip policy-class command to create an access control polic y and enter the access control policy.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 391 Functional Notes AOS access control policies are used to allow , discar d, or manipulate (using NA T ) d a ta for each physical interface. Each ACP consists of a selector ( access list ) and an action ( allow , disca rd , NA T ).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 392 T echnology Review Creating access policies and list s to regulate traf fi c through the routed network is a four-step pr ocess: St e p 1 : Enable the secur ity fe at ur es of the AOS using the ip firewall command.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 393 nat source list <access li st names> interface <interface > overload policy <a.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 394 ip policy-timeout <protocol> <range> <port> <seconds> Use multiple ip.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 395 Default V alues <seconds> The following default policy timeout intervals apply: tcp (60.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 396 Usage Examples The following examp le creates customized p o licy timeouts for the following:.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 397 ip prefix-list <listname> description <“text”> Use the ip prefix-list description command to create an d name prefix lists. Synt ax Description <listname> S pecifies a particular prefix list.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 398 ip prefix-list <listname> seq <sequence#> [permit | deny] <network/len> [le <le-value> | ge <ge-value> ] Use the ip prefix-list seq command to spec ify a prefix to be ma tched or a range o f m ask lengths.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 399 Usage Examples The following example creates a pr efix list e ntry in the pr efix list t est matching only the 10.0.0.0/8 network: (config)# ip prefix-l ist test seq 5 deny 10.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 400 ip radius source-interface <interface> Use the ip radius source-interface command to specify the network-attached storage (NAS) IP address attribute passed with the RADIUS authentication request packet.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 401 ip route <ip address> <subnet mask> <i nterface or ip address> <administrative distance> Use the ip route command to add a static route to the route table.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 402 ip routing Use the ip routing command to enable the AOS IP routing functionality. Use the no form of this command to disable IP routing. Synt ax Description No subcommands.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 403 ip rtp firewall-traversal [policy-timeout <seconds> ] Use the ip rtp fire wall-traversa.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 404 ip scp server Use the ip scp server to enable the secure copy (SCP) server. SCP is a more secure form of the older Berkley r-tool RCP or remote copy.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 405 ip sip [dat abase local | location] <username> <ip address> Use the ip sip database local command to store the databa se of SI P usernames across a reboot.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 406 ip sip proxy Use the ip sip proxy command to enable or dis able the proxy server. No subcommands. Default V alues By default, this command is enabled.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 407 ip sip registrar [ authenticate | default-expires | max-expires | min-expires | realm] <timevalue> Use the ip sip registrar command to configure the registrar server.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 408 ip snmp agent Use the ip snmp agent command to enable the Simple Network Management Protocol (SNMP) agent. Synt ax Description No subcommands. Default V alues By default, the SNMP agen t is disa ble d .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 409 ip sntp source-interface <interfac e> The ip sntp source-interface command to use the specified interface’ s IP address as the source IP address for SNTP traf fic transmitted by the unit.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 410 ip [ssh-server <port> | telnet-server <port> ] Use the this command to specify alternate transmi ssion contro l protocol (TCP) ports for secure shell (SSH) and Telnet servers.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 411 ip subnet-zero The ip su bnet-zero command is the default operat ion and can not be disabled. This command signifies the router’s ability to route to subnet-zero subnets.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 412 ip t f tp source-interface <interface> Use the ip tftp source-interface command to use the specified interf ace’ s IP address as the source IP address for TFTP traffic transmitted by the unit.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 413 line [console | telnet | ssh] <li ne-number> <ending number> Use the line command to enter the line configuration for the specified console, Telnet, or secure shell (SSH) session.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 414 Command History Release 1.1 Command was introdu ced.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 415 lld p [minimum-transmit-interv al l reinitialization-delay l transmit-interval l ttl-multiplier] <numeric value> Use the lldp command to configure global settings that control the way LLDP functions.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 416 Usage Examples The following example set s the LLDP minimum transmit interval to 10 seconds: .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 417 logging console Use the logging console command to enable the AOS to log ev ents to all co nsoles . Use the no form of this command to disable co nsole logging.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 418 logging email address-list <email address> ; <email address> Use the logging emai.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 419 logging email exception -report address-list <email address> ; <email address> Us.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 420 logging email on Use the logging email on command to enable the AOS email ev ent notification feature.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 421 logging email priority-l evel [error | fat al | info | notice | warning] Use the logging email priority-level command to set the threshold for events sent to the addresses specified using the logging email address-list command.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 422 logging email receiver-ip <ip address> Use the logging email receiver-ip command to spe.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 423 logging email sender Use the logging email sender command to specify the sender in an outgoing email message. This name will appear in the Fr om field of the receiver ’ s inbox.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 424 logging email so urce-interface <interface> Use the logging email source-interface command to use the specified inte rface’ s IP address as the source IP address for email messages tr ansmitted by the unit.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 425 logging facility <facility type> Use the logging facility command to specify a syslog facility ty pe for the syslog serv er. Error messages meeting specified criteria are sent to the syslog server.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 426 Usage Examples The following example configures the sys log facility to the c ron facility ty.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 427 logging forwarding on Use the logging forwarding on command to enable the AOS syslog event feature.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 428 logging forwarding priori ty-level [error | fat al | info | notice | warning] Use the logging.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 429 logging forwarding receiver-ip <ip address> Use this logging forwarding receiver-ip com.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 430 logging forwarding source-interface <interface> Use the logging forwarding source-interface command to configure the spec ified interface ’ s IP address as the source IP address for the syslog ser ver to use when logging events.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 431 mac address-t able aging-time <aging time> Use the mac address-table aging-time command to set the length of time dynamic MAC addresses remain in the switch or bridge forwarding table.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 432 mac address-t able st atic <mac address> bridge <bridge id> interface <interface> Use the mac address-table static command to insert a static MAC address entry into the bridge forwarding table.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 433 power-supply shut down automatic Use the power-supply shutdown automati c command to enable the power supplies to auto matically shut down when the unit temperature exceeds the maximum operating temp erature.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 434 qos map <mapname> <se quence number> Use the qos map command to activ ate the QoS Map Command Set (wh ich allows you to create and/o r edit a QoS map).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 435 Usage Examples The following e xample demo nstrates basic setting s fo r a QoS map and assign.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 436 radius-server Use the radius-server command to configure several global RADIUS parameters. Most of these global defaults can be overridde n on a per-server basis.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 437 Command History Release 5.1 Command was introdu ced. Release 7.1 Added enable-usern ame selection. Functional Notes RADIUS servers (as defined with the radius-server co mmand) may have many optional p arameters.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 438 radius-server host Use the radius-server host to specify the parameters for a remote RADIUS server. At a minimum, the address (IP or DNS name) of the server must be given.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 439 route-map <map-name> [ permit | deny ] <sequence number> Use the rout e - ma p command to create a route map and ente r the Route Map Configuration command set.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 440 router bgp Use the router bgp command to enter the BGP Configuration mode. Refer to the BGP Configuration Command section for more information. Synt ax Description No subcommands.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 441 router osp f Use the router ospf command to activat e OSPF in the router an d to enter the OSPF Configuration mode. Refer to the section Router (OSPF) Configuratio n Command Set on page 1114 for more information.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 442 router pim-sp arse Use the router pim-sparse command to globally enable protocol-i ndependent multicast (PIM) on the unit and to enter the PIM Sparse Config uration mode.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 443 router rip Use the router rip command to enter the RIP Configur ation mode. Refer to the section Router (RIP) Configuration Command Set on page 1134 for more information.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 444 Now consider a route that was learned and does no t receive an update for 18 0 seconds.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 445 service p assword-encryption Use the service passw ord-encryption command to turn on global password protection. Use the no form of this command to retu rn to default settings.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 446 snmp-server chassis-id <id string> Use the snmp-server chassis-id command to specify an identifier for the Simple Network Management Protocol (SNMP) server.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 447 snmp-server community <community> view <viewname> [ro | rw] <listname> Use the snmp-server community command to specify a community stri ng to control access to the Simple Network Management Protocol (SNMP) information.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 448 snmp-server cont act [email | pa ge r | phone] <number> Use the snmp-server contact command to specify the email addre ss, pager number, or phone number.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 449 snmp-server cont act <“string”> Use the snmp-server contact command to specify the SNMP sysContact string. Us e the no form of this command to remove a configured contact.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 450 snmp-server enable trap s <trap type> [snmp] Use the snmp-server enable traps command to enable all Simple Network Management Protocol (SNMP) traps available on your system or specified using the <trap type> option.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 451 snmp-server host <address> trap s <community> <trap type> [snmp] Use the snmp-server host traps command to specify traps sent to an identified host.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 452 snmp-server host <address> trap s version <version> <community> <trap type> [snmp] Use the snmp-server host traps version command to specify traps sent to an identified host.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 453 snmp-server location <“string”> Use the snmp-server location command to specify the Simple Netw ork Management Protocol (SNMP) system location string.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 454 snmp-server source-interface <interface> Use the snmp-server source-inter face command to tell the AOS the inte rface type from which to expect the SNMP traps to originate.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 455 snmp-server view <viewname> <oid tree> [excluded | included] Use the snmp-server view command to create or modify a Simple Network Management Protocol (SNMP) view entry.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 456 sntp server <address or hostname> version <1-3> Use the sntp server command to set the hostname of the SNTP server as well as the version of SNTP to use.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 457 sp anning-tree edgeport bpdufilter default Use the spanning-tree edgeport bpdufilter default command to enable the BPDU filter on all ports by default.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 458 sp anning-tree edgeport bp duguard default Use the spanning-t ree edgeport bp dugu ard default command to ena ble the BPDU guard on all ports by default.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 459 sp anning-tree edgeport default Use the spanning-tree edgeport default command to configure all ports to be edgeports by default. Use the no form of this command to disable the setting.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 460 sp anning-tree forward-time <seconds> Use the spanning-tree forward-time command to specify the delay interval (in seconds ) when forwarding spanning-tree packets.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 461 sp anning-tree hello-time <seconds> Use the spanning-tree hello-time command to specify the delay inte rval (in seconds) between hello bridge protocol data units (BPDUs).
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 462 sp anning-tree max-age <seconds> Use the spanning-tree max-age command to specify the i.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 463 sp anning-tree mode [rstp | stp] Use the spanning-tree mode command to choose a spanning-tree mode of operat ion. Synt ax Description rstp Enables rapid sp anning-tree protocol.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 464 sp anning-tree pathcost method [short | long] Use the spanning-tree pathcost command to select a short or long pa thcost method used by the spanning-tree protocol.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 465 sp anning-tree priority <value> Use the spanning-tree priority command to set the priority for sp anning-tree interfaces.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 466 t acacs-server Use the tacacs-server command to customize setting for commun ication with T ACACS servers. Use the no form of this command to return to default setti ngs.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 467 thresholds [BES | CSS | DM | ES | LCV | LES | PCV | SEFS | SES | UAS] [15Min | 24Hr] <threshold count> Use the thresholds command to specify DS1 performan ce counte r thresholds.
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 468 thresholds SES 15Min 10 thresholds SES 24Hr 100 thresholds SEFS 15Min 2 thresholds SEFS 24Hr .
Command Refere nce Guide Global Configuration Mode Command Set 61200990L1-35E Copyright © 2005 ADTRAN 469 username <username> p assword <password> Use this command to configure th e u ser.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 470 L INE (C ONSOLE ) I NTERFACE C ONFIG C OMMAND S ET To activate the Line (Console) Inte rface Configuration mode, enter the line console 0 command at the Global Configuration mode prompt .
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 471 accounting commands [ <level> l <name> l default] Use the accounting commands command to assign AAA accounting methods to lines.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 472 authorization comman ds [ <level> l <name> l default] Use the authorization commands command to assign AAA authorization methods to lines.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 473 dat abit s [7 | 8] Use the databits command to set the number of databits per ch aracter for a terminal session. This value must match the configuration of your VT100 terminal or terminal emulator software.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 474 flowcontrol [none | sof tware in] Use the flowcontrol comma nd to set flow control for the line console. Synt ax Description none S pecifies no flow control.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 475 line-timeout <minutes> Use the line-timeout c ommand to specify the number of minute s a line session may remain inactive before the AOS terminates the session.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 476 login Use the login command to enable security lo gin on the line session requir ing the password configured using the password command. Use the no form of this command to disabl e the login feature.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 477 login authentication <aaa login li st> Use the login authentication command to specify the named AAA login lis t to use for authenticating users connecting on this line.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 478 login local-userlist Use the login local-userlist command to enable security login fo r the terminal sess ion requiring the usernames and passwords configured using the userna me/password G lobal Configuration comman d.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 479 p arity [even | mark | none | odd | space] Use the parity command to specify the type of parity used as error correction. This value must match the configuration of your VT100 terminal or terminal e mulator software.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 480 p assword [md5] <password> Use the password command to configure the pa ssword (with optional encryptio n) required on the line session when security login is enabled (using the login command).
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 481 speed <rate> Use the speed command to spec ify th e data rate for the CONSOLE port. This setting must match your VT100 terminal emulator or emulator software.
Command Refere nce Guide Line (Console) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 482 stopbit s [1 | 2] Use the stopbits command to set the number of stopbits per characte r for a terminal session. This value must match the configuration of your VT100 terminal or terminal emulator software.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 483 L INE (SSH) I NTERFACE C ONFIG C OMMAND S ET To activate the Line Secure Shell (SSH ) Interface Configuration mode, enter the line ssh command specifying a SSH session(s) at the Global Configuration mode prompt.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 484 access-class <listname> in Use the access-class in c ommand to restrict Secure Shell ( SSH) access using a configured access list. Received packets passed by the acces s list will be allo wed.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 485 accounting commands [ <level> l <name> l default] Use the accounting commands command to assign AAA accounting methods to lines. You must first turn AAA on for this command to become available.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 486 authorization comman ds [ <level> l <name> l default] Use the authorization commands command to assign AAA authorization methods to lines.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 487 line-timeout <minutes> Use the line-timeout c ommand to specify the number of minute s a line session may remain inactive before the AOS terminates the session.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 488 login Use the login command to enable security lo gin on the line session requir ing the password configured using the password command. Use the no form of this command to disabl e the login feature.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 489 login authentication <aaa login li st> Use the login authentication command to assign the named AAA login list to use for authenticating users connecting on this line.
Command Refere nce Guide Line (SSH) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 490 login local-userlist Use the login local-userlist command to check the local list of user n.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 491 L INE (T ELNET ) I NTERFACE C ONFIG C OMMAND S ET To activate the Line (Telnet) In terface Configuration mode, enter the line telnet command specifying a Telnet session(s) at the Global Conf iguration mode prompt.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 492 access-class <listname> in Use the access-class in command to res trict Telnet access using a configured access list. Receive d packets passed by the access list will be allowed.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 493 accounting commands [ <level> l <name> l default] Use the accounting commands command to assign AAA accounting methods to lines.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 494 authorization comman ds [ <level> l <name> l default] Use the authorization commands command to assign AAA authorization methods to lines.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 495 line-timeout <minutes> Use the line-timeout c ommand to specify the number of minute s a line session may remain inactive before the AOS terminates the session.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 496 login Use the login command to enable security lo gin on the line session requir ing the password configured using the password command. Use the no form of this command to disabl e the login feature.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 497 login authentication <aaa login li st> Use the login authentication command to specify the named AAA login lis t to use for authenticating users connecting on this line.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 498 login local-userlist Use the login local-userlist command to enable security login fo r the terminal sess ion requiring the usernames and passwords configured using the userna me/password G lobal Configuration comman d.
Command Refere nce Guide Line (Telnet) Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 499 p assword [md5] <password> Use the password command to configure the pa ssword (with optional encryptio n) required on the line session when security login is enabled (using the login command).
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 500 DSX-1 I NTERFACE C ONFIGURATION C OMMAND S ET To activate the DSX-1 Interface Configuration mode, enter the inte rface t1 command (and spe cify the DSX-1 port) at the Global Configuration mode prompt.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 501 coding [ami | b8zs] Use the coding command to configure the line coding for a DSX-1 physical interface. This setting must match the line coding supplied on the circuit by th e PBX.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 502 framing [d4 | esf] Use the framing command to config ure the framing format for the DSX-1 interface. This parameter should match the framing format se t on the external device.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 503 line-length <value> Use the line-length command to set the line build out (in feet or dB) for the DSX-1 interface. Use the no form of this command to re turn to the default value.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 504 loopback network [line | p ayload] Use the loopback network command to initiate a loo pback on the interface towa rd the network. Use the no form of this command to deactivate the loopback.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 505 loopback remote line [inband] Use the loopback remote line inband command to send a loop back code to the remote unit to initiate a line loopback.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 506 remote-loopback Use the remote-loopback command to configure the interface to respond to loopbacks initiated by a remote unit (or the service provider).
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 507 signaling-mode [message-orien ted | none | robbed-bit] Use the signaling-mode command to config ure the signaling type (robbed-bit for v o ice or clear channel for data) for the DS0s mapped to the DSX-1 port.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 508 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Netw.
Command Refere nce Guide DSX-1 Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 509 test-p attern [ones | zeros] Use the test-pattern command to activate the bu ilt-in pattern generator and begin sending the specified test pattern.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 510 E1 I NTERFACE C ONFIGURATION C OMMAND S ET To activate the E1 Interface Configuration mode, enter the interface e1 command (a nd specify the E1 port) at the Global Configuratio n mode prompt.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 511 clock source [internal | line | through] Use the clock source command to configure the source tim ing used for the interface. Us e the no form of this command to return to the default value.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 512 coding [ami | hdb3] Use the coding command to configure the line coding for the E1 physical interface. This setting must match the line coding supplied on th e circuit by the service provider.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 513 framing [crc4] Use the framing command to configure the f raming format fo r the E1 interface. Th is parameter should match the framing format provided by the se rvice provider or external device.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 514 loop-alarm-detect The loop-alarm-detect command enables detection of a lo op alarm on the E1 interface . Use the no form of this command to disable this feature.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 515 loopback network [line | p ayload] Use the loopback network command to initiate a loo pback on the interface towa rd the network. Use the no form of this command to deactivate the loopback.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 516 loopback remote v54 The loopback remote v54 command initiates an E1 remo te loopback test (with a V .54 loopback pattern). Use the no form of this command to disable this feature.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 517 remote-alarm [rai | ais] The remote-alarm command selects the alarm signaling type to be sent when a loss of frame is detected on the E1 receive signal.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 518 remote-loopback Use the remote-loopback command to configure the interface to respond to loopbacks initiated by a remote unit (or the service provider).
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 519 sa4tx-bit [0 | 1] The sa4tx -bit command selects the Tx value of Sa 4 in this E1 interface. Use the no form of this command to return to the default value of 1.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 520 show test-p attern Use the show test-pattern command to display results from test patterns .
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 521 snmp trap line-st atus Use the snmp trap line-status command to control the Simple Network .
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 522 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Network.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 523 snmp trap threshold-reached Use the snmp trap threshold-reache d command to cont rol the Si.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 524 t dm-group <group number> timeslots <1-31> speed [56 | 64] Use the tdm-group command to create a group of contiguous channels on this interface to be used during the cross-connect process.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 525 test-p attern [clear | in sert | ones| p215 | p220 | p51 1 | qrss | zeros] Use the test-pattern command to activate the bu ilt-in pattern generator and begin sending the specified test pattern.
Command Refere nce Guide E1 Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 526 ts 1 6 Use the ts16 command to enable timeslot 16 multiframe to be checked on the receive signal. Use the no form of this command to disable timeslot 16.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 527 E THERNET I NTERFACE C ONFIGURATION C OMMAND S ET There are four types of Ethernet interfaces associated with the AOS: • Basic Ethernet interfaces (e.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 528 The following comm a nd s are com mo n to multiple command sets and are covered in a centralized section of this guide.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 529 lldp receive on page 573 lldp send [management-address l port-descrip tion l system-c.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 530 access-policy <policyname> Use the access-policy comma nd to assign a specified access policy for the inbound traffi c to an interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 531 Create the access policy that contains the access list InWeb : (config)# ip policy-cl.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 532 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 533 arp arp a Use the arp arpa command to enable address resolution prot ocol (ARP) on the Ethernet interface. Synt ax Description arp a Sets st andard address resolution protocol fo r this interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 534 bandwid th <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 535 bridge-group <group#> Use the bridge-group command to assign an interface to th e specified bridge group. Use the no form of this command to remo ve the interface from the bridge group.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 536 crypto map < mapname > Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> S pecifies the crypto map name that you wish to assign to the interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 537 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated w ith the inter face on whic h the data is receiv ed.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 538 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 539 If your IP address does not change of ten or at all but you still want an easy name to remember it by (without having to purchase your own domain name), S tatic DNS service is ideal for y ou.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 540 encap sulation 802.1q Use the encapsulation 802.1q command to put the interface into 802.1q (VLAN) mode. Synt ax Description No subcommands.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 541 full-duplex Use the full-duplex command to configure the Ethernet interface for full-duplex operati on. This allows the interface to send and receiv e simultan eo us ly .
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 542 Usage Examples The following example configu res the Ethernet interface for full-dupl.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 543 half-duplex Use the half-duplex command to configure the Ethernet interface for half-duplex op erati on. This setting allows the Ethernet interface to e ither send or receive at any gi ven moment, but not simultaneously.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 544 ip access-group <listname> [in | out] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 545 ip address dhcp Use the ip address dhcp command to use Dynamic Ho st Configuration Protocol (DHCP) to obtain an address on the Ethernet interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 546 INTERF ACE SPECIFIC INFO is only used for Frame Relay interfaces and can be determined using the following: FR_PORT#: Q.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 547 Functional Notes Dynamic Host Configuratio n Protocol (DHCP) allows interfac es to acquire a dynamic ally assigned IP address from a configured DHCP server on the n etwor k.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 548 ip address <address> <mask> secondary Use the ip address command to define an IP address on the sp ecified interface (only one primary address is allowed).
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 549 ip dhcp release Use the ip dhcp release command to transmit a messag e to the DHCP server requ esting termination of the IP address lease on tha t interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 550 ip dhcp renew Use the ip dhcp renew comma nd to transmit a message to the DHCP server requesting renewal of the IP address lease on that interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 551 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 552 Usage Examples The following example forwar ds all DNS broadcas t traf fic to the DNS server with IP address 192.33.5.99 : (config)# ip forward-protocol ud p domain (config)# interface eth 0/1 (config-eth 0/1)# ip helper-addres s 192.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 553 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV anta 300, 3000, 4000, and 500 0 and T otal Access 900 Series unit s.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 554 Usage Examples The following example sets the qu ery message interval on the interfac.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 555 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface, and to place it in multi cast stub downstream mode.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 556 ip mcast-stub helper-address <ip address> Use the ip mcast-stub helper-address command to specify an IP address toward which IGMP host reports and leave messages are forwarded.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 557 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 558 ip osp f Use the ip ospf command to customize O SPF settings (if needed).
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 559 ip osp f authentication [message-digest | null] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 560 ip osp f network [broad cast | point-to-point] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Set s the network type for broadcast.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 561 ip pim sp arse-mode Use the ip pim sparse-mode command to enable protoc ol-independent multicast (PIM) sparse mode for this interface. Use the no form of this command to disable PIM sparse mode.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 562 ip pim-sp arse dr-priority <priority number> Use the ip pim-sparse dr-priority command to specify the priority for the designated router (DR).
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 563 ip pim-sp arse hello-timer <time> Use the ip pim-sparse hello-timer command to specify protocol-indepen dent multicast (PIM) sparse hello timer period.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 564 ip pim-sp arse nbr-timeout <time> Use the ip pim-sparse nbr-timeout command to specify protocol-ind ependent multicast (PIM) sparse neighbor timeout.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 565 ip pim-sp arse override-interval <time> Use the ip pim-sparse over ride-interval command to specify the protoc ol-independent multicast (PIM) sparse join/prune override interval.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 566 ip pim-sp arse pr op agation-delay <time> Use the ip pim-sparse propagation-delay command to specify protoc ol-independent multicast (PIM) sparse join/prune propagation delay.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 567 ip policy route-map <policy name> Use the ip policy route-map command to assign a policy route- map to this interface. Use the no form of this command to remove the route-map policy.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 568 ip proxy-arp <address> <s ubnet mask> Use the ip proxy-arp command to enable proxy Address Resolutio n Protocol (ARP) on the interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 569 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 570 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 571 ip route-cache Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 572 ip unnumbered <interface> Use the ip unnumbered command to use the IP address assigned to the specified interface for all IP processing on the active interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 573 lld p receive Use the lldp receive command to allow LLDP packets to be received on this interface. Synt ax Description No subcommands. Default V alues By default, all interfaces are configured to send and receive LLDP packets.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 574 lld p send [management-addre ss l port-description l system-cap abilities l system-de.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 575 Usage Examples The following example configu res Ethernet interface 0/1 to tran smit .
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 576 mac-address <address> Use the mac-address command to specify the Media Access Cont rol (MAC) address of the unit. Only the last three values of the MAC address can be mo dified.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 577 max-reserved-bandwidth <percent> Use the max-reserve d-bandwidth command to define the maximum amount o f interface bandwidth reserved for Quality of Service (QoS).
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 578 mtu <size> Use the mtu command to configure the ma ximum transmit unit (MTU) size for the active interface. Use the no form of this command to re turn to the default value.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 579 qos-policy out <mapname> Use the qos-policy out command to apply a previously -configu red QoS map to an interface. Use the no form of this command to remove the map from the interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 580 Usage Examples The following example applies th e QoS map VOICEMAP to the Etherne t i.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 581 snmp trap Use the snmp trap command to enable all supported Simple Network Management Proto col (SNMP) traps on the interface. Synt ax Description No subcommands.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 582 snmp trap link-st atus Use the snmp trap link-status command to control the SNMP va riable ifLinkUpDownTrapEnable (RFC2863) to enable (or disable) the interface to sen d SNMP traps when there is an interface status change.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 583 sp anning-tree bpdufilter [enable | disable] Use the spanning-tree bpdufilter command to enable or disable the BPDU filter on a specific interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 584 sp anning-tree bp duguard [enable | disable] Use the spanning-tree bpduguard command to enable or disa ble the BPDU guard on a specific interfa ce.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 585 sp anning-tree edgeport Use the spanning-tree edgeport command to configure the interface to be an edgeport. This command overrides the related Global setting (refer to span nin g-tree edgeport default on page 459 ).
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 586 sp anning-tree link-type [auto | point-to-point | shared] Use the spanning-tree link-type command to configure th e spanning tree protocol link type for each interface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 587 sp anning-tree p athcost method [short | long] Use the spanning-tree pathcost command to select a short or long method used by the spa nning-tree protocol.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 588 sp anning-tree port-priority <priority level> Use the spanning-tree port-priority command to select the prio rity level of this inte rface.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 589 speed [10 | 100 | au to | nonegotiate] Use the speed command to configure th e speed of an Ethernet interface. Use the no form of this command to return to the default value.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 590 traffic-shape rate <rate> <burstrate> Use the traffic-shape rate command to specify and enforce an ou tput bandwidth for Et hernet and VLAN interfaces.
Command Refere nce Guide Ethernet Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 591 vlan-id <vlan id> [native] Use the vlan-id command to set a VLAN ID for th e Ethernet interface. Use the no form of this command to remove an entry.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 592 G .703 I NTERFACE C ONFIGURATION C OMMAND SET To activate the G.703 Interface Configuration mode, enter the interface e1 comman d (and spec ify the G.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 593 coding [ami | hdb3] Use the coding command to configure the line coding for the G.703 physical interfa ce. This setting must match the line coding supplied on the circuit by th e PBX.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 594 framing [crc4] Use the framing command to co nfigure the frami ng format for the G.703 inte rface. This parameter should match the framing format set on the external device.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 595 loopback network [line | p ayload] Use the loopback network command to initiate a loo pback on the interface towa rd the network. Use the no form of this command to deactivate the loopback.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 596 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Netwo.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 597 test-p attern [ones | zeros] Use the test-pattern command to activate the bu ilt-in pattern generator and begin sending the specified test pattern.
Command Refere nce Guide G.703 Interface Configuration Command set 61200990L1-35E Copyright © 2005 ADTRAN 598 ts 1 6 Use the ts16 command to enable timeslot 16 multiframe to be checked on the receive signal. Use the no form of this command to disable timeslot 16.
Command Refere nce Guide HSSI Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 599 HSSI I NTERFACE C ONFIGURATION C OMMAND S ET To activate the HSSI Interface Configuration mode, enter the inte rface hssi command at the Global Configuration mode prompt.
Command Refere nce Guide HSSI Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 600 external-loopback-request Use the external-loopback-request command to enable LC (loopbac k circuit C) input to cont rol loopbacks toward the network.
Command Refere nce Guide HSSI Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 601 loopback [dce | d te | line | remote | none] Use the loopback command to initiate or remove a loopback. Synt ax Description dce Initiates a loopback on the DCE.
Command Refere nce Guide HSSI Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 602 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Netwo.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 603 T1 I NTERFACE C ONFIGURAT ION C OMMAND S ET To activate the T1 Interface Configuration mode, enter the interface t1 command at the Global Configuration mode prompt.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 604 clock source [internal | line | through | through <interface id> ] Use the clock source command to configure the source tim ing used for the interface.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 605 coding [ami | b8zs] Use the coding command to configure the line co ding for a T1 physical interface. This setting must match the line coding supplied on the circuit by the service provider.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 606 fdl [ansi | att | none] Use the fdl command to configure th e format for the facility data link (FDL) channel on the T1 circuit. FDL channels are only available on point-to-point circui ts.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 607 framing [d4 | esf] Use the framing command to config ure the framing format fo r the T1 interface. Th is parameter should match the framing format supplied by your network provider.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 608 lbo [long <-22.5, -15, -7.5, 0> | short <0-655> ] Use the lbo command to configure the line build ou t (LBO) for the T1 interface.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 609 loopback network [line | p ayload] Use the loopback network command to initiate a loo pback on the interface towa rd the network. Use the no form of this command to deactivate the loopback.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 610 loopback remote li ne [fdl | inband] Use the loopback remote line command to send a loopback code to the remote unit to initiate a line loopback.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 611 loopback remote p ayload Use the loopback remote payload command to send a loopback code to the remote unit to initiate a payload loopback. A payl oad loopback is a 1.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 612 remote-alarm [rai] The remote-alarm command selects the alarm signaling type to be sent when a loss of frame is detected on the T1 receive signal.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 613 remote-loopback Use the remote-loopback command to configure the interface to respond to loopbacks initiated by a remote unit (or the service provider).
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 614 show test-p attern Use the show test-pattern command to display results from test patterns.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 615 snmp trap line-st atus Use the snmp trap line-status command to control the Simple Network.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 616 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Networ.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 617 snmp trap threshold-reached Use the snmp trap threshold-reache d command to cont rol the S.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 618 t dm-group <group number> timeslots <1-24> speed [56 | 64] Use the tdm-group command to create a group of contiguous DS 0s on this interface to be used during the cross-connect process.
Command Refere nce Guide T1 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 619 test-p attern [clear | insert | ones | p215 | p220 | p51 1 | qrss | zeros] Use the test-pattern command to activate the bu ilt-in pattern generator and begin sending the specified test pattern.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 620 T3 I NTERFACE C ONFIGURAT ION C OMMAND S ET To activate the T3 Interface Configuration mode, enter the interface t3 command at the Global Configuration mode prompt.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 621 clock source [local | loop] Use the clock source command to configure the source timing us ed for the interface. The clock specifie d using the clock source command is also the syst em master clock.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 622 coding [b3zs] Use the coding command to configure the line co ding for a T3 physical interface. This setting must match the line coding supplied on the circuit by the service provider.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 623 framing [m13 | cbit] Use the framing command to config ure the network framing format for a T3 physical interface. Synt ax Description m13 Configures th e inte rf ac e fo r M1 3 fra m ing .
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 624 line-length [ short | long] Use the line-length command to configure the line leng th for a T3 physical interface. Synt ax Description short Configures th e line length fo r a distance of 0 to 225 feet of cable.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 625 loopback network [line | p ayload] Use the loopback network command to initiate a loca l T3 loopback on the inte rface toward the network. Use the no form of this command to deactivate the loopback.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 626 loopback remote [line | p ayload] Use the loopback remote command to initiate a loopb ack test on the T3 interface that sends a remote loopback code out the T3 circuit to loop up the far end.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 627 remote-loopback Use the remote-loopback command to configure the T3 interface to be looped from the far end (remote device, telco, etc.). Use the no form of this command to disable this feature.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 628 show [bert] The show bert command displays the results for the bit error rate test (BER T) conducted o n the T3 interface. Synt ax Description No subcommands.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 629 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Networ.
Command Refere nce Guide T3 Inte rfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 630 test-p attern [clear | insert | ones | p215 | p223 | zeros] Use the test-pattern command to activate the built-in pattern ge nerator and begin sending the selected test pattern toward the network.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 631 D EMAND I NTERFACE C ONFIGURATION C OMMAND S ET To activate the Demand Interface Configuration mode, enter the interface d e mand command at the Global Configuration mode prompt .
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 632 fair-queue <threshold> on page 650 fast-idle <seconds> on page 651 hold-que.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 633 access-policy <policyname> Use the access-policy comma nd to assign a specified access policy for the inbound traffi c to an interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 634 Create the access policy that contains the access list InWeb : (config)# ip policy-clas.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 635 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 636 bandwid th <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 637 called-number <DNIS number> Use the called-number command to link calls to specific in terfaces based on their dialed number identification service (DNIS) numbers.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 638 caller-number <CLID number> Use the caller-number command to link calls to specific interfaces based on it’s caller ID (CLID) number.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 639 connect-mode [answer | originate | either] Use the connect-mode command to configure the interface to only answer calls, only orig inate calls, or to both answer and originate calls.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 640 connect-order [last-successful | round-robin | sequential] Use the connect-order command to specify th e starting poi nt in the connection seque nce for each sequence activation.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 641 connect-sequence Use the connect-sequence command to provide instructions to th e interface on how to use the resource pool and telephon e numbers to connect to dem and destinations.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 642 Usage Examples The following example instruct s demand interface 1 to place the call us.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 643 connect-sequence attempt s <value> Use the connect-sequence attempts command to limit the number of times the connec t sequence will cycle when its entries are unable to establish a conn ection.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 644 connect-sequence interface-recovery [retry-interval <seconds> | max-retries <v.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 645 crypto map <mapname> Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> Assigns a crypto m ap name t o the inter face.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 646 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated w ith the inter face on whic h the data is receiv ed.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 647 demand-hold-queue <packet s> timeout <seconds> Use the deman d-hold-que ue timeout command to set the number and leng th of time interesting packets will be held while a connecti on is being made.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 648 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 649 dyndns-st atic - The S tatic DNS service is similar to Dynamic DNS service, in that it allows a hostname such as yourname.dyn dns.org to point to your IP a ddress.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 650 fair-queue <threshold> Use the fair-queue command to enable weighted fair qu euing (WFQ) on an interface. Use the no for m of this command to disable WFQ and en able FIFO queueing for an interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 651 fast-idle <seconds> Use the fast-idle command to set the amount of time the deman.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 652 hold-queue <queue size> out Use the hold-queue out command to change the overall size of an interfa ce's WAN output queue.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 653 idle-timeout <seconds> Use the idle-timeout command to set the amount of time the interface link/bund le will remain up in the absence of interesting traffic.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 654 ip access-group <listname> [in | out] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 655 ip address negotiated [no-default] Use the ip address negotiated command to allow the interface to ne gotiate (i.e., be assigned) an IP address from the far end PPP connection.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 656 ip address <address> <mask> secondary Use the ip address command to define an IP address on the sp ecified interface. Use the optional keyword secondary to define a secondary IP address .
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 657 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 658 Usage Examples The following example forwar ds all DNS broadcas t traf fic to the DNS server with IP address 192.33.5.99 : (config)# ip forward-protocol ud p domain (config)# interface demand 1 (config-demand 1)# ip helper -address 192.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 659 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV anta 1000R, 3000, 4000, an d 5000 Series unit s.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 660 Command History Release 7.1 Command was introdu ced.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 661 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface and place it in multicast stub downstream mode.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 662 ip mcast-stub helper-enable Use the ip mcast-stub helper-enable comma nd to assign the ip mcast-stub helper-address as the IGMP proxy. Use the no form of this command to disable.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 663 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 664 ip osp f Use the ip ospf command to customize O SPF settings (if needed). Applicable Plat forms This command applies to the NetV anta 1000R, 3000, 4000, an d 5000 Series unit s.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 665 ip osp f authentication [message-digest | null] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 666 ip osp f network [broad cast | point-to-point] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Set s the network type for broadcast.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 667 ip policy route-map <mapname> Use the ip policy route-map command to associate a route map with a network interface source. Use the no form of this command to disable this feature.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 668 ip proxy-arp <address> <s ubnet mask> Use the ip proxy-arp to enable proxy Address Resolution Protocol (ARP) on th e interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 669 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 670 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 671 ip route-cache Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 672 ip unnumbered <interface> Use the ip unnumbered command to use the IP address assigned to the specified interface for all IP processing on the active interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 673 keep alive <seconds> Use the keepalive command to enable the transmission of keep alive pa ckets on the interface and specify the time interval in seconds between transmitted packets.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 674 lld p receive Use the lldp receive command to allow LLDP packets to be received on this interface. Synt ax Description No subcommands. Default V alues By default, all interfaces are configured to send and receive LLDP packets.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 675 lld p send [management-addre ss l port-description l system-cap abilities l system-desc.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 676 Usage Examples The following example configu res the demand interface to tr ansmit LLDP.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 677 match-interesting [list <acl name> | reverse list <acl name> ] [in | out] U.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 678 mtu <size> Use the mtu command to configure the ma ximum transmit unit (MTU) size for the active interface. Use the no form of this command to return to the default value.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 679 peer default ip address <address> Use the peer default ip address command to specify the default IP address of the remote end of this interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 680 ppp authentication [chap | eap | p ap] Use the ppp authentication command to specify the authentication protocol on the PPP virtual interface that the peer should use to authenticate itself.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 681 Several examp le sce na r ios ar e giv en below fo r c lar ity . Configuring P AP Example 1: Only the local rout er requires the pee r to authenticate it self.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 682 Several examp le sce na r ios ar e giv en below fo r c lar ity . Configuring CHAP Example 1: Only the loca l ro uter requires the peer to authenticat e it self.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 683 Configuring CHAP Example 4: Using the ppp chap p assword command as an alternat e solution.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 684 ppp chap hostname <hostname> Use the ppp chap hostname command to configure an alternate hostname for CHAP PPP authentication. Use the no form of this command to remove a configur ed hostname.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 685 ppp chap p assword <password> Use the ppp chap password command to configure an alternate p assword when the peer requires CHAP PPP authentication.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 686 ppp multilink [fragment ation | interleave] Use the ppp multilink command to enable multilink PPP (MPPP) operation on an existing PPP interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 687 ppp p ap sent-username <username> pa ssword <password> Use the ppp pap sent-username/password command to configure a username and password when the peer requires PAP PPP authentication.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 688 qos-policy out <mapname> Use the qos-policy out command to apply a previously -configu red QoS map to an interface. Use the no form of this command to remove th e map from the interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 689 resource pool <pool name> Use the resource pool command to associate a resource pool with the demand interface. No more than one resource pool may be associated with an interface.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 690 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Net.
Command Refere nce Guide Demand Interface Conf iguration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 691 username <username> password <p assword> Configures the userna me and password of the peer to us e for demand authentication.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 692 F RAME R ELAY I NTERFACE C ONFIG C OMMAND S ET To activate the Frame Relay Interfa ce Configuration mode, enter the interface frame-relay command at the Global Config uration mode prompt.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 693 bandwidth <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 694 encap sulatio n frame-relay iet f Use the encapsulation frame-relay ietf command to configure the encapsulation on a virtual Frame Relay interface as IETF (RFC1490).
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 695 fair-queue <threshold> Use the fair-queue command to enable weighted fair qu euing (WFQ) on an interface. Use the no for m of this command to disable WFQ and en able first-in-first-out (FIFO) qu eueing for an interface.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 696 frame-relay int f-type [dce | d te | nni] Use the frame-relay intf-type command to define the Frame Relay signaling role needed for the endpoint.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 697 frame-relay lmi-n391dce <polls> Use the frame-relay lmi-n391dce command to set the N391 full st atus polling counter for the DCE endpoint.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 698 frame-relay lmi-n391d te <polls> Use the frame-relay lmi-n391dte command to set the N391 full status polling counter for the DTE endpoint.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 699 frame-relay lmi-n392dce <threshold> Use the frame-relay lmi-n392dce command to set the N392 error threshold for the DCE endpoint. Typical applications should leave the defa ult value for this setting.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 700 frame-relay lmi-n392d te <threshold> Use the frame-relay lmi-n392dte command to set the N392 error thr eshold for the DTE endpoint. Typical applications should leave the defa ult value for this setting.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 701 frame-relay lmi-n393dce <counter> Use the frame-relay lmi-n393dce to set the N393 LMI moni tored ev ent counter for the DCE endpoint. Typical applications should leave the de fault value for this counter.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 702 frame-relay lmi-n393d te <counter> Use the frame-relay lmi-n393dte command to set the N393 LMI mo nitored event counter for the DTE endpoint.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 703 frame-relay lmi-t391d te <seconds> Use the frame-relay lmi-t391dte command to set the T391 signal polling timer for the DTE endpoint. Typical applications should leave the default value for this timer.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 704 frame-relay lmi-t392dce <seconds> Use the frame-relay lmi-t392dce command to set the T392 polling verification timer for the DCE endpoint.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 705 frame-relay lmi-type [ansi | auto | cisco | none | q933a] Use the frame-relay lmi-type command to de fine the Frame Relay signal ing (LMI) type.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 706 frame-relay multilink [ack <seconds> | bandwid th-class <class> <threshold> | hello <seconds> | retry <number> ] Use the frame-relay multilink command to enable the Frame Re lay multilink interfa ce.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 707 Usage Examples The following example enables the Frame Relay mu ltilink interface and sets.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 708 hold-queue <queue size> out Use the hold-queue out command to change the overall size of an interfa ce's WAN output queue.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 709 max-reserved-bandwidth <percent> Use the max-reserve d-bandwidth command to define the maximum amount o f interface bandwidth reserved for Quality of Service (QoS).
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 710 qos-policy out <mapname> Use the qos-policy out command to apply a previously -configu red QoS map to an interface. Use the no form of this command to remove the map from the interface.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 711 Usage Examples The following example applies th e QoS map VOICEMAP to the Frame Relay inte.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 712 snmp trap Use the snmp trap command to enable all supported Simple Network Management Proto col (SNMP) traps on the interface. Synt ax Description No subcommands.
Command Refere nce Guide Frame Relay Interface Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 713 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Networ.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 714 F RAME R ELAY S UB -I NTERFACE C ONFIG C OMMAND S ET To activate the Frame Relay Sub-Inte rface Configuration mode, enter the interface frame-relay command (and specify a sub-interface) at the Global Configuration m od e pro mp t .
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 715 access-policy <policyname> Use the access-policy command to assign a specified access policy for the inbound tra ffic on an interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 716 Create the access policy that contains the access list InWeb : (config)# ip policy-cl.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 717 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 718 bandwidth <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 719 bridge-group <group#> Use the bridge-group command to assign an interface to the speci fied bridge group. This c ommand is supported on all Ethernet interfaces, PPP virtual inte rfaces, and Frame Relay virtual sub-interfaces.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 720 crypto map <mapname> Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> S pecifies the crypto map name that you wish to assign to the interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 721 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated w ith the inter face on whic h the data is receiv ed.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 722 dial-backup auto-backup Use the dial-backup auto-backu p command to configure the Frame Rela y sub-i n terface to automatically attempt a dial-backup up on failure.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 723 dial-backup auto-restore Use the dial-backup auto-restore command to configure the interface to automatically discontinue dial-backup when all network cond itions are operational.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 724 dial-backup backup-delay <seconds> Use the dial-backup backup-delay command to configure the amount of time the router will wait after t he failure condition is recogniz ed before attempting to backup the link.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 725 dial-backup call-mode [answer | answer-always | originate | originate-answer | or igi.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 726 interface t1 1/1 coding b8zs framing esf clock source line tdm-group 1 timeslots 1-24 no shutdown ! interface fr 1 point-to-point frame-relay lmi-type ansi no shutdown cross-conn ect 1 t1 1/ 1 1 fr 1 ! interface fr 1.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 727 ! interface fr 1.100 point-to-po int frame-relay interface-dlci 100 ip address 10.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 728 dial-backup connect-timeout <seconds> Use the dial-backup connect-timeout command to specify the number of se conds to wait for a connection after a call is attempted before trying to call again or dialing a different number .
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 729 dial-backup force [backup | primary] Use the dial-backup force command to manually overri de the automatic dia l-ba c ku p feature.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 730 dial-backup maximum-retry <attempts> Use the dial-backup maximum-retry command to select the number of ca lls the rout er w ill make when attempting to backup a link.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 731 dial-backup number <digit s> [analog | digit al-56k | digital 64k] <isdn min.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 732 dial-backup priority <value> Use the dial-backup priority command to select the backup priority for this interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 733 dial-backup randomize-timers Use the dial-backup randomize-timers command to randomize the call ti mers to minimize potential contention for resources.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 734 dial-backup redial-delay <seconds> Use the dial-backup redia l-delay command to configure the delay afte r an unsuccessful call until the call will be re-tried.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 735 dial-backup restore-delay <seconds> Use the dial-backup restore-delay command to configure the amount of time the router will wait after the network is restored before disconnecting the backup lin k and reverting to the primary.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 736 dial-backup schedule [day | enable-time | disable-time] Use the dial-backup schedule command to set the time of day that backup will be enabled.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 737 dial-backup shut down Use the dial-backup shutdown command to deactivate all dial-b ackup functionality in the unit.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 738 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 739 If your IP address doesn't c hange often or at all, but you still want an easy name to remember it by (without having to purchase your own domain na me) S tatic DNS service is ideal for you.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 740 frame-relay bc <committed burst value > Use the frame-relay bc command to set the b c (committed burst) value for a Frame Relay sublink.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 741 frame-relay be <excessive burst value > Use the frame-relay be command to set the b e (excessive burst) value for a Frame Relay sublink.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 742 frame-relay fragment <threshold> Use the frame-relay fragment command to set the FRF.12 fra gmentation threshold. Use the no form of this command to erase th e configured threshold.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 743 frame-relay interface-dlci <dlci > Use the frame-relay interface-dlci command to configure the Data Link Connection Identifier (DLCI) for the Frame Relay sub-interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 744 ip access-group <listname> [ in | out ] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 745 ip address dhcp Use the ip address dhcp command to use Dynamic Ho st Configuration Protocol (DHCP) to obtain an address on the interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 746 INTERF ACE SPECIFIC INFO is only used for Frame Relay interfaces and can be determined using the following: FR_PORT#: Q.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 747 Functional Notes DHCP allows interfaces to ac quire a dynamically assigned IP address from a configured DHCP server on the network. Many Internet Service Providers (ISPs) require the use of DHCP when connecting to their services.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 748 ip address <address> <mask> secondary Use the ip address command to define an IP address on th e specified interface. Use the optional secondary keyword to define a secondary IP address.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 749 ip dhcp [release | renew] Use the ip dhcp command to release or renew the DHCP IP ad dress. This command is only applicable when using DHCP for IP address assignment.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 750 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 751 Usage Examples The following example forwar ds all DNS broadcas t traf fic to the DNS server with IP address 192.33.5.99 : (config)# in terface frame-re lay 1.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 752 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV anta 1000R, 3000, 4000, an d 500 0 and T otal Access 900 Series unit s.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 753 Usage Examples The following example sets the qu ery message interval on the interface to 200 milliseconds: (config)# in terface frame-re lay 1.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 754 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface and place it in multicast stub downstream mode.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 755 ip mcast-stub helper-enable Use the ip mcast-stub helper-enable comma nd to assign the ip mcast-stub helper-address as the IGMP proxy. Use the no form of this command to disable.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 756 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 757 ip ospf Use the ip ospf command to customize O SPF settings (if needed).
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 758 ip ospf authentication [message-digest | null] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 759 ip ospf network [broad cast | point-to-point] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Set s the network type for broadcast.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 760 ip pim sp arse-mode Use the ip pim sparse-mode command to enable protoc ol-independent multicast (PIM) sparse mode for this interface. Use the no form of this command to disable PIM sparse mode.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 761 ip pim-sp arse dr-priority <priority number> Use the ip pim-sparse dr-priority command to specify the priority for the designated router (DR).
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 762 ip pim-sp arse hello-timer <time> Use the ip pim-sparse hello-timer command to specify protocol-indepen dent multicast (PIM) sparse hello timer period.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 763 ip pim-sp arse nbr-timeout <time> Use the ip pim-sparse nbr-timeout command to specify protocol-ind ependent multicast (PIM) sparse neighbor timeout.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 764 ip pim-sp arse override-interval <time> Use the ip pim-sparse over ride-interval command to specify the protoc ol-independent multicast (PIM) sparse join/prune override interval.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 765 ip pim-sp arse pr op agation-delay <time> Use the ip pim-sparse propagation-delay command to specify protoc ol-independent multicast (PIM) sparse join/prune propagation delay.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 766 ip policy route-map <policy name> Use the ip policy route-map command to assign a policy route- map to this interface. Use the no form of this command to remove the route-map policy.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 767 ip proxy-arp <address> <s ubnet mask> Use the ip proxy-arp to enable proxy Address Resolution Protocol (ARP) on th e interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 768 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 769 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 770 ip route-cache <address> Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 771 ip unnumbered <interface> Use the ip unnumbered command to use the IP address assigned to the specified interface for all IP processing on the active interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 772 lld p receive Use the lldp receive command to allow LLDP packets to be received on this interface. Synt ax Description No subcommands. Default V alues By default, all interfaces are configured to send and receive LLDP packets.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 773 lld p send [management-addre ss l port-description l system-cap abilities l system-de.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 774 Usage Examples The following example configu re s the Frame Relay sub-in terface to transmit LLDP packets containing all enabled info rmation types: (config)# in terface frame-re lay 1.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 775 mtu <size> Use the mtu command to configure the ma ximum transmit unit (MTU) size for the active interface. Use the no form of this command to re turn to the default value.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 776 sp anning-tree bp dufilter [enable | disable] Use the spanning-tree bpdufilter command to block BPDUs from bein g transmitted and re ceived on this interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 777 spanning-tree bpduguard [enable | disable] Use the spanning-tree bpduguard command to block BPDUs from being rece ived on this inte rface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 778 spanning-tree edgeport Use the spanning-tree edgeport command to set this in terface to be an edgeport. This command overrides the Global setting (refer to spanning-tree edgeport def ault on p age 459 ).
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 779 spanning-tree link-type [auto | point-to-p oint | shared] Use the spanning-tree link-type command to configure the spanning -tree protocol link type for an interface.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 780 spanning-tree path-cost <value> Use the spanning tree path-cost command to assign a cost to a bridge group that is us ed when co mputin g the spanning-t ree root path.
Command Refere nce Guide Frame Relay Sub-Interf ace Config Command Set 61200990L1-35E Copyright © 2005 ADTRAN 781 spanning-tree priority <value> Use the spanning-tree priority command to select the priority level of a port associa ted with a bridge.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 782 HDLC C OMMAND S ET To activate the HDLC mode, enter the interface hdcl command at the Global Configuration mode prompt.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 783 max-reserved-bandwidth <percent> on page 841 mtu <size> on page 842 qos-policy out <mapname> on .
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 784 access-policy <policyname> Use the access-policy command to assign a specified access policy for the inbound tra ffic on an interface. Use the no form of this command to remove an access policy association.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 785 Create the access policy that contains the access list InWeb : (config)# ip policy-class UnT rusted (config-policy.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 786 All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem. This allows for configurations to deny packets on a specified interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 787 alias link <“text”> Each configured HDLC interface (when referenced u sing SNMP) contains a link (physi cal port) and a bundle (group of links).
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 788 bandwidth <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 789 bridge-group <group#> Use the bridge-group command to assign an interface to th e specified bridge group. Use the no form of this command to remo ve the interface from the bridge group.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 790 crypto map <mapname> Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> Enter the crypto ma p nam e that you wish to assign to the interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 791 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated with the interface on which the dat a is received.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 792 dial-backup auto-backup Use the dial-backup auto-backup command to configure the PPP inte rface to automatically attempt a dial-backup upon failure.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 793 dial-backup auto-restore Use the dial-backup auto-restore command to configure the interface to automatically discontinue dial-backup when all network cond itions are operational.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 794 dial-backup backup-delay <seconds> Use the dial-backup backup-delay command to configure the amount of time the router will wait after t he failure condition is recogniz ed before attempting to backup the link.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 795 dial-backup call-mode [answer | answer-always | originate | originate-answer | or iginate-answer-always] Use the d.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 796 interface t1 1/1 coding b8zs framing esf clock source line tdm-g roup 1 timeslots 1-24 no shutdown ! interface ppp 1 ip address 10.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 797 no shutdown cross-conn ect 1 t1 1/1 1 p pp 1 ip address 10.1.1.1 25 5.255.255.252 dial-backup call-mode answer dial-backup number 5 55-8888 analog ppp 2 ! interface ppp 2 description connection fo r remote 3200 dialin for backup ip address 10.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 798 dial-backup connect-timeout <seconds> Use the dial-backup connect-timeout command to specify the number of se conds to wait for a connection after a call is attempted before trying to call again or dialing a different number .
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 799 dial-backup force [backup | primary] Use the dial-backup force command to manually overri de the automatic dia l-ba c ku p feature. This can be used to force a link into backup to allow maintenance to be perfo rmed on the prim ary link without disrupting data.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 800 dial-backup maximum-retry <attempts> Use the dial-backup maximum-retry command to select the number of ca lls the rout er w ill make when attempting to backup a link.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 801 dial-backup number <digit s> [analog | digit al-56k | digital 64k] <isdn min chan> <isdn max chan> <interface> Use the dial-backup number command to configure the phone number and the call type the router will dial upon network failure.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 802 dial-backup priority <value> Use the dial-backup priority command to select the backup priority for this interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 803 dial-backup randomize-timers Use the dial-backup randomize-timers command to randomize the call ti mers to minimize potential contention for resources. Use the no form of this command to return to the default value.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 804 dial-backup redial-delay <seconds> Use the dial-backup redia l-delay command to configure the delay afte r an unsuccessful call until the call will be re-tried.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 805 dial-backup restore-delay <seconds> Use the dial-backup restore-delay command to configure the amount of time the router will wait after the network is restored before disconnecting the backup lin k and reverting to the primary.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 806 dial-backup schedule [day | enable-time | disable-time] Use the dial-backup schedule command to set the time of day that backup will be enabled. Use this command if backup is desired only during n ormal busin ess hours and on specific days of the week.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 807 dial-backup shut down Use the dial-backup shutdown command to deactivate all dial-b ackup functionality in the unit.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 808 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 809 If your IP address doesn't c hange often or at all, but you still want an easy name to remember it by (without having to purchase your own domain na me) S tatic DNS service is ideal for you.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 810 fair-queue <threshold> Use the fair-queue command to enable weighted fair qu euing (WFQ) on an interface. Use the no for m of this command to disable WFQ and enable FIFO (firs t-in-first-out) queueing fo r an interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 811 hold-queue <queue size> out Use the hold-queue command to change the overall size of an interface's WAN output queue. Synt ax Description <queue size> The total numbe r of packet s the output queue can contain befor e p ackets are dropped.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 812 ip access-group <listname> [ in | out ] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 813 ip address <address> <mask> secondary Use the ip address command to define an IP address on th e specified interface. Use the optional secondary keyword to define a secondary IP address.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 814 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 815 Usage Examples The following example forwar ds all DNS br oadcast traf fic to the DNS server with IP address 192.33.5.99: (config)# ip forward-protocol ud p domain (config)# interface hdlc 1 (config-hdlc 1)# ip helper-address 192.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 816 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV ant a 300, 1000R, 300 0, 4000, and 5000 a nd T otal Access 900 Series units.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 817 Command History Release 9.1 Command was introdu ced. Usage Examples The following example sets the qu ery message .
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 818 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface and place it in multicast stub downstream mode.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 819 ip mcast-stub helper-enable Use the ip mcast-stub helper-enable comma nd to assign the ip mcast-stub helper-address as the IGMP proxy. Use the no form of this command to disable.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 820 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode. Use the no form of this command to disable.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 821 ip osp f Use the ip ospf command to customize O SPF settings (if needed). Synt ax Description authentication-key S pecifies a simple-text authen tication password to be used by other routers using <password> the OSPF simple password authentic at ion .
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 822 Usage Example The following exam ple s ets the maximu m nu m ber of seco nd s allo we d be twe en he llo packets t.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 823 ip ospf authentication [ message-digest | null ] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication. Synt ax Description message-dig est Optional.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 824 ip ospf network [ broa dcast | po int-to-point ] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Set the ne twork type for broadcast.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 825 ip pim sp arse-mode Use the ip pim sparse-mode command to enable protoc ol-independent multicast (PIM) sparse mode for this interface. Use the no form of this command to disable PIM sparse mode.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 826 ip pim-sp arse dr-priority <priority number> Use the ip pim-sparse dr-priority command to specify the priority for the designated router (DR). This command modifies the rout ers priority in the DR election process.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 827 ip pim-sp arse hello-timer <time> Use the ip pim-sparse hello-timer command to specify protocol-indepen dent multicast (PIM) sparse hello timer period. This is the time interval at which periodic hellos are sent out on all interfaces of a PIM-capable router.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 828 ip pim-sp arse nbr-timeout <time> Use the ip pim-sparse nbr-timeout command to specify protocol-ind ependent multicast (PIM) sparse neighbor timeout. This is the time interval after which a P IM-capa ble router will consider a neighbor not present.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 829 ip pim-sp arse override-interval <time> Use the ip pim-sparse over ride-interval command to specify the protoc ol-independent multicast (PIM) sparse join/prune override interval.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 830 ip pim-sp arse pr op agation-delay <time> Use the ip pim-sparse propagation-delay command to specify protoc ol-independent multicast (PIM) sparse join/prune propagation delay.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 831 ip policy route-map <policy name> Use the ip policy route-map command to assign a policy route- map to this interface. Use the no form of this command to remove the route-map policy.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 832 ip proxy-arp <ip address> <s ubnet mask> Use the ip proxy-arp command to enable proxy Address Resolutio n Protocol (ARP) on the interface. Use the no form of this command to disable this feature.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 833 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface. Use the no form of this command to restore the default value.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 834 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface. Use the no form of this command to restore the default value.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 835 ip route-cache Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 836 ip unnumbered <interface> Use the ip unnumbered command to use the IP address assigned to the specified interface for all IP processing on the active interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 837 keep alive <seconds> Use the keepalive command to enable the transmission of keep alive pa ckets on the interface and specify the time interval in seconds between transmitted packets.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 838 lld p receive Use the lldp receive command to allow LLDP packets to be received on this interface. Synt ax Description No subcommands. Default V alues By default, all interfaces are configured to send and receive LLDP packets.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 839 lld p send [management-addre ss l port-description l system-cap abilities l system-description l system-name l and.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 840 Usage Examples The following example configures the HDLC interface to transmit LLDP p ackets co ntaining all enabl.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 841 max-reserved-bandwidth <percent> Use the max-reserve d-bandwidth command to define the maximum amount o f interface bandwidth reserved for Quality of Service (QoS).
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 842 mtu <size> Use the mtu command to configure the ma ximum transmit unit (MTU) size for the active interface. Use the no form of this command to return to the default value.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 843 qos-policy out <mapname> Use the qos-policy out command to apply a previously -configu red QoS map to an interface. Use the no form of this command to remove the map from the interface.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 844 Usage Examples The following example applies th e QoS map VOICEMAP to the HDLC inte rface: (config)# interface hdl.
Command Refere nce Guide HDLC Command Set 61200990L1-35E Copyright © 2005 ADTRAN 845 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Network Management Protocol (SNMP) variable ifLinkUpDownTrapEnable (R FC2863) to en able (or disable) the interface to send SNMP traps when there is an interface status change.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 846 L OOPBACK I NTERFACE C ONFIGURATION C OMMAND S ET To activate the Loopback Interf ace Configuration mode, enter the interface loopback command at the Global Configuration mode prompt .
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 847 access-policy <policyname> Use the access-policy comma nd to assign a specified access policy for the inbound traffi c to an interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 848 Create the access policy that contains the access list InWeb : (config)# ip policy-cl.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 849 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 850 bandwid th <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 851 crypto map <mapname> Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> S pecifies the crypto map name that you wish to assign to the interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 852 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated w ith the inter face on whic h the data is receiv ed.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 853 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 854 If your IP address doesn't c hange often or at all, but you still want an easy name to remember it by (without having to purchase your own domain name) , S tatic DNS service is ideal for you.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 855 ip access-group <listname> [ in | out ] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 856 ip address <address> <mask> secondary Use the ip address command to define an IP address on th e specified interface. Use the optional secondary keyword to define a secondary IP address.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 857 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 858 Usage Examples The following example forwar ds all DNS br oadcast traf fic to the DNS server with IP address 192.33.5.99: (config)# ip forward-protocol ud p domain (config)# interface loopback 1 (config-loop 1)# ip helper-address 192.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 859 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV ant a 300, 1000R, 2000, 3000, 4000, and 5000 and T otal Access 900 Series unit s.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 860 Usage Examples The following example sets the qu ery message interval on the interfac.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 861 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface and place it in multicast stub downstream mode.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 862 ip mcast-stub helper-enable Use the ip mcast-stub helper-enable comma nd to assign the ip mcast-stub helper-address as the IGMP proxy. Use the no form of this command to disable.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 863 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 864 ip osp f Use the ip ospf command to customize O SPF settings (if needed).
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 865 Usage Example The following exam ple s ets the maximu m nu m ber of seco nd s allo we.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 866 ip osp f authentication [message-digest | null] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 867 ip osp f network [broad cast | point-to-point] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Set s the network type for broadcast.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 868 ip pim sp arse-mode Use the ip pim sparse-mode command to enable protoc ol-independent multicast (PIM) sparse mode for this interface. Use the no form of this command to disable PIM sparse mode.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 869 ip pim-sp arse dr-priority <priority number> Use the ip pim-sparse dr-priority command to specify the priority for the designated router (DR).
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 870 ip pim-sp arse hello-timer <time> Use the ip pim-sparse hello-timer command to specify protocol-indepen dent multicast (PIM) sparse hello timer period.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 871 ip pim-sp arse nbr-timeout <time> Use the ip pim-sparse nbr-timeout command to specify protocol-ind ependent multicast (PIM) sparse neighbor timeout.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 872 ip pim-sp arse override-interval <time> Use the ip pim-sparse over ride-interval command to specify the protoc ol-independent multicast (PIM) sparse join/prune override interval.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 873 ip pim-sp arse pr op agation-delay <time> Use the ip pim-sparse propagation-delay command to specify protoc ol-independent multicast (PIM) sparse join/prune propagation delay.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 874 ip policy route-map <policy name> Use the ip policy route-map command to assign a policy route- map to this interface. Use the no form of this command to remove the route-map policy.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 875 ip proxy-arp <address> <subnet mask> Use the ip proxy-arp command to enable proxy Address Resolutio n Protocol (ARP) on the interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 876 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 877 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 878 ip route-cache Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 879 ip unnumbered <interface> Use the ip unnumbered command to use the IP address assigned to the specified interface for all IP processing on the active interface.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 880 mtu <size> Use the mtu command to configure the maximum transmit unit size for the active interface. Use the no form of this command to re turn to the default value.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 881 snmp trap Use the snmp trap command to enable all supported Simple Network Management Proto col (SNMP) traps on the interface. Synt ax Description No subcommands.
Command Refere nce Guide Loopback Interfa ce Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 882 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple N.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 883 PPP I NTERFACE C ONFIGURATION C OMMAND S ET To activate the PPP Interface Configuration mode, enter the interface ppp command at the Global Configuration mode prompt.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 884 max-reserved-bandwidth <percent> on page 949 mtu <size> on page 950 peer defau.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 885 access-policy <policyname> Use the access-policy comma nd to assign a specified access policy for the inbound traffi c to an interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 886 Create the access policy that contains the access list InWeb : (config)# ip policy-class U.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 887 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 888 alias link <“text”> Each configured PPP interface (whe n referenced using SNMP) contains a lin k (physical port) and a bundle (group of links).
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 889 bandwid th <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 890 bridge-group <group#> Use the bridge-group command to assign an interface to the speci fied bridge group. This c ommand is supported on all Ethernet interfaces, PPP virtual in terfaces, and Frame Relay virtual sub-interfaces.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 891 bridge-group <group#> bp dufilter [enable | disable] Use the bridge-group bpdufilter command to block BPDUs from bei ng transmitted and received on this interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 892 bridge-group <group#> bp duguard [enable | disable] Use the bridge-group bpduguard command to block BPDUs from being received on this interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 893 bridge-group <group#> edgeport [disable] Use the bridge-group edgeport command to set this interface to be an edgeport. This configures the interface to go to a forwarding st ate when the link goes up.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 894 bridge-group <group#> link-type [auto | point-to-point | shared] Use the bridge-group link-type command to configure the sp anning-tree protocol link ty pe for an interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 895 bridge-group <group#> sp anning-disabled Use the bridge-group spanning-disabled comm.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 896 crypto map <mapname> Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> Assigns a crypto m ap name t o the inter face.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 897 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated w ith the inter face on whic h the data is receiv ed.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 898 dial-backup auto-backup Use the dial-backup auto-backup command to configure the PPP inte rface to automatically attempt a dial-backup upon failure.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 899 dial-backup auto-restore Use the dial-backup auto-restore command to configure the interface to automatically discontinue dial-backup when all network cond itions are operational.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 900 dial-backup backup-delay <seconds> Use the dial-backup backup-delay command to configure the amount of time the router will wait after t he failure condition is recogniz ed before attempting to backup the link.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 901 dial-backup call-mode [answer | answer-always | originate | originate-answer | or iginate-.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 902 interface t1 1/1 coding b8zs framing esf clock source line tdm-g roup 1 timeslots 1-24 speed 64 no shutdown ! interface ppp 1 description Prim ar y Int erfa c e for Co nn ec tio n to Cent ra l 3200 ip address 10.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 903 no shutdown ! interface t1 1/1 coding b8zs framing esf clock source internal tdm-g roup 1 .
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 904 T echnology Review This technology review provides information regardin g sp ecific dial-backup router beh avior (i.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 905 dial-backup connect-timeout <seconds> Use the dial-backup connect-timeout command to specify the number of se conds to wait for a connection after a call is attempted before trying to call again or dialing a different number .
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 906 dial-backup force [backup | primary] Use the dial-backup force command to manually overri de the automatic dia l-ba c ku p feature.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 907 dial-backup maximum-retry <attempts> Use the dial-backup maximum-retry command to select the number of ca lls the rout er w ill make when attempting to backup a link.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 908 dial-backup number <digit s> [analog | digit al-56k | digital 64k] <isdn min chan.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 909 dial-backup priority <value> Use the dial-backup priority command to select the backup priority for this interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 910 dial-backup randomize-timers Use the dial-backup randomize-timers command to randomize the call ti mers to minimize potential contention for resources.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 911 dial-backup redial-delay <seconds> Use the dial-backup redia l-delay command to configure the delay afte r an unsuccessful call until the call will be re-tried.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 912 dial-backup restore-delay <seconds> Use the dial-backup restore-delay command to configure the amount of time the router will wait after the network is restored before disconnecting the backup lin k and reverting to the primary.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 913 dial-backup schedule [day | enable-time | disable-time] Use the dial-backup schedule command to set the time of day that backup will be enabled.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 914 dial-backup shut down Use the dial-backup shutdown command to deactivate all dial-b ackup functionality in the unit.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 915 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 916 dyndns-st atic - The S tatic DNS service is similar to Dynamic DNS service, in that it allows a hostname such as yourname.dyn dns.org to point to your IP a ddress.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 917 fair-queue <threshold> Use the fair-queue command to enable weighted fair qu euing (WFQ) on an interface. Use the no for m of this command to disable WFQ and en able FIFO queueing for an interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 918 hold-queue <queue size> out Use the hold-queue out command to change the overall size of an interfa ce's WAN output queue.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 919 ip access-group <listname> [in | out] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 920 ip address dhcp Use the ip address dhcp command to use Dynamic Ho st Configuration Protocol (DHCP) to obtain an address on the interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 921 ip address negotiated [no-default] Use the ip address negotiated command to allow the interface to ne gotiate (i.e., be assigned) an IP address from the far end PPP connection.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 922 ip address <address> <mask> secondary Use the ip address command to define an IP address on the sp ecified interface. Use the optional keyword secondary to define a secondary IP address .
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 923 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 924 Usage Examples The following example forwar ds all DNS br oadcast traf fic to the DNS server with IP address 192.33.5.99: (config)# ip forward-protocol ud p domain (config)# interface ppp 1 (config-ppp 1)# ip helper -address 192.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 925 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV anta 300, 1000R, 20 00, 3000, 4000, 5000 and T otal Access 900 Ser ies units.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 926 Command History Release 7.1 Command was introdu ced.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 927 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface and place it in multicast stub downstream mode.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 928 ip mcast-stub helper-enable Use the ip mcast-stub helper-enable comma nd to assign the ip mcast-stub helper-address as the IGMP proxy. Use the no form of this command to disable.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 929 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 930 ip osp f Use the ip ospf command to customize O SPF settings (if needed). Applicable Plat forms This command applies to the NetV ant a 300, 1000R, 2000, 3000, 4000, and 5000 and T otal Access 900 Series units.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 931 ip osp f authentication [message-digest | null] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 932 ip osp f network [broad cast | point-to-point] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Set s the network type for broadcast.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 933 ip pim sp arse-mode Use the ip pim sparse-mode command to enable protoc ol-independent multicast (PIM) sparse mode for this interface. Use the no form of this command to disable PIM sparse mode.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 934 ip pim-sp arse dr-priority <priority number> Use the ip pim-sparse dr-priority command to specify the priority for the designated router (DR).
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 935 ip pim-sp arse hello-timer <time> Use the ip pim-sparse hello-timer command to specify protocol-indepen dent multicast (PIM) sparse hello timer period.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 936 ip pim-sp arse nbr-timeout <time> Use the ip pim-sparse nbr-timeout command to specify protocol-ind ependent multicast (PIM) sparse neighbor timeout.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 937 ip pim-sp arse override-interval <time> Use the ip pim-sparse over ride-interval command to specify the protoc ol-independent multicast (PIM) sparse join/prune override interval.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 938 ip pim-sp arse pr op agation-delay <time> Use the ip pim-sparse propagation-delay command to specify protoc ol-independent multicast (PIM) sparse join/prune propagation delay.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 939 ip policy route-map <policy name> Use the ip policy route-map command to assign a policy route- map to this interface. Use the no form of this command to remove the route-map policy.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 940 ip proxy-arp <address> <s ubnet mask> Use the ip proxy-arp to enable proxy Address Resolution Protocol (ARP) on th e interface. Use the no form of this command to disable this feature.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 941 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 942 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 943 ip route-cache Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 944 ip unnumbered <interface> Use the ip unnumbered command to use the IP address assigned to the specified interface for all IP processing on the active interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 945 keep alive <seconds> Use the keepalive command to enable the transmission of keep alive pa ckets on the interface and specify the time interval in seconds between transmitted packets.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 946 lld p receive Use the lldp receive command to allow LLDP packets to be received on this interface. Synt ax Description No subcommands. Default V alues By default, all interfaces are configured to send and receive LLDP packets.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 947 lld p send [management-addre ss l port-description l system-cap abilities l system-descrip.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 948 Usage Examples The following example configures t he PPP interface to transmit LLDP p acke.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 949 max-reserved-bandwidth <percent> Use the max-reserve d-bandwidth command to define the maximum amount o f interface bandwidth reserved for Quality of Service (QoS).
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 950 mtu <size> Use the mtu command to configure the ma ximum transmit unit (MTU) size for the active interface. Use the no form of this command to return to the default value.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 951 peer default ip address <address> Use the peer default ip address command to specify the default IP address of the remote end of this interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 952 ppp authentication [chap | p ap] Use the ppp authentication command to specify the authentication protocol on the PPP virtual interface that the peer should use to authenticate itself.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 953 Several examp le sce na r ios ar e giv en below fo r c lar ity . Configuring P AP Example 1: Only the local rout er requires the pee r to authenticate it self.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 954 Several examp le sce na r ios ar e giv en below fo r c lar ity . Configuring CHAP Example 1: On ly the local router requires th e peer to authenticate it self.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 955 Configuring CHAP Example 3: Both routers require ea ch other to authenticate thems elves using the same shared p assword.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 956 Configuring CHAP Example 5: Using the ppp chap hos tna me command as an alternate solution.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 957 ppp chap hostname <hostname> Use the ppp chap hostname command to configure an alternate hostname for CHAP PPP authentication. Use the no form of this command to remove a configur ed hostname.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 958 ppp chap p assword <password> Use the ppp chap password command to configure an alternate p assword when the peer requires CHAP PPP authentication.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 959 ppp multilink [fragment ation | interleave] Use the ppp multilink command to enable multilink PPP (MPPP) operation om an existing PPP interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 960 ppp p ap sent-username <username> pa ssword <password> Use the ppp pap sent-username/password command to configure a username and password when the peer requires PAP PPP authentication.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 961 pppoe ac-name <name> Use the pppoe ac-name command to identify the Access Concentr ator (AC) w ith which the AOS e xpects to establish a PPPoE session.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 962 pppoe service-name <name> Use the pppoe service-name command to use this tag value to filter PPPoE session offers from PPPoE servers. Use the no form of this command to re turn to the default setting.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 963 qos-policy out <mapname> Use the qos-policy out command to apply a previously -configu red QoS map to an interface. Use the no form of this command to remove th e map from the interface.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 964 Usage Examples The following example applies th e QoS map VOICEMAP to the PPP 1 interface:.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 965 snmp trap link-st atus Use the snmp trap link-status command to control th e Simple Networ.
Command Refere nce Guide PPP Interface Config uration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 966 username <username> password <p assword> Configures the username an d password of the peer to use for PPP authentication.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 967 T UNNEL C ONFIGURATION C OMMAND S ET To activate the Tunnel C onfiguration mod e, enter the interface tunnel command at the Global Configuration mode prompt.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 968 access-policy <policyname> Use the access-policy command to assign a specified access policy for the inbound tra ffic on an interface. Use the no form of this command to remove an access policy association.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 969 Create the access policy that contains the access list InWeb : (config)# ip policy-class UnT rust.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 970 discard list <access list names> policy <access policy name> All packet s passed by the access list(s) entered and destined for the interface u sin g the access policy listed will be blocked from the router sy stem.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 971 bandwid th <value> Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols. This value is used in cost calculations.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 972 crypto map <mapname> Use the crypto map command to associate crypto maps with the interface. Synt ax Description <mapname> Assigns a crypto m ap name t o the inter face.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 973 As shown in the diagram above, data coming into th e product is fir st process ed by the s tatic filter associated w ith the inter face on whic h the data is receiv ed.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 974 dial-backup auto-backup Use the dial-backup auto-backup command to configure the PPP inte rface to automatically attempt a dial-backup upon failure.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 975 dial-backup auto-restore Use the dial-backup auto-restore command to configure the interface to automatically discontinue dial-backup when all network cond itions are operational.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 976 dial-backup backup-delay <seconds> Use the dial-backup backup-delay command to configure the amount of time the router will wait after t he failure condition is recogniz ed before attempting to backup the link.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 977 dial-backup call-mode [answer | answer-always | originate | originate-answer | or iginate-answer-.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 978 interface t1 1/1 coding b8zs framing esf clock source line tdm-g roup 1 timeslots 1-24 no shutdown ! interface ppp 1 ip address 10.1.1.2 25 5.255.255.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 979 no shutdown cross-conn ect 1 t1 1/1 1 p pp 1 ip address 10.1.1.1 25 5.255.255.252 dial-backup call-mode answer dial-backup number 5 55-8888 analog ppp 2 ! interface ppp 2 description connection fo r remote 3200 dialin for backup ip address 10.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 980 dial-backup connect-timeout <seconds> Use the dial-backup connect-timeout command to specify the number of se conds to wait for a connection after a call is attempted before trying to call again or dialing a different number .
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 981 dial-backup force [backup | primary] Use the dial-backup force command to manually overri de the automatic dia l-ba c ku p feature.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 982 dial-backup maximum-retry <attempts> Use the dial-backup maximum-retry command to select the number of ca lls the rout er w ill make when attempting to backup a link.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 983 dial-backup number <digit s> [analog | digit al-56k | digital 64k] <isdn min chan> &l.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 984 dial-backup priority <value> Use the dial-backup priority command to select the backup priority for this interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 985 dial-backup randomize-timers Use the dial-backup randomize-timers command to randomize the call ti mers to minimize potential contention for resources.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 986 dial-backup redial-delay <seconds> Use the dial-backup redia l-delay command to configure the delay afte r an unsuccessful call until the call will be re-tried.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 987 dial-backup restore-delay <seconds> Use the dial-backup restore-delay command to configure the amount of time the router will wait after the network is restored before disconnecting the backup lin k and reverting to the primary.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 988 dial-backup schedule [day | enable-time | disable-time] Use the dial-backup schedule command to set the time of day that backup will be enabled.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 989 dial-backup shut down Use the dial-backup shutdown command to deactivate all dial-b ackup functionality in the unit.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 990 dynamic-dns [dyndns | dynd ns-custom | dyndns-st atic] <hostname> <username> <password> Use the dynamic-dns command to configure Dynamic DNS ser vice provided by Dynamic Network Services, Inc.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 991 dyndns-st atic - The S tatic DNS service is similar to Dynamic DN S service in that it a llows a host name such as yourname.dyndn s.or g to po int to your IP a ddr ess.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 992 ip access-group <listname> [in | out] Use the ip access-group command to create an access list to be used for packets transmitted on or received from the specified interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 993 ip address <address> <mask> secondary Use the ip address command to define an IP address on the specified interface. Use the no form of this command to remove a configured IP address.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 994 ip helper-address <address> Use the ip helper-address command to configure the AOS to fo rward User Datagram Protocol (UDP) broadcast packets received on the interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 995 Usage Examples The following example forwar ds all DNS br oadcast traf fic to the DNS server with IP address 192.33.5.99: (config)# ip forward-protocol ud p domain (config)# interface tunnel 1 (config-tunnel 1)# ip helper-a ddress 192.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 996 ip igmp Use the ip igmp command to configure multic asting-re lated functions for the interface. Applicable Plat forms This command applies to the NetV ant a 300, 1000R, 2000, 3000, 4000, and 5000 and T otal Access 900 Series units.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 997 Command History Release 7.1 Command was introdu ced.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 998 ip mcast-stub downstream Use the ip mcast-stub downstream command to ena ble multicast forwar ding and IGMP (router mode) on an interface, and to place it in multi cast stub downstream mode.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 999 ip mcast-stub helper-enable Use the ip mcast-stub helper-enable comma nd to assign the ip mcast-stub helper-address as the IGMP proxy. Use the no form of this command to disable.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1000 ip mcast-stub up stream Use the ip mcast-stub upstream command to enable multicast forwardi ng on an interface and place it in multicast stub upstream mode.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1001 ip osp f Use the ip ospf command to customize O SPF settings (if needed).
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1002 Usage Example The following exam ple s ets the maximu m nu m ber of seco nd s allo we d be twe e.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1003 ip osp f authentication [message-digest | null] Use the ip ospf authentication command to authenticate an inte rface that is performing OSPF authentication.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1004 ip osp f network [broad cast | point-to-point] Use the ip ospf network command to specify the type of network on this interface. Synt ax Description broadcast Sets the network type for broadcast.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1005 ip pim sp arse-mode Use the ip pim sparse-mode command to enable protoc ol-independent multicast (PIM) sparse mode for this interface. Use the no form of this command to disable PIM sparse mode.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1006 ip pim-sp arse dr-priority <priority number> Use the ip pim-sparse dr-priority command to specify the priority for the designated router (DR).
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1007 ip pim-sp arse hello-timer <time> Use the ip pim-sparse hello-timer command to specify protocol-indepen dent multicast (PIM) sparse hello timer period.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1008 ip pim-sp arse nbr-timeout <time> Use the ip pim-sparse nbr-timeout command to specify protocol-ind ependent multicast (PIM) sparse neighbor timeout.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1009 ip pim-sp arse override-interval <time> Use the ip pim-sparse over ride-interval command to specify the protoc ol-independent multicast (PIM) sparse join/prune override interval.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1010 ip pim-sp arse pr op agation-delay <time> Use the ip pim-sparse propagation-delay command to specify protoc ol-independent multicast (PIM) sparse join/prune propagation delay.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1011 ip policy route-map <policy name> Use the ip policy route-map command to assign a policy route- map to this interface. Use the no form of this command to remove the route-map policy.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1012 ip proxy-arp <ip address> <s ubnet mask> Use the ip proxy-arp command to enable proxy Address Resolutio n Protocol (ARP) on the interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1013 ip rip receive version [1 | 2] Use the ip rip receive version command to config ure the RIP versio n the unit accepts in all RIP packets received on the interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1014 ip rip send version [1 | 2] Use the ip rip send version comma nd to configure the RIP versi on the unit sends in all RIP packets transmitted on the interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1015 ip route-cache Use the ip route-cache command to enable fast-cache switching on the interface. Use the no form of this command to disable fast-cach e switching and return to process switching mode.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1016 keep alive <period> <retries> Use the keepalive command to periodically send keepalive pa ckets to verify the integrity of the tunnel from end to end.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1017 lld p receive Use the lldp receive command to allow LLDP packets to be received on this interface. Synt ax Description No subcommands. Default V alues By default, all interfaces are configured to send and receive LLDP packets.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1018 lld p send [management-addre ss l port-description l system-cap abilities l system-description l.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1019 Usage Examples The following example configure s the tunnel interfac e to transmit LL DP p acket.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1020 mtu <size> Use the mtu command to configure the ma ximum transmit unit (MTU) size for the active interface. Use the no form of this command to re turn to the default value.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1021 tunnel checksum Use the tunnel checksum command to verify the ch ecksum of incoming Gene ric Routing Encapsulation (GRE) packets and to include a checks um on outgoing pa ckets.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1022 tunnel destination <ip address> Use the tunnel destination command to specify the IP address to use as the destination address for all packets transmitted on this interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1023 tunnel key <value> Use the tunnel key command to specify a value sh ared by both endpoints of the tunnel that will provide minimal security and delineate between tunnels with the same source a nd destination addresses.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1024 tunnel mode gre Use the tunnel mode gre command to encapsula t e traffi c de sti ned for the tunnel interface in a Generic Routing Encapsulation (GRE) header.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1025 tunnel sequence-dat agrams Use the tunnel sequence-datagrams command to enable seq uence number .
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1026 tunnel source [ <ip address> | <interface> ] Use the tunnel source command to specify the IP address or name of a physic al interface to use as the source address for all packets transmitted on this interface.
Command Refere nce Guide Tunnel Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1027 Usage Examples The following e xample sets the tu nnel source IP address to 192.22.73.101 : (config)# interface tunnel 1 (config-tunnel 1)# tunne l source 192.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1028 CA P ROFILE C ONFIGURATION C OMMAND S ET To activate the Certificate Authority (C A) Profile Configuration mode, enter the crypto ca profile command at the Global Co nfiguration mode prompt.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1029 crl optional Use the crl optional command to make CRL verification optional. Synt ax Description No subcommands. Default V alues By default, CRL optional is enabled.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1030 email address <email address> Use the email address command to specify that an email address should be included in the certificate request.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1031 enrollment retry [count | period] Use the enrollment retry command to determine how the AO S handles certificate requests.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1032 enrollment terminal Use the enrollment terminal command to specify manual (i.e., cut-and-paste) certificate enrollment. Synt ax Description No subcommands.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1033 enrollment url <url> Use the enrollment url command to specify the URL of the CA to which the AOS shou ld send certificate requests. Synt ax Description <url> S pecifies the certificate authority’ s URL (e.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1034 fqdn <fqdn> Use the fqdn command to specify a fully-qualif ied domain name (FQDN) to be included in the certificate requests. Synt ax Description <fqdn> S pecifies the FQDN (e.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1035 ip-address <address> Use the ip-address comma nd to specify an IP address to be included in the certificate requests. Synt ax Description <address> Defines the IP address in dotted decimal not ation (e.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1036 p assword <p assword> Use the password command to specify the challenge password fo r simple certificate exchange protocol (SCEP).
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1037 serial-number Use the serial-number command to specify that a serial number w ill be included in the certificate request. Synt ax Description No subcommands.
Command Refere nce Guide CA Profile Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1038 subject-name <name> Use the subject-name command to specify the subject name used in the certificate request. Synt ax Description <name> S pecifies a su bject name string using up to 256 characters entered in X.
Command Refere nce Guide Certificate Config urat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1039 C ERTIFICATE C ONFIGURATION C OMMAND S ET To activate the Certificate Configuration mode, enter the crypto ca c ertificate chain command at the Global Configuration mode prompt .
Command Refere nce Guide Certificate Config urat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1040 certificate <serial-number> Use the certificate command to restore a certificate. Use the no form of this command to remove a specific certificate from the certificate chain.
Command Refere nce Guide Certificate Config urat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1041 certificate ca <serial-number> Use the certificate ca command to restore a CA certificate. Use the no form of this command to remove a specific certificate from the certificate chain for a CA.
Command Refere nce Guide Certificate Config urat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1042 crl Use the crl command to restore a CRL. Use the no form of this command to remove the CRL for the specific CA. Synt ax Description No subcommands.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1043 C RYPTO M AP IKE C OMMAND S ET To activate the Crypto Map IKE m ode, enter a valid version of the crypto map ipsec-ike command at the Global Configuration mode prompt .
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1044 antireplay Use the antireplay command to enable antireplay sequence number checking for all security associations created on this crypto map. Use the no form of this command to disable.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1045 ike-policy <policy number> Use the ike-policy command to ensure that only a specified IKE policy is used to establish the IPSec tunnel.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1046 match address <listname> Use the match address command to assign an IP access list to a crypto map definition. The access list designates the IP packet s to be encr ypted by this crypto map.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1047 Usage Examples The following example shows setting up an ACL (called NewList ) and then assigning the n.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1048 set peer <address> Use the set peer command to set the IP address of the peer de vice. This must be set for multiple remote peers. Synt ax Description <address> S pecifies the IP addr ess of the peer device.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1049 set p fs [group1 | group2] Use the set pfs command to choose the type of perfect forward sec recy (if any) that w ill be required during IPSec negotiation of security associatio ns for this crypto map.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1050 set security-association lifet ime [kilobytes | seconds] <value> Use the set security-association lifetime command to define the lifetime (i n kilobytes and/or seconds) of the IPSec SAs create d by this crypto map.
Command Refere nce Guide Crypto Map IKE Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1051 set transform-set <setname1 - setname6> Use the set transform-set command to assign up to six transfor m sets to a crypto map.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1052 C RYPTO M AP M ANUAL C OMMAND S ET To activate the Crypto Map Manual mode, enter a valid version of the crypto map ipsec-manual command at the Global Co nfiguration mode prompt.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1053 antireplay Use the antireplay command to enable antireplay sequence number checking for all security associations created on this crypto map. Use the no form of this command to disable.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1054 ike-policy <policy number> Use the ike-policy command to ensure that only a specified IKE policy is used to establish the IPSec tunnel.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1055 match address <listname> Use the match address command to assign an IP access list to a crypto map definition. The access list designate s the IP packet s to be encrypted by this crypto m ap.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1056 Usage Examples The following example s hows setting u p an access lis t (called NewList ) and then a.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1057 set peer <address> Use the set peer command to set the IP address of the peer device. Synt ax Description <address> S pec ifies the IP address of the peer d evice.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1058 set session-key [inb ound | outbound] Use the set session-key command to define the encr yption and authentication keys for this crypto map.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1059 Functional Notes The inbound local security parameter index (SPI) must equal the outbound remote SPI. The outbound local SPI must equal the inbound remote SPI.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1060 St e p 4 : Define an IP access list. An Extended Access Control List is used to specify which traffic needs to be sent securely over the VPN tunnel. The entries in the list a r e defined with respect to the local system.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1061 St e p 6 : Configure public interface. This process includes conf iguring the IP address for the interface and applying the appropriate crypto map to the interface.
Command Refere nce Guide Crypto Map Manual Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1062 set transform-set <setname> Use the set transform-set command to assign a tra nsform set to a crypto map. See crypto ipsec transform-set <setname> <parameters> on page 329 for information on defining transfor m sets.
Command Refere nce Guide IKE Client Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1063 IKE C LIENT C OMMAND S ET To activate the IKE Client mode, enter the crypto ike client command at the Global Configuration mode prompt.
Command Refere nce Guide IKE Client Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1064 dns-server <address1> <address2> Use the dns-ser ver command to specify the DNS server address(es) to assign to a client. Synt ax Description <address1> Assigns the first DNS server address.
Command Refere nce Guide IKE Client Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1065 ip-range <start ip> <end ip> Use the ip-range command to specify the range of addresses from which the router dra ws when assigning an IP address to a client.
Command Refere nce Guide IKE Client Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1066 netbios-name-server <address1> <address2> Use the netbios-name-server command to specify the NetBIOS Wi ndows Internet Naming Service (WINS) name servers to assign to a client.
Command Refere nce Guide IKE Policy Attrib utes Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1067 IKE P OLICY A TTRIBUTES C OMMAND S ET To activate the IKE Policy Attributes mode, enter the attribute command at the IKE Policy prompt.
Command Refere nce Guide IKE Policy Attrib utes Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1068 authentication [dss-sig | pre-share | rsa-sig] Use the authentication command to configure this IKE policy’s use of pre-shared secrets and s igned certificates during IKE negotiation.
Command Refere nce Guide IKE Policy Attrib utes Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1069 encryption [aes-xxx-c bc | des | 3des] Use the encryption command to specify which encryption algorithm this IKE policy will use to transmit data over the IKE-generated SA.
Command Refere nce Guide IKE Policy Attrib utes Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1070 group [1 | 2] Use the group command to specify the Diffie-Hellman Group (1 or 2) to be used by this IKE policy to generate the keys (which a re then used to create the IP Sec SA).
Command Refere nce Guide IKE Policy Attrib utes Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1071 hash [md5| sha] Use the hash command to specify the hash algorithm to be us ed to authenticate the data transmitted over the IKE SA. Synt ax Description md5 Choose the MD5 hash algo rithm.
Command Refere nce Guide IKE Policy Attrib utes Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1072 lifetime <seconds> Use the lifetime command to s pecify how long an IK E SA is valid before expiring. Synt ax Description <seconds> S pecify how many seconds an IKE SA will last before expiring.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1073 IKE P OLICY C OMMAND S ET To activate the IKE Po licy mode, enter the crypto ike policy command at the Global Configuration mode prompt.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1074 attribute <policynumber> Use the attribute command to define attributes for the associat ed IKE policy. Multiple attributes can be created for a single IKE policy.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1075 client authentication host Use the client authentication host command to enable the unit to act as an Xauth host when this IKE policy is negotiated with a peer.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1076 client authentication host xaut h-type [generic | otp | radius] Use the client authentication host xauth-type command to allow the user to specify the Xauth authentication type if a type other than generic is desired.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1077 client authentication server list <listname> Use the client authentication server lis t command to enable the unit to act as an Xauth server (edge device).
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1078 client configuration pool <poolname> Use the client configuration pool command to configure the AOS to perform as mode-config server (edge device) when an IKE policy is ne gotiated.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1079 initiate [main | aggressive] Use the initiate command to allow the IKE po licy to initiate negotiation (i n main mode or aggressive mode) with peers. Use the no form of this command to a llow the policy to respond only.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1080 local-id [address | asn1-dn | fqdn | use r-fqdn] <ip address or name> Use the local-id command to set the local ID for the IKE policy.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1081 Usage Examples The following example sets the local ID of this IKE policy to the IP v4 address 63.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1082 nat-traversal <version> [allow | disable | force] Use the nat-traversal command to allow, force, or disable NA T tr aversal version 1 and 2 on a specific Ike policy.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1083 peer [ <ip address> | any] Use the peer command to enter the IP address of the peer de vice. Repeat this comm and for multiple peers. Use the any keyword if yo u want to set up a policy th at will initiate or respond to any peer.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1084 The following example set s up a policy allowing any peer to initiate using preshared secret, DES, MD5, and Diffie-Hellma n Group 1.
Command Refere nce Guide IKE Policy Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1085 respond [main | aggressive | anymode] Use the respond command to allow the IKE policy to resp ond to negotiations by a peer. Use the no form of this command to allow the polic y to only initiate negotiations.
Command Refere nce Guide AS Path List Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1086 AS P ATH L IST C OMMAND S ET To activate the Autonomo us System (AS) Path List Configuration mode, enter the ip as-path-list command at the Global Co nfiguration mode prompt.
Command Refere nce Guide AS Path List Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1087 deny Use the deny command to deny a BG P route that matches the as-path attributes. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide AS Path List Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1088 permit Use the permit command to allow a BGP route tha t matches the as-path attributes. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide BGP Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1089 BGP C ONFIGURATION C OMMAND S ET To activate the BGP Conf iguration mode, enter the router bgp command at the Global Configuration mode prompt.
Command Refere nce Guide BGP Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1090 bgp fast-external-fallover Use the bgp fast-external-fallover command to enable the fast-external-fallover fea ture. Synt ax Description No subcommands.
Command Refere nce Guide BGP Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1091 bgp log-neighbor-changes Use the bgp log-neighbor-changes command to control the logging of neighbor state change s. Use the no form of this command to re turn to the default setting.
Command Refere nce Guide BGP Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1092 bgp router-id <ip address> Use the bgp router-id command to specify the IP address that the router should u se as its BGP router ID. Use the no form of this command to return to the default setting.
Command Refere nce Guide BGP Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1093 dist ance bgp <external> <internal> <local> Use the distance bgp command to set the administrative dist anc e for BGP routes. Use the no form of this command to return to the default setting.
Command Refere nce Guide BGP Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1094 hold-timer <hold time> Use the hold-timer command to set the default hold time for all ne ighbors in the BGP process .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1095 BGP N EIGHBOR C ONFIGURATI ON C OMMAND S ET To activate the BGP Neighbor Configuration mode, enter the router bgp-neighbor command at the Global Configuration mode prompt .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1096 access-list <listname> [in | out] Use the access-list command to assign a predefined acce ss list to a BGP neighbor . This list is then used to filter inbound and/o r outbound BGP route updates.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1097 advertisement-interval <seconds> Use the advertisement-interval c ommand to configure the AOS to specify how long the BGP process waits before sending updates to the neighb or.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1098 as-p ath-list <listname> [in | out] Use the as-path-list command to assign a predefined autonomous system (AS) path list to a BGP neighbor .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1099 ebgp-multihop <hop count> Use the ebgp-multihop command to configure the maximum ho p count of BGP messages to a neighbor. Use the no form of this command to return to the default setting.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1100 hold-timer <hold time> Use the hold-timer command to set the default hold time for all ne ighbors in the BGP process .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1101 local-as <as-number> Use the local-as command to specify an autonom ous system (AS) number for the unit to use when commu- nicating with this BGP neighbor .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1102 In this network: • Router A is in AS 100. • Router B is in AS 300. • Rou ter A is an eBGP peer with Ro uter B. • Router A’s connection to Router B specifies a local-as of 200.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1103 next-hop-self Use the next-hop-self command to force the next hop attribute to be changed to this unit’s address when advertising networks that wo uld not have the nex t hop changed under normal rules.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1104 p assword <p assword> Use the password command to enable MD5 password authentication on TCP . Use the no form of this command to disable authentication.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1105 prefix-list <listname> [in | out] Use the prefix-list command to assign a predefined prefix list to a BGP neighbor . The list is then used to filter BGP route updates received and/or sent from/by the specified peer .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1106 remote-as <as-number> Use the r emote-as command to specify the BGP au tonomous system (AS) to which the neighbor belongs, adding an entry to the BGP neighbor table.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1107 route-map <map-name> [in | out] Use the ro ut e -m a p command to assign a route ma p to this BGP neighbor . The route map is then used to filter or modify inbo und and/or ou tbound BGP route upda tes.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1108 send-community st andard Use the send-community standard command to insert a standard BGP community attribute to all outgoing route up dates for this neig h bor.
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1109 sof t-reconfiguration inbound Use the soft-reconfigura tion inbound command to enable this unit to st ore BGP updates for the specified neighbor .
Command Refere nce Guide BGP Neighbor Configurat ion Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1110 up date-source <interface> Use the update-source command to specify which virtual interface’ s IP address will be used as the source IP address for the BGP TCP conne ction (whe n connecting to this peer).
Command Refere nce Guide Community List Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1111 C OMMUNITY L IST C OMMAND S ET To activate the Community List Co nfiguration mode, ente r the ip community-list command at the Gl obal Configuration mode prompt.
Command Refere nce Guide Community List Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1112 deny Use the deny command to deny a BGP route th at matches the community number . Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Community List Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1113 permit Use the permit command to allow a BGP route tha t matches the community numbers. Synt ax Description No subcommands. Default V alues No default value necessary fo r this command.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1114 R OUTER (OSPF) C ONFIGURATION C OMMAND S ET To activate the Router (OSPF) Configuration mode, enter the router ospf command at the Global Configuration mode prompt.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1115 area <area id> default-cost <value> Use the area default-cost comma nd to assign a cost of the default summary route sent into a stub area or not-so-stubby-area (NSSA).
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1116 area <area id> range <ip address> <network mask> [advertise | not-advertise] Use the area range command to configure area route summariza tions and to determine whether an addre ss range is advertised to the networks.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1117 area <area id> stub [no-summary] Use the area s tub command to configure an area as a stub area. Use the no form of this command to disable stub-design ation for areas defined as stubs using this command.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1118 auto-cost reference-bandwid th <rate> Use the auto-cost reference-bandwidth command to as sign a different in terface cost to an interface.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1119 default-information-origi nate [always | metric <value> | metric-type <type> ] Use the default-information-originate command to cause an ASBR to gene rate a default route.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1120 default-metric <value> Use the default-metric command to set a metric value for redistributed routes. Synt ax Description <value> Sets the de fa ult metric value (range: 0 to 4,294,967,295).
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1121 maximum p aths <number> Use the maximum paths command to set the maximum number of multipath routes to advertise to the route table via OSPF.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1122 network <ip address> <wildcard> area <area id> Use the network area command to enable routing on an IP stack and to define area IDs for the interfaces on which OSPF will run.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1123 redistribute connected [m etric <value> | metric-type <type> | subnet s] Use the redistribute connected command to advertise routes from one pr otocol to another.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1124 redistribute rip [metric <value> | metric-type <type> | subnet s] Use the redistribute rip command to advertise routes from one protocol to another, regardless of the routing protocol implement ed on the routing domain.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1125 redistribute st atic [metric <value> | metric-type <type> | subnet s] Use the redistribute static command to advertise routes from one protocol to anoth er.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1126 summary-address <address> <mask | prefix mask> not-advertise Use the summary-address command to control addres s summarization of routes that are redistributed into OSPF from other sources (e.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1127 timers lsa-group-p acing <seconds> Use the timers lsa-group-pacing command to change the link state a dvertisement (LSA) refresh interval.
Command Refere nce Guide Router (OSPF) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1128 timers sp f <delay> <hold> Use the timers spf command to configure the shortest path fi rst (SPF) calculation and hold intervals.
Command Refere nce Guide Router (PIM Sparse) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1129 R OUTER (PIM S PA R S E ) C ONFIGURATION C OMMAND S ET To activate the Router (PIM Spar se) Configuration mode, enter th e router pim-sparse command at the Global Configuration mode prompt .
Command Refere nce Guide Router (PIM Sparse) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1130 join-prune-msg-interval <seconds> Use the join-prune-msg-interval command to set a timing rate for PIM sparse join/prune messages.
Command Refere nce Guide Router (PIM Sparse) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1131 rp-address <ip address> access-group <access-list-name> Use the rp-address command to spec ify a static IP addres s fo r the rendezvous point (RP) router.
Command Refere nce Guide Router (PIM Sparse) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1132 Usage Examples The following example specifies an IP addr ess of 172.22.5.100 for th e RP: (config)# router pim-spa rse (config-pim-sparse) # rp-address 172.
Command Refere nce Guide Router (PIM Sparse) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1133 spt-threshold <p ackets> infinity Use the spt-threshold command to change th e.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1134 R OUTER (RIP) C ONFIGURATION C OMMAND S ET To activate the Router (RIP) Configuration mode, enter the router rip command at the Global Configuration mode prompt.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1135 auto-summary Use the auto-summary command to have RIP version 2 su mmari ze subnets to the classful boundaries. Use the no form of this command to disable this summarization.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1136 default-metric <value> Use the default-metric command to set the default metric valu e for the RIP routin g protocol. Use the no form of this command to re turn to the default settings.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1137 network <address> <subnet mask> Use the network command to enable RIP on the specified network.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1138 p assive-interface <interface> Use the passive-interfac e command to disable the transmission of routing upda tes on the specified interface.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1139 redistribute connected [m etric <value> ] Use the redistribute connected c om mand to pass routes from one ne twork to another, regardless of the routing protocol implemen ted on the routing domain.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1140 redistribute osp f [metric <value> ] Use the redistribute ospf command to advertis e routes from one protocol to another, regardless of the routing protocol implemen ted on the routing domain.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1141 redistribute st atic [metric <value> ] Use the redistribute static command to pass routes from one network to another, regardless of the routing protocol implemente d on the routing domain.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1142 timeout-timer <seconds> Use the timeout-timer command to set the timeout timer value for a route when it is learned via RIP. Each time a RIP update for that route is received, the timeout timer is reset to this value.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1143 up date-timer <seconds> Use the update-timer command to set the value of the RIP update interval timer. The RIP update interval is the number of seconds which must elapse betw een RIP update packet transmissions.
Command Refere nce Guide Router (RIP) Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1144 version [1 | 2] Use the version command to specify (globally) the Routing Information Protocol (RIP) version used on all IP interfaces.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1145 DHCP P OOL C OMMAND S ET To activate the DHCP Pool mode, enter the ip dhcp-server pool command at the Global Configuration mode prompt.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1146 client-identifier <identifier> Use the client-identifier command to specify a uniq ue identifier (in dotted hexadecimal notat ion) for a Dynamic Host Configuration Protocol (DHCP) client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1147 The Q.922 ADDRESS field is po pulated using the following: Where the FECN, BECN, C/R, DE, and high order EA bits are assumed to be 0, and the lower order extended address (EA) bit is set to 1.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1148 client-name <name> Use the client-name command to sp ec ify the name of a Dynamic Host Config uration Protocol (DHCP) client. Use the no form of this command to remo ve the co nfigured client name.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1149 default-router <address> <secondary> Use the default-router command to specify the default primary and secondary routers to use for the Dynamic Host Configuration Protocol (DHCP) client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1150 dns-server <address> <secondary> Use the dns-ser ver command to specify the de fault primary and secondary Domain Name System (DNS) servers to use for the Dynamic Host Configuration Protoco l (DHCP) client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1151 domain-name <domain> Use the domain-name command to specify the domain name for the Dynamic Host Configuration Protocol (DHCP) client. Use the no form of this command to remo ve the configured domain name .
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1152 hardware-address <hardware-addres s> <type> Use the hardware-addres s command to specify the name of a Dy namic Host Configuration Protocol (DHCP) client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1153 Default V alues By default, the hardware addr ess type is set to 10 Mbps Ethernet. Applicable Plat forms This command applies to the NetV ant a 300, 1000, 1000R, 2000, 3000 , 4000, and 5000 and T ota l Access 900 Series unit s.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1154 host <address> [ <subnet mask> or < prefix length> ] Use the host command to specify the IP address and subnet mask for a manual binding to a Dynamic Host Configuration Protocol (DHCP) client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1155 lease <days> <hours> <minutes> Use the lease command to specify the duration of the lease fo r an IP address assigned to a Dynamic Host Configuration Protocol (DHCP) client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1156 netbios-name-server <address> <secondary> Use the netbios-name-server command to specify the pri.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1157 netbios-node-type <type> Use the netbios-node-type command to specify the type of NetBIOS node used with Dynamic Host Configuration Protocol (DHCP) clients.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1158 network <address> [ <subnet mask> or < prefix length> ] Use the network command to specify the su bnet number and mask fo r an AOS Dynamic Host Configuration Protocol (DHCP) server address pool.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1159 ntp-server <ip address> Use the ntp-server command to specify the name of the Networ k Time Protoc ol (NTP) server published to the client. Synt ax Description <ip address> S pecifies th e IP addre ss of the NT P server .
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1160 option <option value> [ascii | hex | ip] <value> Use the option command to describe a generic DHCP option to be published to the client. The u ser may specify any number of generic options to be publishe d to the client.
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1161 tft p - s e r v e r <server> Use the tftp-server command to specify the IP address or DNS name of the TFTP server published to the client. Synt ax Description <server> S pecifies the DNS name or dotted not ation IP address of the server .
Command Refere nce Guide DHCP Pool Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1162 timezone-offset <offset> Use the timezone-offset command to specify the time zone adjustment (in hours) published to the client. Synt ax Description <offset> S pecifies the timezone adjustment (in hou rs) published to the cli ent.
Command Refere nce Guide Quality of Ser v ice (QoS) Map Commands 61200990L1-35E Copyright © 2005 ADTRAN 1163 Q UALITY OF S ERVICE (Q O S) M AP C OMMANDS A QoS policy is defined using a Qo S map in the AOS CLI. The QoS ma p is a named list with sequenced entries.
Command Refere nce Guide Quality of Ser v ice (QoS) Map Commands 61200990L1-35E Copyright © 2005 ADTRAN 1164 bandwidth [percent | remaining | <value> ] Use the bandwidth command to provide the bandwidth value of an interface to the higher-level protocols.
Command Refere nce Guide Quality of Ser v ice (QoS) Map Commands 61200990L1-35E Copyright © 2005 ADTRAN 1165 match Use the match command to specify which traffic should be pr oce ssed by this QoS map.
Command Refere nce Guide Quality of Ser v ice (QoS) Map Commands 61200990L1-35E Copyright © 2005 ADTRAN 1166 priority The priority command provides a high-priority queue, prioritiz ing this traffic above all others.
Command Refere nce Guide Quality of Ser v ice (QoS) Map Commands 61200990L1-35E Copyright © 2005 ADTRAN 1167 set dscp <0-63> The set dscp command is an optional command for a Qo S m ap that can be used to modify the DSCP field (on matching packets) to the specified value.
Command Refere nce Guide Quality of Ser v ice (QoS) Map Commands 61200990L1-35E Copyright © 2005 ADTRAN 1168 set precedence <0-7> The set precedence command is an optional command for a QoS map that can be used to modify the IP precedence value (on matching packets) to the specified value.
Command Refere nce Guide Radius Group Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1169 R ADIUS G ROUP C OMMAND S ET To activate the Radius Group mode, enter the aaa group server command at the Global Configuration mode prompt.
Command Refere nce Guide Radius Group Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1170 server [acct-port <port number> | auth-port <port number> ] Use the server command to add a predefined RADIUS server to the current named list of servers.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1171 R OUTE M AP C OMMAND S ET To activate the Route Map Interfa ce Configuration mode, enter the route-map command at the Glob al Configuration mode prompt.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1172 match as-p ath <name> Use the match as-path command to configure the route map to ro ute traffic based on the AS path list name. Use the no form of this command to discontinue matching.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1173 match community <name> [exact-match] Use the match community command to configure the route map to route traffic based on a specified community. Use the no form of this command to discont inue matching.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1174 match ip address <access list name> Use the match ip address command to configure the route map to route traffic based on the access list name defined with the ip access-list command.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1175 match ip address prefix-list <prefix-list name> Use the match ip address prefix-list command to configure the route ma p to route traffic based on a prefix list route filter.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1176 match ip dscp [ <value> | af xx | cs xx | default | ef] Use the match ip dscp command to configure the route map to ro ute traffic based on the Differentiated Services Code Point (DSCP) value in th e IP header of the packet.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1177 match ip precedence [ <value> | critical | flash | flash-override | immediate | internet | netw ork | .
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1178 match metric <value> Use the match metric command to configure the route map to ro ute traffic based on a specified metric value. Use the no form of this command to discontinue matching.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1179 match length <minimum> <maximum> Use the match length command to configure the rout e map to route traffic based on the packet length. Use the no form of this command to discontinue matching.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1180 set as-p ath prepend [ <number> | last-as <number> ] Use the set as-path prepend command to prepend a number to the AS path to influence the best -path selection process by making the AS path appear further away.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1181 set comm-list <name> delete Use the set comm-list delete command to specify a list of communities to delete. Use the no form of this command to disable t h is feature.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1182 set local-preference <value> Use the set local-preference command to restrict traffic to a local autonomous system. Use the no form of this command to cancel the local preference.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1183 set metric <value> Use the set metric command to specify a metric value for the route map. Use the no form of this command to cancel the metric value. Synt ax Description <value> Sets th e metric value.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1184 set default interface <interface type> <interface id> Use the set default interface command to specify an outp ut interface for the packet if there is no explicit route destination.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1185 set interface <interface type> <interface id> Use the set interface command to specify an output interface for the packet. Mu ltiple interfaces can be specified.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1186 set ip default next-hop <ip address> Use the set ip default next-hop command to specify an IP address for the next hop if there is no explicit route destination.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1187 set ip df Use the set ip df command to identify the packet as “don’t fragment” (DF). Use the no form of this command to remove this designation. Synt ax Description No subcommands.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1188 set ip dscp [ <value> | af xx | cs xx | default | ef] Use the set ip dscp command to set the Differentiated Services Co de Point (DSCP) value in the IP header of the packet.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1189 set ip next-hop <ip address> Use the set ip next-hop command to specify the interface for the next hop. Multiple IP addresses can be specified. The packet is forwarded along the first usable IP address.
Command Refere nce Guide Route Map Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1190 set ip precedence [ <value> | critical | flash | fl ash-override | immediate | internet | network | priority | routine] Use the set ip precedence command to set the precede nce value in the IP header of the packet.
Command Refere nce Guide TACACS+ Group Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1191 T ACACS+ G RO UP C ONFIGURATION C OMMAND S ET To activate the Terminal Access Controller Access Control System Plus (TACACS+) Group Configuration mode, enter the aaa gr oup server ta cacs+ command at the Global Configuration mode prompt.
Command Refere nce Guide TACACS+ Group Configuration Command Set 61200990L1-35E Copyright © 2005 ADTRAN 1192 server <host> Use the serve r command to specify a particular TACACS+ server’s IP address or host name. Synt ax Description <host> S pecifies a T ACACS+ server IP address.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1193 Index A aaa accounting commands 284 aaa accounting suppress null-username 285 aaa accounting update 286 aaa authentication 2.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1194 client-identifier 1146 client-name 1148 clock auto-correct-dst 76 , 305 clock no-auto-correct-dst 77 clock set 78 , 306 cloc.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1195 debug sntp 135 debug spanning-tree 137 debug spanning-tree bpdu 136 debug system 138 debug tacas+ packets 139 debug tftp 140.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1196 hold-timer 1094 , 1100 host 1154 hostname 342 HSSI Interface Configuration command set 599 I IKE Client command set 1063 IKE.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1197 ip snmp agent 408 ip sntp source-interface 409 ip ssh-server 410 ip subnet-zero 411 ip telnet-server 410 ip tftp source-inte.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1198 qos-policy out 579 , 710 , 963 R Radius Group command set 1169 radius-server 436 radius-server host 438 redistribute connect.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1199 show output-startup 240 show power supply 241 show processes 243 show qos map 245 show queue 249 show queuing 250 show radiu.
Command Refere nce Guide Index 61200990L1-35E Copyright © 2005 ADTRAN 1200 W warranty 3 write 280.
Een belangrijk punt na aankoop van elk apparaat ADTRAN 5000 Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ADTRAN 5000 Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ADTRAN 5000 Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ADTRAN 5000 Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ADTRAN 5000 Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ADTRAN 5000 Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ADTRAN 5000 Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ADTRAN 5000 Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
