Gebruiksaanwijzing /service van het product GD4130-WH van de fabrikant Datalogic
Ga naar pagina of 428
Gr yphon ™ I GD4100/GM4100 General P urpose Handheld Linear I mager Bar code Reader P roduct Referenc e Guide .
Datalogic Scanning, Inc. 959 T err y Street Eugene, Oregon 974 02 USA T eleph one: (541 ) 683-5700 F ax: (541) 345- 7140 An Unpublished Work - All rights reser ved.
Pr oduct Reference Guide 1 T able of C ont ents Introduction ............................................................................................. ...................... ..................................................... .............. 9 About this Guide .
Contents 2 Gryphon™ I GD4100/GM4100 Contrast ....................... .............................. ......................................... ........................ ....... .............................. ......................................... .
Contents Pr oduct Reference Guide 3 Wand Emulation Interface ........................................................................................................... ............................................... 123 Introduction .................
Contents 4 Gryphon™ I GD4100/GM4100 UPC-E ...................................... ........................................ ............................... ............ ............................. ......................................... ..........
Contents Pr oduct Reference Guide 5 Code 128 Minimum Reads ...................................... ................................................... ............... ......................... ............................... ...........................
Contents 6 Gryphon™ I GD4100/GM4100 Datalogic 2 of 5 Enable/Disable .......................................................... ..................................... .... ............................... ........................................ ......
Contents Pr oduct Reference Guide 7 Code 93 Set Length 1 .................................................................... ...................................... ............. ......................................... ..............................
Contents 8 Gryphon™ I GD4100/GM4100 Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode ...................................... ............................. . ......................................... ................................... 414 Digital Interface .
Pr oduct Reference Guide 9 Chapter 1 Intr oduc tion About this Guide This Product Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming , maintenance and specifications.
Introduction 10 Gryphon™ I GD4100/GM4100 Chapter 11, Data Ed iting offers advanced configuration options for customization of scanned data output. Chapter 12, RF F eatures describes options and programming related to the reader’s radio communication features.
Technical Support P roduct Reference Guide 11 T echnical Supp or t Datalogic W ebsite Suppor t The Datalogic website ( www .scanning.datalogic.c om ) is the c omplete sour ce for technica l support and information for Datalogic products .
Introduction 12 Gryphon™ I GD4100/GM4100 NO TES.
P ro d u ct R e fe re n ce G u id e 13 Chapter 2 Getting Star ted About the Reader Advancements in the LED technology used in this reader significantly improve the illumination of the target field of view, resulting in higher sc an efficiency.
Getting Started 14 Gryphon™ I GD4100/GM4100 Battery Safety To install, charge and/or do any other action on the battery, follow the instructions in this manual. NO TE Before installing the Ba ttery , read “Ba ttery Safety” on this and the following pages .
Setting Up the Reader Product Reference Guide 15 As with other types of batteries, Lithium-Ion (LI) batteries will lose capacity over time. Cap acity deterioration is noticeable after one year of service whether the battery is in use or not.
Getting Started 16 Gryphon™ I GD4100/GM4100 Install the Batt eries To install or change the ba ttery of your reader, you mu st: 1. Wit h a s cre wdri ver , unsc rew the b at ter y cover sc rew . 2. U nplug th e three screws securing the battery holder , and unplug the white connector .
Install the Interface Cable Product Reference Guide 17 6. Insert the co ver in the handle and screw it back into place. Install the Inter face C able For Corded versions, c onnect the reader cable by inserting th e cable into the handle as shown in Figure 1 .
Getting Started 18 Gryphon™ I GD4100/GM4100 Figur e 2. RS-232 Connect ion Ke yboard W edge Connection The Keyboard Wedge cable has a ‘Y’ connection from the read er. Connect the female to the male end from the keyboard and the remaining en d at the keyboard port at the terminal/PC.
Install the Interface Cable Product Reference Guide 19 Fi g ur e 4 . USB conn ection Other connection types are described below and il lustrated in Figure 5 . F igure 5. Other Inter face C onnections U S B I B M K e y b o a r d W e d g e or ... or ...
Getting Started 20 Gryphon™ I GD4100/GM4100 C o nfiguring the Base Sta tion The base charger/station may be configured in desk application to hold the reader in two different positions, either a horizontal or st anding position, in order to provide the most comfortable use depending on needs.
Configuring the Base St ation Product Reference Guide 21 1. Insert the appropriate parts for the desired base station position, as shown belo w . 2. U sing your thumbs, push open the plastic tabs on the bottom of the base to free the wing holders. Ta b Ta b 3.
Getting Started 22 Gryphon™ I GD4100/GM4100 C onnect the Base Station Figure 6 shows how to connect the Base Station t o a terminal, PC or other host device. Turn off the host before connection and consult the manu al for that equipment (if necessary) before proceeding.
Configuring the Base St ation Product Reference Guide 23 Fi g ur e 7 . Options for routing the DC c ord Please refer to the arrows depicted on the bottom of the base when placing the cables, detailed in Figure 8 . Figure 8. Ar rows s howi ng ro uti ng Host C onnection.
Getting Started 24 Gryphon™ I GD4100/GM4100 Pow e r C o n n e c t i o n . Plug the AC Adapter in to an approved AC wall socket with the cable facing downwards (as shown in Figure 6 ) to preven t undue strain on the socket.
GRYPHON™ I Sy stem and Network Layo uts Product Reference Guide 25 GR Y PHON™ I Sy stem and Network La youts Stand Alone La y outs Fi g ur e 1 1 . Single Reader Lay out Fi g ur e 1 2 . Multiple Reader Layout In stand alone systems, each cradle is connected to a single Host.
Getting Started 26 Gryphon™ I GD4100/GM4100 Fi g ur e 1 3 . Multiple Stand Alone Lay outs Many stand alone connections can operate in th e same physical area without interference, provided all readers and cradles in the system have different addresses.
Using the BC40xx™ Radio Base Product Reference Guide 27 U sing the BC40xx™ Radio Base Base LEDs LEDs on the Gryphon I Base provide informat ion about the Base’s status, as shown in Figure 14 . Fi g ur e 1 4 YELLOW LED RED LED — GREEN LED BUTTON .
Getting Started 28 Gryphon™ I GD4100/GM4100 Displa y The Gryphon GM4100 is available with a n option al Display. The Display features 4 lines and 16 characters, and offers icons and three additional keys to allow a better interaction with a remote host.
Programming Product Reference Guide 29 Select the Inter face T ype Upon completing the physical connection between the reader and its host, proceed direc tly to "Interfaces"on page 67 for information and programming for the in terface type the reader is connected to (for example: RS-232, Keyboard Wedge, USB, etc.
Getting Started 30 Gryphon™ I GD4100/GM4100 Co n f i g u r e O t h e r Fe at u re s If your installation requires different programming than the st andard factory default settings, the following sections of this manual allow configuration of non-interface-specific settings you might require: General F eatures .
Programming Product Reference Guide 31 Restore F ac tory Configura tion If you want to restore the Factory Configuration for your imager, scan either the Restore USA Factory Configuration barcode or the Restore EU Factory Configuration barcode below.
Getting Started 32 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 33 Chapter 3 General F eatures Double Read T imeout To prevent a double read of the same label, the Double Read Timeout sets the minimum time allowed between reads of labels of the same sy mbology and data.
General Fe atures 34 Gryphon™ I GD4100/GM4100 Double Read T imeout — c ontinued ENTER/EXIT PROGRAMMING MODE Double Read Timeout = 0.5 S econd Double Read T imeout = 0. 6 Second Double Read Timeout = 0.7 S econd Double Read T imeout = 0. 8 Second Double Read Timeout = 0.
Label Gone Timeout Product Reference Guide 35 Label Gone T imeout This feature sets the time after the last label segm ent is seen before the reader prepares for a ne w label. The timeout can be set within a range of 10 milliseconds to 2,550 milliseconds (2.
General Fe atures 36 Gryphon™ I GD4100/GM4100 Label Gone T imeout — co nt. ENTER/EXIT PROGRAMMING MODE Select Label G one Timeout Setting Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Sleep Mode Timeout Product Reference Guide 37 Sleep Mode T imeout Specifies the timeout value for the r eader to en ter low power Sleep Mode. When Sleep Mode is enabled the reader cannot receive comm ands from the Host or base station. In order for the reader to enter Sleep Mo de, the following cond itions must be met: Cor de d ve rs i on .
General Fe atures 38 Gryphon™ I GD4100/GM4100 Sleep Mode Timeout — c ontinued ENTER/EXIT PROGRAMMING MODE Sleep Mode Timeout = 5 Seconds Sleep Mode Timeout = 6 Seconds Sleep Mode Timeout = 7 Seconds Sleep Mode Timeout = 8 Seconds Sleep Mode Timeout = 9 Seconds Sleep Mode Timeout = 10 Seconds max.
LED and Beeper Indicators Product Reference Guide 39 LED and Beeper Indicators Po we r O n A l e r t Disables or enables the indication (from the Beeper) that the reader is receiving power.
General Fe atures 40 Gryphon™ I GD4100/GM4100 Good Read: When t o Indicat e This feature specifies when t he reader will provid e indication (beep and/or flash its green LED) upon successfully readin g a barcode.
LED and Beeper Indicators Product Reference Guide 41 Good Read Beep T ype Specifies whether the good read beep has a mono or bitonal beep sound. ENTER/EXIT PROGRAMMING MODE Good Read Beep T ype = M on.
General Fe atures 42 Gryphon™ I GD4100/GM4100 Good Read Beep F requency Adjusts the good read beep to sound at a selectab le low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.) Good Read Beep Length Specifies the duration of a good read beep.
LED and Beeper Indicators Product Reference Guide 43 Good Read Beep Length — c ontinued ENTER/EXIT PROGRAMMING MODE Good Read B eep Length = 80 msec Good Read Beep Le ngth = 100 msec Good Read Beep .
General Fe atures 44 Gryphon™ I GD4100/GM4100 Good Read Beep V olume Selects the beeper volume (loudness) upon a good read beep. There are three se lectable volume levels.
LED and Beeper Indicators Product Reference Guide 45 Good Read LED Dura tion This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 10 milliseconds to 2,55 0 milliseconds (0.
General Fe atures 46 Gryphon™ I GD4100/GM4100 Good Read LED Dura tion — c ont . ENTER/EXIT PROGRAMMING MODE Select G ood Read LED Duration Setting Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Scanning Features Product Reference Guide 47 Scanning F eatur es Scan Mode Selects the scan operating mode for the reader. Selections are: Tr i g g e r S i n g l e .
General Fe atures 48 Gryphon™ I GD4100/GM4100 Scan Mod e — c ont inu ed ENTER/EXIT PROGRAMMING MODE Scan Mode = T rigger Single Scan Mo de = T rigger Hold Multiple Scan Mode = T rigger Pulse Multi.
Scanning Features Product Reference Guide 49 Stand Mode T riggered T imeout This feature specifies the time to remain in Tr i g g e r S i n g l e mode after the trigger is pulled while in St an d Mo d e . NO TE ENTER/EXIT PROGRAMMING MODE Stand Mode T r iggered Timeout = 0.
General Fe atures 50 Gryphon™ I GD4100/GM4100 Stand Mode T riggered T imeout — continued ENTER/EXIT PROGRAMMING MODE Stand Mode T r iggered Timeout = 6 Seconds Stand Mode T r iggered Timeout = 8 S.
Scanning Features Product Reference Guide 51 Stand D etec tio n Specifies the behavior of the scanner when p lac ed in a stand that co ntains autorecognition hardware.
General Fe atures 52 Gryphon™ I GD4100/GM4100 Stand Mode Sensitivity Sets the sensitivity level for stand mode wakeup. Choices are low, medium and high.
Scanning Features Product Reference Guide 53 Scanning Active T i me This setting specifies the amount of time t hat the reader stays in scan ON state once the state is entered. The range for this setting is from 1 to 255 seconds in 1-second increments.
General Fe atures 54 Gryphon™ I GD4100/GM4100 Scanning Active T ime — c ont. ENTER/EXIT PROGRAMMING MODE Select Scann ing A ctive T ime Sett ing Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Flash On Time Product Reference Guide 55 Fl a s h O n Ti m e This feature specifies the ON time for the indi cator LED while in Flash Mode. The selectable range is 100 to 9,900 millise conds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feat ure.
General Fe atures 56 Gryphon™ I GD4100/GM4100 Fla s h O n Tim e — c on t. ENTER/EXIT PROGRAMMING MODE Select Fl ash ON T ime Settin g Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Flash Off Time Product Reference Guide 57 F lash Off T ime This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 millise conds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feat ure.
General Fe atures 58 Gryphon™ I GD4100/GM4100 Fla s h O f f Ti me — con t. ENTER/EXIT PROGRAMMING MODE Sel ect F la sh OFF T im e Se tt in g Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Green Spot Duration Product Reference Guide 59 Green Spot Dura tion Specifies the duration of the good re ad pointer beam after a good read. ENTER/EXIT PROGRAMMING MODE Green Spot Duration = Disable (.
General Fe atures 60 Gryphon™ I GD4100/GM4100 Displa y Co nt r a s t Read the code until the desired contrast is reached. Fo n t S i z e ENTER/EXIT PROGRAMMING MODE F ont size = small F ont size = M.
Display Product Reference Guide 61 Backlight ENTER/EXIT PROGRAMMING MODE Display backlight = off Display backlight = on DEF A UL T $ $.
General Fe atures 62 Gryphon™ I GD4100/GM4100 Displa y Mode The user can control the reader display beha vior according to the following selections: Local Echo mode: When a barcode is read with the reader: • The code is sent to the H ost. • The reader display is cleared.
Display Product Reference Guide 63 Display T imeout Specifies how long the display will remain on after a display write. Display is forced on after any display write or after any reading phase. Displa y and backlight are turned off after this timeout expires.
General Fe atures 64 Gryphon™ I GD4100/GM4100 Display T imeout (continued) ENTER/EXIT PROGRAMMING MODE Display T imeout = 5 Seconds Display T imeout= 6 Seconds Display T imeout = 7 Seconds Display Timeout = 8 Seconds Display T imeout = 9 Seconds Display T imeout = 9.
Keypad Select Product Reference Guide 65 Key p a d S e l e c t This parameter specifies the character that has to be sent from the scanner when one of the three keys are pressed. For example, when key1 is pressed a 0x3C '< ' character is sent.
General Fe atures 66 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 67 Chapter 4 Inter faces Inte r face Selection Each reader model will support one of the following sets of host interfaces: General P urpose Models RS-232 RS-232 OPOS USB Key.
Interfaces 68 Gryphon™ I GD4100/GM4100 Ta b l e 6. A vailable Interfaces RS-232 FEA TURES RS-232 standard interface Select RS232-STD Set RS-232 Int erfa ce Fe a t u re s starting on page 73 Selec t RS232-WN RS-232 Wincor-Nix dorf RS-232 for use with OPOS/UPOS/Jav aPOS Select RS-232 OPOS Sel ect U SB-C OM-ST D a a.
Configuring the Interface Product Reference Guide 69 KEY BO ARD FEA TURES A T , PS/2 25-286, 30-286, 50, 5 0Z, 60, 70, 80, 90 & 95 w/St andard K ey Enc oding Select KBD -A T Set KEYB OARD WEDGE In.
Interfaces 70 Gryphon™ I GD4100/GM4100 KEYBO ARD — con t. FEA TURES Ke yboard W edge for IBM T erminals 31xx, 32xx, 34xx, 37xx make only k ey- board Select KBD-IBM-M Set KEY BOA RD WEDGE Int erfa .
Global Interface Features Product Reference Guide 71 Global Inter face F eatures The following interface features are configurable by all interface type s.
Interfaces 72 Gryphon™ I GD4100/GM4100 USB Suspend Mode This setting enables/disables the ability of USB interfaces to enter suspend mode. ENTER/EXIT PROGRAMMING MODE USB Suspend Mode = Disable USB .
Pr oduct Refer ence Guide 73 Chapter 5 RS-232 ONL Y Inter fac e Introduction Use the programming barcodes in this chapter if modificat ions to the standard RS-232 interface settings are necessary to meet your system’s requirements.
RS-232 ONLY Interface 74 Gryphon™ I GD4100/GM4100 Baud Rate — con tinued ENTER/EXIT PROGRAMMING MODE Baud Rate = 9600 Baud Rate = 19,200 Baud R ate = 38,400 Baud Rate = 57,600 Baud Rate = 115,200 .
Data Bits Product Reference Guide 75 Data Bits This parameter allows the reader to interface with devices requiring a 7-bit or 8-bit ASCI I protocol for sending and receiving data.
RS-232 ONLY Interface 76 Gryphon™ I GD4100/GM4100 Pa r i t y This feature specifies parity required for sendin g and receiving data. A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements.
Handshaking Control Product Reference Guide 77 Handshaking Con trol The data interface consists of an RS-232 port designed to operate either with or without the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS). Handshaking Control includes the following options: • R TS — R TS is asserted during transmissions.
RS-232 ONLY Interface 78 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 79 Chapter 6 RS -232/USB - C om Inter faces Introduction The programming barcodes in this chapter allow modifications to the standard RS-232 and USB-Com interfaces. Stan dard F ac to r y Se tt ing s Referenc e Appendix C, Standard Defaults for a listing of standard factory settings.
RS-232/USB-Com Interfaces 80 Gryphon™ I GD4100/GM4100 Inter charac ter Dela y This parameter specifies the intercharacter de lay be tween the end of one character and the beginning of the next. The delay can be set with in a range of zero (0) to 990 milliseconds in 10ms increments.
Intercharacter Delay Product Reference Guide 81 Intercharacter Delay — c ont. ENTER/EXIT PROGRAMMING MODE Inter cha racte r Delay = No Dela y Se lec t I nterch arac ter Del ay Se tti ng Make a mistake? Scan the CANCEL barcode to abort and not save the entry string.
RS-232/USB-Com Interfaces 82 Gryphon™ I GD4100/GM4100 Beep On ASCII BEL When this parameter is enabled, the reader issues a beep when a <BEL> ch aracter is detected on the RS-232 serial line. <BEL> is issued to gain a user's attention to an illegal entry or other important event.
ACK NAK Options Product Reference Guide 83 A CK NAK Options This enables/disables the ability of the read er to support the RS-2 32 ACK/NAK protocol. When configured, the reader and/or host sends an “ACK” wh en it receives data properly, and sends “NAK” when the data is in error.
RS-232/USB-Com Interfaces 84 Gryphon™ I GD4100/GM4100 A CK Character This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII characters or any hex value from 0 to 0xFF can be selected. NO TE To set this feature: 1.
ACK NAK Options Product Reference Guide 85 A CK Charac ter — cont. ENTER/EXIT PROGRAMMING MODE Selec t ACK Character S etting DEF A UL T 0x06 ‘ ACK’ Char ac ter.
RS-232/USB-Com Interfaces 86 Gryphon™ I GD4100/GM4100 NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected. NO TE To set this feature: 1.
ACK NAK Options Product Reference Guide 87 NAK Character — con t. ENTER/EXIT PROGRAMMING MODE Select NAK Character Setting DEF A UL T 0x15 ‘NAK ’ Character.
RS-232/USB-Com Interfaces 88 Gryphon™ I GD4100/GM4100 AC K N A K Ti m e o u t Val u e This option specifies the amount of time the re ader waits for an ACK character from the host following label transmission. The selectable time out range is 200 milliseconds to 15,000ms (15 seconds) in 200ms increments.
ACK NAK Options Product Reference Guide 89 A CK NAK T imeout V alue — cont. ENTER/EXIT PROGRAMMING MODE Select ACK NAK T imeout V alue Setting Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
RS-232/USB-Com Interfaces 90 Gryphon™ I GD4100/GM4100 AC K N A K R e t r y C o u n t This feature specifies the number of times the re ader retries a label tran smission due to a retry condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and a selection of 255 specifies unlimited retries.
ACK NAK Options Product Reference Guide 91 A CK NAK Retry Count — con t. ENTER/EXIT PROGRAMMING MODE Select ACK NAK Retry Count Setting Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
RS-232/USB-Com Interfaces 92 Gryphon™ I GD4100/GM4100 A CK NAK Error Handling This feature specifies the method the reader uses to handle receiv e errors detected while waiting for an ACK character from the host.
Indicate Transmission Failure Product Reference Guide 93 Indicate T ransmission F ailure This option enables/disables the reader’s ab ility to sound an error beep to indicate a transmission failure .
RS-232/USB-Com Interfaces 94 Gryphon™ I GD4100/GM4100 Disable Character Specifies the value of the RS -232 host command used to disable the reader. ASCII characters or any hex value from 0 to 0xF F can be selected. NO TE To set the value: 1. Determine the desired character or value.
Disable Character Product Reference Guide 95 Disable Character — con t. ENTER/EXIT PROGRAMMING MODE Selec t Disable Charac ter Setting DEF A UL T 0x44 = Disable Char acter is ‘D’.
RS-232/USB-Com Interfaces 96 Gryphon™ I GD4100/GM4100 Enable Character Specifies the value of the RS -232 host command used to enable the re ader. ASCII characters or any hex value from 0 to 0xF F can be selected. NO TE To set this feature: Determine the desired character or value.
Enable Character Product Reference Guide 97 Enable Character — con t. ENTER/EXIT PROGRAMMING MODE Select En able Charac ter Setting DEF A UL T 0x45 = Enable Char acter is ‘E’.
RS-232/USB-Com Interfaces 98 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 99 Chapter 7 K eyboard In ter fac e Introduction Use the programming barcodes in this chapter to select options for USB Keyboard and Wedge Interfaces. Stan dard F ac to r y Se tt ing s Referenc e A ppendix C, Standar d Defaults for a listing of standard factory settings.
Keyboard Interface 100 Gryphon™ I GD4100/GM4100 Country Mode This feature specifies the country/la nguage supported by the ke yboard. Only the following interfaces support ALL Country Modes.
Country Mode Product Reference Guide 101 C ountry Mode — continued ENTER/EXIT PROGRAMMING MODE Count r y M od e = D en mar k Support s only the interfaces listed in the C ountr y Mode featur e description. Countr y M ode = France Cou nt r y M od e = G er ma ny Supports only the interfaces listed in the C ountry Mode fea- ture description.
Keyboard Interface 102 Gryphon™ I GD4100/GM4100 C ountry Mode — continued ENTER/EXIT PROGRAMMING MODE Country M ode = Poland Support s only the interfaces listed in the C ountr y Mode featur e description. Supports only the interfaces listed in the Country Mode fea- ture description.
Caps Lock Sta te Product Reference Guide 103 Cap s Loc k St ate This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alternate key encoding keyboard is selected.
Keyboard Interface 104 Gryphon™ I GD4100/GM4100 Send Contr ol Charac ters This feature Specifies how the reader transmits ASCII control characters to the hos t. Reference Appendix F , Scancode T ables for more information about control characters. Options are as follows: Con trol Char acter 00 .
Wedge Quiet Interval Product Reference Guide 105 We d g e Q u i e t I n t e r v a l This option specifies the amount of time to look for keyboard activity before the reader breaks the keyboard connection in order to transmit data to host. The selectable range for this feature is from 0 to 990ms in 10ms increments.
Keyboard Interface 106 Gryphon™ I GD4100/GM4100 We d g e Q u i e t I n t e r v a l — c o n t . ENTER/EXIT PROGRAMMING MODE Select Wedge Quiet Interval Setting Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Intercharacter Delay Product Reference Guide 107 Inter charac ter Dela y This parameter specifies the intercharacter de lay be tween the end of one character and the beginning of the next. The delay can be set with in a range of zero (0) to 990 milliseconds in 10ms increments.
Keyboard Interface 108 Gryphon™ I GD4100/GM4100 Inte rchar ac ter Delay — c ont . ENTER/EXIT PROGRAMMING MODE Inter cha racte r Delay = No Dela y Se lec t I nterch arac ter Del ay Se tti ng Make a mistake? Scan the CANCEL barcode to abort an d not save the entry string.
Intercode Delay Product Reference Guide 109 Inter code Delay Specifies the delay between labels transmitted to the hos t for this interface. The selectable range for this feature is from 0 to 99 seconds. Follow these instructions to set this feat ure: 1.
Keyboard Interface 110 Gryphon™ I GD4100/GM4100 Inte rc ode Delay — c ont . ENTER/EXIT PROGRAMMING MODE Set Inte rc ode Dela y Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
USB Keyboard Speed Product Reference Guide 111 USB K eyboar d Speed This option specifies the USB poll rate for a USB keyboard. NO TE ENTER/EXIT PROGRAMMING MODE USB Keyboard Speed = 1ms USB Keyboard Speed = 2ms USB Keyboard Speed = 3ms USB Keyboard Speed = 4ms USB Keyboard Speed = 5ms This fe ature applies ONL Y to the USB Keyboard in terface.
Keyboard Interface 112 Gryphon™ I GD4100/GM4100 USB K eyboard Speed — c ontinued ENTER/EXIT PROGRAMMING MODE USB Keyboard Speed = 6ms USB Keyboard Speed = 7ms USB Keyboard Speed = 8ms USB Keyboard.
Pr oduct Refer ence Guide 113 Chapter 8 USB - OEM Inter face Introduction Feature settings for USB interfaces differ depend ing upon which host type the reader will be connected with. Use the feature settings in this chapter and Chapter 9, IBM 46XX Interface to specifically configure for the USB-OEM inte rface.
USB-OEM Interface 114 Gryphon™ I GD4100/GM4100 USB- OEM Device U sage The USB-OEM protocol allows for the reader to be identified as one of two different types of barcode scanners. Depending on what other sc anners you may already have connected to a USB-OEM POS, you may need to change this se tting to enable all devices to communicate.
Interface Options Product Reference Guide 115 Inte r face Options ENTER/EXIT PROGRAMMING MODE Obey Scanner C onfigura tion Host Com mands Ignore Scanner Configuration Host Commands This feature provides for an inte rface-specific control mechanism.
USB-OEM Interface 116 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 117 Chapter 9 IBM 46X X Inter face Introduction Use the barcodes in this section to configure programmable features for available IBM 46XX interfaces. IBM Standard F a c tory S ettings Referenc e A ppendix C, Standar d Defaults for a listing of standard factory settings.
IBM 46XX Interface 118 Gryphon™ I GD4100/GM4100 46xx Number of Host Resets Specifies how many consecutive resets are processe d before the reader starts a five-second period to allow the user to enter Programming Mode and configure the reader. The configurable range for this feature is 1 to 15 resets.
ENTER/EXIT PROGRAMMING MODE 46xx Number of Host Resets = 7 46xx Number of Ho st Resets = 8 46xx Number of Host Resets = 9 46xx Number of Host Resets = 10 46xx Number of Host Resets = 11 46xx Number of Host Resets = 12 46xx Number of Host R esets Product Reference Guide 119 46xx Number of Host Resets — c ont.
ENTER/EXIT PROGRAMMING MODE 46xx Number of Host Resets = 13 46xx Number of Host Resets = 14 46xx Number of Host Resets = 15 IBM 46XX Interface 120 Gryphon™ I GD4100/GM4100 46xx Number of Host Resets — c ont.
Transmit Labels in Code 39 Format Product Reference Guide 121 T ransmit Labels in Code 39 F ormat This feature enable/disables tran slation to Code 39 before transmitting label data to an IBM- 46XX or a USB-OEM host. Only the symbology iden tifier is modified for the translation.
IBM 46XX Interface 122 Gryphon™ I GD4100/GM4100 Inte r face Options ENTER/EXIT PROGRAMMING MODE Obey Scanner Configur ation Host Commands Ignore Scanner Configuration Host Commands This feature provides for an inte rface-specific control mechanism.
Pr oduct Refer ence Guide 123 Chapter 10 W and Emulation Inter face Introduction This chapter provides feature/settings configuration for the Wand Emulation interface. W and Emulation Standard F ac tor y Settings Referenc e A ppendix C, Standar d Defaults for a listing of standard factory settings.
Wand Emulation Interface 124 Gryphon™ I GD4100/GM4100 Wa n d P o l a r i t y This option specifies the polarity of the Wand output signal. Choices are: • Quiet zones and spaces ar e high, bars are.
Wand Idle State Product Reference Guide 125 Wa n d I d l e S t a t e This feature specifies the level of the Wand output signal when the reader is idle . NO TE ENTER/EXIT PROGRAMMING MODE Wa n d I d l e S t a t e = L o w Wa n d I d l e S t a t e = H i g h TTL logic levels: 0V <= Low <= 0.
Wand Emulation Interface 126 Gryphon™ I GD4100/GM4100 T ransmit Noise This option specifies the leading/tr ailing noise for the Wand interface. Choices are: • Disable (no leading/trailing nois.
Label Symbology Conversion Product Reference Guide 127 Label S ymbology C onv ersion When this feature is enabled for the Wand Emulation interface, all barc ode labels are converted to a single symbology.
Wand Emulation Interface 128 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 129 Chapter 11 Data Editing Data Editing Overview When a barcode is scanned, additional informatio n can be sent to the host computer along with the barcode data. This combination of barcode data and supplementary user-defined data is called a “message string.
Data Editing 130 Gryphon™ I GD4100/GM4100 Please K eep In Mind... • M odifying a message string is not a mandator y requirement. Data editing is sophisticated feature allowing highly customizable output for advanced users. F actor y default settings for data editing is typically set to NONE.
Global Prefix/S uffix Product Reference Guide 131 6. Scan the ENTER/EXIT barcode once again to exit Pr ogramming M ode. 7. The resulting message string would appear as follo ws: Scanned barcode data:1.
Data Editing 132 Gryphon™ I GD4100/GM4100 Global AIM ID AIM label identifiers (as opposed to custom ch aracters you select yourself as with label identifiers) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), follo wed b y .
Global AIM ID Product Reference Guide 133 Global AIM ID — c ontinued ENTER/EXIT PROGRAMMING MODE Global AIM ID = Disable Global AIM ID = Enable DEF A UL T.
Data Editing 134 Gryphon™ I GD4100/GM4100 GS1-128 AIM ID If Global AIM ID is disabled, the AIM ID for GS1-12 8 can be enabled/di sabled independ ently. The AIM ID for GS1-128 is a ]C1, ]C2 or ]C3. AIM IDs for other symbologies can be enable d/disabled independently as well.
Label ID Product Reference Guide 135 Label ID A Label ID is a customizable code of up to th ree ASCII characters (eac h can be one of hex 0x01- 0xFF), used to identify a barcode (symbology) type . It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled.
Data Editing 136 Gryphon™ I GD4100/GM4100 Codablock F l 6C0000 m 6D0000 COD E 11 CE 43 4500 b 620000 COD E 12 8 # 230000 T 540000 COD E 32 A 410000 X 580000 COD E 39 * 2A0000 V 560000 COD E 39 C IP .
Label ID Product Reference Guide 137 Label ID: Set Individually P er Symbology To configure a Label ID individually for a single symbology: 1. Scan the ENTER/EXIT barcode.
Data Editing 138 Gryphon™ I GD4100/GM4100 F igure 19. Label ID P osition Options OR Prefix Su ffix L ab el ID L ab el ID B a r Code D a t a Aim ID Ta b l e 18 . Label ID Examples STEP AC T I O N EXAMPLES 1. Scan the ENTER/EXIT barc ode (Scanner ent ers P rog ramming Mode) 2.
Label ID Product Reference Guide 139 Result: DB*[barcode data] [barcode data]=C3 +[barcode data] [barc ode data]PH STEP A C TION EXAMPLES 1. Scan the ENTE R/EXIT barc ode (Scanner ent ers P rog ramming Mode) 2.
Data Editing 140 Gryphon™ I GD4100/GM4100 Label ID C on trol This option controls whether a Label ID is disabl ed, or sent as a prefix or suffix for a given symbology type.
Label ID Product Reference Guide 141 Label ID S ymbology Selection This option selects the symbology for whic h a Label ID is to be configured. See "Label ID"on page 135 ENTER/EXIT PROGRAMMI.
ENTER/EXIT PROGRAMMING MODE Set UPC-E/P5 Label ID Char acter(s) Set UPC-E/GS1-128 Label ID Character(s) Set EAN 13 Label ID Charac ter(s) Set EAN 13/P 2 Label ID Character( s) Set EAN 13/P5 Labe l ID .
ENTER/EXIT PROGRAMMING MODE Set EAN 8 Label ID Character(s) Set EAN 8/P2 Label ID Character(s) Set EAN 8/P5 Label ID Character(s) Set EAN 8/GS1 -128 Label ID Charac ter(s) Set GTIN Label ID Charac ter.
ENTER/EXIT PROGRAMMING MODE Set GTIN/P5 Label ID Character(s) Set GTIN/GS1-128 Label ID Charac ter(s) Set Code 39 Label ID Character(s) Set Code 32 Label ID Char acter(s) Set Code 39 CIP Label ID Char.
ENTER/EXIT PROGRAMMING MODE Set ISBT 128 Label ID Cha racter(s) Set Codablock F Label ID Character(s) Set Inter leaved 2 of 5 Label ID Character (s) Set Follett 2 of 5 Label ID Character(s) Set Inter .
ENTER/EXIT PROGRAMMING MODE Set Industrial 2 of 5 Label ID Chara cter(s) Set IA T A Label ID Character(s) Set Datalogic 2 of 5 Label ID Character(s) Set Codabar Label ID Character(s) Set ABC Codabar L.
ENTER/EXIT PROGRAMMING MODE Set DataBar Omnidirectional Label ID Cha racter(s) Set DataBar Expanded La bel ID Character(s) Set DataBar Limite d Label ID Character(s) $ Set Code 93 Label ID Char acter(.
ENTER/EXIT PROGRAMMING MODE Set Code 4 Label ID Charac ter(s) Set Code 5 Label ID Character(s) Data Editing 148 Gryphon™ I GD4100/GM4100 Label ID Symbology Selection — continued.
Case Conversion Product Reference Guide 149 Case C on version This feature allows conversion of the case of a ll alphabetic characters to upper or lower case.
Data Editing 150 Gryphon™ I GD4100/GM4100 Character Con version Character conversion is an eight byte configura tion item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted.
Character Conversion Product Reference Guide 151 Character C on v ersion — co ntinued ENTER/EXIT PROGRAMMING MODE Configure Character Conversion DEF A UL T 0xFFFFFF FFFFFFFF FF (No character c onv e.
Data Editing 152 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 153 Chapter 12 RF F eatur es Introduction This section provides options and programming related to the reader’s radio communication features. Stan dard F ac to r y Se tt ing s Referenc e A ppendix C, Standar d Defaults for a listing of standard factory settings.
RF Features 154 Gryphon™ I GD4100/GM4100 RF Beeper F eatures Several options are a vailable to configure beeper behavior for RF operation. Good T ransmission Beep Enables/disables the Good Tr ansmission Beep in dication. When enabled, a beep occurs when a Label is correctly transmitted to the base.
RF Beeper Features Product Reference Guide 155 Beep F r equency Adjusts radio-specific beep indications to sound at a low, me dium or high frequency, selectable from the list below.
RF Features 156 Gryphon™ I GD4100/GM4100 Beep Dura tion This feature controls the duration of radio-specific beep indications. ENTER/EXIT PROGRAMMING MODE Beep Dura tion = 60 msec Beep Duration = 80.
RF Beeper Features Product Reference Guide 157 Beep Dur a tion — c on t. ENTER/EXIT PROGRAMMING MODE Beep Duration = 160 msec Beep Duratio n = 180 msec Beep Duration = 200 msec.
RF Features 158 Gryphon™ I GD4100/GM4100 Beep V olume Selects the beeper volume (loudness) of radio-specific beep indications. There are three selectable volume levels.
RF Beeper Features Product Reference Guide 159 Disco nnect Beep Enables/disables the beep indication that a ha ndheld has become disconnected from a Base Station. ENTER/EXIT PROGRAMMING MODE Disconnect Beep = Disable Disconnec t Beep = Enable Base Station Beep Enables/disables a beep indicat ion when the handheld is placed in the Base Station.
RF Features 160 Gryphon™ I GD4100/GM4100 Lea s h Al ar m This setting specifies the number of seconds to sound the Leash Mode beeps (three per second) when the handheld goes ou t of range. This is especially useful in instances where the reader might inadvertently have been placed in a bag or cart .
RF Beeper Features Product Reference Guide 161 Leash A larm — con t. ENTER/EXIT PROGRAMMING MODE Leash Alarm = 5 Seconds Leash Alarm = 10 Seconds Leash Alarm = 25 Seconds Leash Alarm = 30 Seconds.
RF Features 162 Gryphon™ I GD4100/GM4100 C onfiguration Update Au tomatic C onfiguration Update When this feature is enabled , a reader and its linked Base Statio n can automatically ensure they stay in sync with regard to application hardware and/or configuration.
Configuration Update Product Reference Guide 163 C opy C onfigura tion to Scanner Scan the following label to copy the current Base Station configuration to the scanner. Use this method when the Auto Configuration Update feature is disabled and you want a one-time configuration update to be performed on the scanner.
RF Features 164 Gryphon™ I GD4100/GM4100 Po we r d o w n Ti m e o u t The Powerdown Timeout feature sets the time for automatically switching the unit off when the imager has been idle.
Powerdown Timeout Product Reference Guide 165 Po we r d o w n Ti m e o u t — c o n t i n u e d ENTER/EXIT PROGRAMMING MODE Po wer down T imeout = 120 Minutes (2 Hours) Po werdown T imeout = 4 Hours .
RF Features 166 Gryphon™ I GD4100/GM4100 Bat ch F eatur es Batch Mode This option specifies whether to store labels in the handheld while disconnected from the base. Options are as follows: • Disabled — The handheld will not store/batch labels. • Manual — The handheld will always store la bels to F lash memory .
RF Address Stamping Product Reference Guide 167 Batch F eatures — cont . Send Ba tch Use this barcode to initiate sending of labels stored in batch memory. NO TE Send Bat ch Erase Ba tch Memor y Use this barcode to erase any lab els stored in b atch memory.
ENTER/EXIT PROGRAMMING MODE Source Radio Addr ess T ransmission = Do Not I nclude Source Radio Address T ransmission = Prefix RF Features 168 Gryphon™ I GD4100/GM4100 NO TE When included as a prefix, the sour ce-radio ID is display ed after all label formatting has been applied.
RF Address Stamping Product Reference Guide 169 Source Radio Address Delimiter Char acter This option specifies the delimiter character to be placed between the label data and radio address when address stamping is enabled. NO TE Follow these instructions to select the delimiter character: 1.
RF Features 170 Gryphon™ I GD4100/GM4100 Source Radio Address Delimiter Char acter — cont. ENTER/EXIT PROGRAMMING MODE Set Source Radio Addr ess Delimiter Character Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string.
Radio Protocol Timeout Product Reference Guide 171 Radio Protoc ol T imeout This parameter sets the valid wait time before transmission between the handheld reader and Base Station is considered failed. When setting this parameter, take into consider ation the radio traffic (n umber of readers in the same area).
RF Features 172 Gryphon™ I GD4100/GM4100 Radio Pr otoc ol T imeout - continued ENTER/EXIT PROGRAMMING MODE Set Ra dio Protocol T imeout Make a mistake? Scan the CANCEL barc ode to abort and not sav e the entr y string. Y ou can then star t again at the beginning.
Radio Transmit Mode Product Reference Guide 173 Radio T ransmit Mode S pecifies the transmission protocol for S tar communications. Options are: • ACK from cradle to scanner — signals a good trans.
RF Features 174 Gryphon™ I GD4100/GM4100 RF Batch Mode T ransmit Dela y Specifies the delay in 10 msec increments between transmitting labels stored in batch memory . ENTER/EXIT PROGRAMMING MODE RF Batch Mode Transmit Delay = No Delay RF Batch Mo de T ransmit D elay = 0.
Pr oduct Refer ence Guide 175 Chapter 13 S ymbologies Introduction The reader supports the following sy mbologies (b arcode types). Options for each symbology are included in this chapter.
Symbologies 176 Gryphon™ I GD4100/GM4100 Standard F ac tor y Settings for Symbologies Default settings are indicated at each feature/ option with a green ar row. Also re ference Appendix C, Standard Defaults for a listing of the most widely used set of standard factory settings.
Code EAN/UPC Product Reference Guide 177 C ode EAN/UPC Co u p o n Co n t r o l This feature is used to control the reader ’s method of processing coupon labels. Options are: • Allow all coupon barcodes to be decoded • Enable only UPC/EAN coupon decoding • Enable only GS1 DataBar™ coupon decoding To set this feature: 1.
Symbologies 178 Gryphon™ I GD4100/GM4100 UPC-A The following options appl y to the UPC-A symbology . UPC-A Enable/ Disable When disabled, the reade r will not read UPC-A barcodes.
UPC-A Product Reference Guide 179 Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data form at. Selecting this feature also changes the symbology ID to match those required for EAN-13.
Symbologies 180 Gryphon™ I GD4100/GM4100 UPC-A Minimum Reads This feature specifies the minimum number of consecutive times a UPC-A lab el must be decoded before it is a ccepted as a good read.
UPC-E Product Reference Guide 181 UPC-E The following options appl y to the UPC-E symb ology. UPC-E Enable/Disable When disabled, the reader will not read UPC-E barcodes. ENTER/EXIT PROGRAMMING MODE UPC-E = Disable UPC-E = Enable UPC-E Check Charac ter T ransmission Enable this option to trans mit the che ck character along with UPC-E barcode data.
Symbologies 182 Gryphon™ I GD4100/GM4100 Expand UPC-E to EAN-13 Expands UPC-E data to the EAN-13 data form at. Selecting this feat ure also changes the symbology ID to match those required for EAN-13.
UPC-E Product Reference Guide 183 UPC-E Number S y stem Char acter T ransmission This feature enables/disables transmission of the UPC-E system number characte r.
Symbologies 184 Gryphon™ I GD4100/GM4100 UPC-E Minimum Reads This feature specifies the minimum number of consec utive times a UPC-E label must be decoded before it is accepted as good read.
GTIN Formatting Product Reference Guide 185 GTIN F ormatting This feature enable s/disables the ability to co nve rt UPC-E, UPC-A, EAN 8 , and EAN 13 labels into the GTIN 14-character format.
Symbologies 186 Gryphon™ I GD4100/GM4100 EAN 13 (Jan 13) The following options apply to the EAN 13 (Jan 13) symbolog y. EAN 13 Enable/Disable When disabled, the reade r will not read EAN 13/JAN 13 barcodes.
EAN 13 (Jan 13) Product Reference Guide 187 EAN-13 F lag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the first character of the label.
Symbologies 188 Gryphon™ I GD4100/GM4100 EAN 13 Minimum Reads This feature specifies the minimum number of consec utive times an EAN 13 label must be decoded before it is accepted as good read.
ISSN Product Reference Guide 189 ISSN The following options apply to the ISSN symbology. ISSN Enable/Disable Enables/disables conversion of EAN/JAN13 Bookla nd labels star ting with 977 to ISSN labels.
Symbologies 190 Gryphon™ I GD4100/GM4100 EAN 8 (Jan 8) The following options apply to the EAN 8 (Jan 8) symbology. EAN 8 Enable/Disable When disabled, the reade r will not read EAN 8/JAN 8 barcodes.
EAN 8 (Jan 8) Product Reference Guide 191 Expand EAN 8 to EAN 13 Enable this option to expand EAN 8/JAN 8 labels to EAN 13/JAN 13 . ENTER/EXIT PROGRAMMING MODE Expand EAN 8 to EAN 13 = Disable Expand .
Symbologies 192 Gryphon™ I GD4100/GM4100 EAN 8 Minimum Reads This feature specifies the minimum number of consec utive times an EAN 8 (Jan 8) label must be decoded before it is accepted as good read.
UPC/EAN Global Settings Product Reference Guide 193 UPC/EAN Global Settings This section provides configuration settin gs for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for ea ch feature description.
Symbologies 194 Gryphon™ I GD4100/GM4100 UPC/EAN Decoding Le v el — con t. ENTER/EXIT PROGRAMMING MODE UPC/EAN Decoding Lev el = 1 UPC/EAN Decoding Level = 2 UPC/EAN Decoding Lev el = 3 UPC/EAN De.
UPC/EAN Global Settings Product Reference Guide 195 UPC/EAN C orrela tion When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Symbologies 196 Gryphon™ I GD4100/GM4100 UPC/EAN Pric e W eight Check This feature enables/disables calculation and verification of price/weight check digits.
UPC/EAN Global Settings Product Reference Guide 197 In-Store Minimum Reads This feature specifies the minimum number of consecutive times an in-store label must be decoded before it is accepted as good read.
Symbologies 198 Gryphon™ I GD4100/GM4100 A dd-Ons The following features apply to optional add-ons. NO TE Optional Add-ons The reader can be enabled to optionally read the following add-ons (supplem.
Add-Ons Product Reference Guide 199 Add-Ons — con t. Optional Add-ons — cont . ENTER/EXIT PROGRAMMING MODE Opti on al A dd-Ons = E nab le P5 Optional A dd-Ons = Disabl e GS1-12 8 Optional Add-On s.
Symbologies 200 Gryphon™ I GD4100/GM4100 Optional A dd- On T imer This option sets the time the r eader will look for an add-on when an add- on fragment has been seen and optional add-ons are enabled. (Also see "Optional GS1 -128 Add-On Timer"on page 203 .
Add-Ons Product Reference Guide 201 Optional Add-On T imer — c ont . ENTER/EXIT PROGRAMMING MODE Optional Add-on Timer = 60ms Optional Add-on Timer = 70ms Optional Add-on Timer = 100ms Optional Add-.
Symbologies 202 Gryphon™ I GD4100/GM4100 Optional Add-On T imer — c ont. ENTER/EXIT PROGRAMMING MODE Optional Add-on Timer = 180ms Optional Add-on Timer = 200ms Optional Add-on Timer = 220ms Optio.
Add-Ons Product Reference Guide 203 Optional GS1-128 Add-On T imer This option sets the timer expiration value to read the added part after reading the linear EAN/ UPC part. For UPC/EAN add-ons othe r than those of that type, see "Optional Add-On Timer"on page 200 .
Symbologies 204 Gryphon™ I GD4100/GM4100 Optional GS1-128 A dd-On Time r — c ont . ENTER/EXIT PROGRAMMING MODE Optional GS1-128 Add-On Timer = 60ms Optional GS1-128 Add-On Timer = 70ms Optional GS.
Add-Ons Product Reference Guide 205 Optional GS1-128 A dd-On Time r — c ont . ENTER/EXIT PROGRAMMING MODE Optional GS1-128 Add-On Timer = 180ms Optional GS1-128 Add-O n Timer = 200ms Optional GS1-12.
Symbologies 206 Gryphon™ I GD4100/GM4100 P2 Add-Ons Minimum Reads This feature specifies the minimum number of ti mes a P2 add-on must be read before it is marked as valid and then combined with a b.
Add-Ons Product Reference Guide 207 P5 Add-Ons Minimum Reads This feature specifies the minimum number of ti mes a P5 add-on must be read before it is marked as valid and then combined with a base lab.
Symbologies 208 Gryphon™ I GD4100/GM4100 GS1-128 Add-Ons Minimum Reads This feature specifies the minimum number of time s an GS1-128 add- on must be read before it is marked as valid and then combi.
Code 39 Product Reference Guide 209 Co d e 3 9 The following options apply to the Code 39 symbology. C ode 39 Enable/Disable When disabled, the reader will not read Code 39 barcodes.
Symbologies 210 Gryphon™ I GD4100/GM4100 C ode 39 Check Character C alculation Enable this option t o enables/disables calcul atio n and verification of an optional Code 39 check character.
Code 39 Product Reference Guide 211 C ode 39 Check Character T ransmission Enable this option to trans mit the check character along with Code 39 barcode data.
Symbologies 212 Gryphon™ I GD4100/GM4100 C ode 39 F ull ASCII In Code 39 de coding, this en ables/disab les the translation of Code 39 characters to Code 39 full-ASCII characters.
Code 39 Product Reference Guide 213 C ode 39 Quiet Zones This feature specifies the number of quiet zone s for Cod e 39 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 time s the width of the narrowest bar or space in the label.
Symbologies 214 Gryphon™ I GD4100/GM4100 C ode 39 Minimum Reads This feature specifies the minimum number of consec utive times a Code 39 label must be decoded before it is accepted as good read.
Code 39 Product Reference Guide 215 C ode 39 Decoding L ev el Decoding Levels are u sed to configure a barc ode symbology decoder to be very aggressive to very conservative depending on a particul ar customer’s needs.
Symbologies 216 Gryphon™ I GD4100/GM4100 C ode 39 Decoding Le v el — cont . ENTER/EXIT PROGRAMMING MODE Code 39 Decodi ng Lev el = 1 Code 39 Decoding Level = 2 Code 39 Decodi ng Lev el = 3 Code 39.
Code 39 Product Reference Guide 217 Co d e 3 9 L e n g t h Co n t r o l This feature specifies either vari able length decoding or fixed le ngth decoding for the Code 39 symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Symbologies 218 Gryphon™ I GD4100/GM4100 C ode 39 Set Length 1 This feature specifies one of the barcode lengths for Code 39 L ength Control . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fi xe d L e n g t h Mode.
Code 39 Product Reference Guide 219 Code 39 Set L ength 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 39 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 220 Gryphon™ I GD4100/GM4100 C ode 39 Set Length 2 This feature specifies one of the barcode lengths for Code 39 L ength Control . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Len gt h Mode.
Code 39 Product Reference Guide 221 Code 39 Set L ength 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Co de 39L ength 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 222 Gryphon™ I GD4100/GM4100 C ode 39 Int erd igit Ratio This feature specifies the ratio between an intercharacter space and module for Code 39 labels.
Code 39 Product Reference Guide 223 Code 39 Interdigit R atio — cont. ENTER/EXIT PROGRAMMING MODE Code 39 Inte rdigit Ratio = 6 Code 39 Int erdigit Ratio = 7 Code 39 Inte rdigit Ratio = 8 Code 39 In.
Symbologies 224 Gryphon™ I GD4100/GM4100 C ode 39 Character C orrelation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Code 32 (Itali an Pharma ceutical Co de) Product Reference Guide 225 C ode 32 (Italian Pharmaceutical C o de) The following options apply to the Code 32 (Italian Pharmaceutical Code) symbology. C ode 32 Enable/Disable When disabled, the reader will not read Code 32 barcodes.
Symbologies 226 Gryphon™ I GD4100/GM4100 C ode 32 Check Character T ransmission Enable this option to trans mit the check character along with Code 32 barcode data.
Code 39 CIP (French Pharmaceutical) Product Reference Guide 227 C ode 39 CIP (F rench Pharmaceutical) The following options apply to the Code 39 CIP symbology. C ode 39 CIP Enable/Disable Enables/Disables ability of the read er to dec ode Code 39 CIP labels.
Symbologies 228 Gryphon™ I GD4100/GM4100 Co d e 1 2 8 The following options apply to the Cod e 128 symbolog y. C ode 128 Enable/Disable When disabled, the reade r will not read Code 128 barcodes.
Code 128 Product Reference Guide 229 C ode 128 Check Character T ransmission Enable this option to trans mit the check character along with Co de 128 barcode data.
Symbologies 230 Gryphon™ I GD4100/GM4100 C ode 128 Sub- Code Change T ransmission Enables/disables the transmission of “Sub-Cod e exchange” characters (NOT transmitted by standard decoding).
Code 128 Product Reference Guide 231 C ode 128 Quiet Zones This feature specifies the number of quiet zones for Code 128 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 time s the width of the narrowest bar or space in the label.
Symbologies 232 Gryphon™ I GD4100/GM4100 C ode 128 Minimum Reads This feature specifies the minimum number of consec utive times a Code 128 label must be decoded before it is accepted as good read.
Code 128 Product Reference Guide 233 C ode 128 Decoding L ev el Decoding Levels are u sed to configure a barc ode symbology decoder to be very aggressive to very conservative depending on a particul ar customer’s needs.
Symbologies 234 Gryphon™ I GD4100/GM4100 C ode 128 Decoding Le ve l — cont . ENTER/EXIT PROGRAMMING MODE Code 128 Decoding Lev el = 1 Code 128 Decoding Lev el = 2 Code 128 Decoding Lev el = 3 Code.
Code 128 Product Reference Guide 235 C ode 128 Length C ontrol This feature specifies either variable length deco ding or fixed length decoding for the Code 128 symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Symbologies 236 Gryphon™ I GD4100/GM4100 C ode 128 Set Length 1 This feature specifies one of the barcode lengths for Cod e 1 28 Le ngt h Co nt rol . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fi xe d L e n g t h Mode.
Code 128 Product Reference Guide 237 C ode 128 Set Length 1 — con t. ENTER/EXIT PROGRAMMING MODE Select Code 128 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 238 Gryphon™ I GD4100/GM4100 C ode 128 Set Length 2 This feature specifies one of the barcode lengths for Cod e 1 28 Le ngt h Co nt rol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Len gt h Mode.
Code 128 Product Reference Guide 239 C ode 128 Set Length 2 — con t. C ode 128 Character C orrela tion When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Symbologies 240 Gryphon™ I GD4100/GM4100 C ode 128 Stitching This option enables/disables stitching for Code 128 lab els. When parts of a Code 128 barcode are presented to the reader with this featu.
GS1-128 Product Reference Guide 241 GS1-128 The following options apply to the GS1-128 sy mbology. (Also known as USS-128, GS1-128, GTIN-128, UCC-12 8, EAN-128.) GS1-128 Enable This option enables/disables the ability of the re ader to translate GS1-128 labe ls to the GS1-128 data format.
Symbologies 242 Gryphon™ I GD4100/GM4100 C o de ISB T 128 The following options apply to the ISB T 128 symb ology. ISB T 128 C oncat enation Use this option to enable/disable ISBT128 concaten ation of 2 labels.
Code ISBT 128 Product Reference Guide 243 ISB T 128 F orce C oncatena tion When enabled, this feature forces concatenation for ISBT. ENTER/EXIT PROGRAMMING MODE ISBT 128 For ce C o ncatenation = Disable ISBT 1 28 Force Conc atenat ion = Ena ble NO TE This option is onl y valid when ISBT 128 Concatenation is enabled (see page 242).
Symbologies 244 Gryphon™ I GD4100/GM4100 ISB T 128 C oncat enation Mode Specifies the concatenation mode between Static and Dynamic. ENTER/EXIT PROGRAMMING MODE ISBT 128 Conca tenation Mode = Sta tic ISBT 128 Conca tenation Mode = Dynamic NO TE This option is onl y valid when ISBT 128 Concatenation is enabled (see page 242).
Code ISBT 128 Product Reference Guide 245 ISB T 128 Dynamic Conca tenation T imeout Specifies the timeout used by the IS BT 128 Dynamic Concatenation Mode.
Symbologies 246 Gryphon™ I GD4100/GM4100 Co d a b l o c k F The following options apply to the Codablock F symbology. C odablock F Enable/Disable Enables/Disables ability of reader to decode Codablock F labels.
Codablock F Product Reference Guide 247 C odablock F EAN Enable/Disable Enables/Disables the Codabloc k F EAN subtype (code with FNC1 in the first position).. ENTER/EXIT PROGRAMMING MODE Codablock F EAN = Disable Coda block F EAN = E nable Co d a b l o c k F A I M C h e c k Specifies if Check Digit calculation algorithm is AIM compliant or not.
Symbologies 248 Gryphon™ I GD4100/GM4100 Co d a b l o c k F L e n g t h Co n t r o l This feature specifies either variable length deco ding or fixed length de coding for the Codabl ock F symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Codablock F Product Reference Guide 249 C odablock F Set Length 1 This feature specifies one of the barcode lengths for Codablock F Length Contro l . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mod e, or the first fixed length if in Fix e d Len gt h Mode.
Symbologies 250 Gryphon™ I GD4100/GM4100 C odablock F Set Length 1 — c ont. ENTER/EXIT PROGRAMMING MODE Selec t Codablock F Le ngth 1 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
Codablock F Product Reference Guide 251 C odablock F Set Length 2 This feature specifies one of the barcode lengths for Codablock F Length Contro l . Length 2 is the maximum label length if in Va r i a b l e L e n g t h Mode, or the second fixed length if in Fi x e d Len gt h Mode.
Symbologies 252 Gryphon™ I GD4100/GM4100 C odablock F Set Length 2 — c ont. ENTER/EXIT PROGRAMMING MODE Selec t Codablock F Le ngth 2 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
Interleaved 2 of 5 (I 2 of 5) Product Reference Guide 253 Interlea ved 2 of 5 (I 2 of 5) The following options apply to the I 2 of 5 symbology. I 2 of 5 Enable/Disable When disabled, the reader will not read I 2 of 5 barcodes.
Symbologies 254 Gryphon™ I GD4100/GM4100 I 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional I 2 of 5 check character .
Interleaved 2 of 5 (I 2 of 5) Product Reference Guide 255 I 2 of 5 Check Character T ransmission Enable this option to trans mit the check character along with I 2 of 5 barcode data.
Symbologies 256 Gryphon™ I GD4100/GM4100 I 2 of 5 Minimum Reads This feature specifies the minimum number of consec utive times an I 2 of 5 label must be decoded before it is accepted as good read.
Interleaved 2 of 5 (I 2 of 5) Product Reference Guide 257 2 of 5 Decoding L ev el NO TE Decoding Levels are u sed to configure a barc ode symbology decoder to be very aggressive to very conservative depending on a particular customer’s ne eds.
Symbologies 258 Gryphon™ I GD4100/GM4100 2 of 5 Decoding Lev e l — cont . ENTER/EXIT PROGRAMMING MODE 2 of 5 Decoding Level = 1 2 of 5 Decoding Level = 2 2 of 5 Decoding Level = 3 2 of 5 Decoding .
Interleaved 2 of 5 (I 2 of 5) Product Reference Guide 259 I 2 of 5 Length C ontrol This feature specifies either vari able length decoding or fixed length decoding for the I 2 of 5 symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Symbologies 260 Gryphon™ I GD4100/GM4100 I 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for I 2 of 5 Le ngth Contr ol . Length 1 is the minimum label length if in V ariable Length Mode, or the first fixed length if in Fi xe d L e n g t h Mode.
Interleaved 2 of 5 (I 2 of 5) Product Reference Guide 261 I 2 of 5 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Selec t I 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 262 Gryphon™ I GD4100/GM4100 I 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for I 2 of 5 Le ngth Contr ol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Len gt h Mode.
Interleaved 2 of 5 (I 2 of 5) Product Reference Guide 263 I 2 of 5 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Selec t I 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 264 Gryphon™ I GD4100/GM4100 I 2 of 5 Character C orrela tion When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Follett 2 of 5 Product Reference Guide 265 F ollett 2 of 5 The following options apply to the Follett 2 of 5 symbology. F ollett 2 of 5 Enable/Disable Enables/Disables ability of imager t o decode Follett 2 of 5 labels.
Symbologies 266 Gryphon™ I GD4100/GM4100 Interlea ved 2 of 5 CIP HR The following options apply to the In terleaved 2 of 5 CIP HR symbology. Interlea ve d 2 of 5 CIP HR Enable/Disable Enables/Disables ability of reade r to decode Interleaved 2 of 5 CIP HR labels.
Standard 2 of 5 Product Reference Guide 267 Stan dard 2 of 5 The following options apply to the Standard 2 of 5 symbology. Standar d 2 of 5 Enable/Disable When disabled, the reade r will not read Standard 2 of 5 barcodes.
Symbologies 268 Gryphon™ I GD4100/GM4100 Standard 2 of 5 Check Char acter T ransmission This feature enables/disables transmission of an optional Standard 2 of 5 check character.
Standard 2 of 5 Product Reference Guide 269 Standar d 2 of 5 Minimum Reads This feature specifies the minimum number of co nsecutive times a Standard 2 of 5 label must be decoded before it is accepted as good read.
Symbologies 270 Gryphon™ I GD4100/GM4100 Standar d 2 of 5 Decoding L ev el NO TE Sta nda rd 2 of 5 Len gth Control This feature specifies either variable length deco ding or fixed length decoding for the Standard 2 of 5 symbology. Va r i a b l e L e n g t h .
Standard 2 of 5 Product Reference Guide 271 Standar d 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mode, or the first fixed length if in Fi x e d Len gt h Mode.
Symbologies 272 Gryphon™ I GD4100/GM4100 Standard 2 of 5 Set Length 1 — c ont. ENTER/EXIT PROGRAMMING MODE Selec t Standard 2 of 5 Le ngth 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. Y ou can then star t again at the beginning.
Standard 2 of 5 Product Reference Guide 273 Standar d 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control . Length 2 is the maximum label length if in Va r i a b l e L e n g t h M o de , o r t h e s ec on d fi xe d l en g th i f i n Fi x e d Len gt h Mode.
Symbologies 274 Gryphon™ I GD4100/GM4100 Standard 2 of 5 Set Length 2 — c ont. ENTER/EXIT PROGRAMMING MODE Selec t Standard 2 of 5 Le ngth 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. Y ou can then star t again at the beginning.
Standard 2 of 5 Product Reference Guide 275 Standar d 2 of 5 C h aracter Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Symbologies 276 Gryphon™ I GD4100/GM4100 Industrial 2 of 5 The following options apply to the Industrial 2 of 5 symbology. Industrial 2 of 5 Enable/Disable Enables/Disables ability of reader to decode Industrial 2 of 5 label s.
Industrial 2 of 5 Product Reference Guide 277 Industrial 2 of 5 Check Character T ransmission Enables/disables transmission of an Industrial 2 of 5 check character. Industrial 2 of 5 Length C ontrol This feature specifies either vari able length decodin g or fixed le ngth decoding for the Industrial 2 of 5 symbology.
Symbologies 278 Gryphon™ I GD4100/GM4100 Industrial 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Ind ustrial 2 of 5 Length Control . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mode, or the first fixed length if in Fi x e d Len gt h Mode.
Industrial 2 of 5 Product Reference Guide 279 Industrial 2 of 5 Set Length 1 — cont. Industrial 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Indust rial 2 of 5 Length Control .
Symbologies 280 Gryphon™ I GD4100/GM4100 Industrial 2 of 5 Set Length 2 — cont. 4. Scan the appropriate two digits from the keypad in the Keypad Appendix that repr esent the length setting which was determined in th e steps above. Y ou will hear a two-beep indi - cation after the last character .
Industrial 2 of 5 Product Reference Guide 281 Industrial 2 of 5 Minimum Reads This feature specifies the minimum number of cons ecutive times an Industrial 2 of 5 label must be decoded before it is accepted as good read.
Symbologies 282 Gryphon™ I GD4100/GM4100 Industrial 2 of 5 Stitching Enables/disables fixed length stitching for Industrial 2 of 5. ENTER/EXIT PROGRAMMING MODE Industrial 2 of 5 Stitching = Disable .
Industrial 2 of 5 Product Reference Guide 283 Industrial 2 of 5 Character C orrela tion Enable/disables character correlation for Industrial 2 of 5. ENTER/EXIT PROGRAMMING MODE Industrial 2 of 5 Chara.
Symbologies 284 Gryphon™ I GD4100/GM4100 Co d e I A T A The following options apply to the IATA symbology. IA T A Enable/Disable Enables/Disables the ability of th e reader to decode IATA labels.
Code IATA Product Reference Guide 285 IA T A Check Character T ransmission Enables/Disables calculation and verificati on of an optional Industrial 2 of 5 check character.
Symbologies 286 Gryphon™ I GD4100/GM4100 Datalogic 2 of 5 The following options apply to the Datalogic 2 of 5 symbology. Datalogic 2 of 5 Enable/Disable When disabled, the reader will not read Datalogic 2 of 5 barcodes.
Datalogic 2 of 5 Product Reference Guide 287 Datalogic 2 of 5 Minimum Reads This feature specifies the minimum number of co nsecutive times an Datalogic 2 of 5 label must be decoded before it is accepted as good read.
Symbologies 288 Gryphon™ I GD4100/GM4100 Datalogic 2 of 5 L ength C o ntr ol This feature specifies either vari able length decoding or fixed le ngth decoding for the Datalogic 2 of 5 symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Datalogic 2 of 5 Product Reference Guide 289 Datalogic 2 of 5 Set Length 1 This feature specifies one of the b arcode lengths for Datalogic 2 of 5 Length C ontrol . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mode, or the first fixed length if in Fi x e d Len gt h Mode.
Symbologies 290 Gryphon™ I GD4100/GM4100 Datalogic 2 of 5 Set Length 1 — c ont . ENTER/EXIT PROGRAMMING MODE Selec t Datalogic 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. Y ou can then star t again at the beginning.
Datalogic 2 of 5 Product Reference Guide 291 Datalogic 2 of 5 Set Length 2 This feature specifies one of the b arcode lengths for Datalogic 2 of 5 Length C ontrol . Length 2 is the maximum label length if in Va r i a b l e L e n g t h M o de , o r t h e s ec on d fi xe d l en g th i f i n Fi x e d Len gt h Mode.
Symbologies 292 Gryphon™ I GD4100/GM4100 Datalogic 2 of 5 Set Length 2 — c ont . ENTER/EXIT PROGRAMMING MODE Selec t Datalogic 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. Y ou can then star t again at the beginning.
Datalogic 2 of 5 Product Reference Guide 293 Datalogic 2 of 5 Char acter Correla tion When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Symbologies 294 Gryphon™ I GD4100/GM4100 Co d a b a r The following options apply to the Codabar symbology. C odabar Enable/Disable When disabled, the reade r will not read Codabar barcodes.
Codabar Product Reference Guide 295 C odabar Check Character Calculation Enable this option to enables/disables calcul atio n and verification of an optional Codabar check character.
Symbologies 296 Gryphon™ I GD4100/GM4100 C odabar Check Character T ransmission Enable this option to trans mit the check character along with Codabar barcode data.
Codabar Product Reference Guide 297 C odabar Star t/Stop Charac ter Set This option specifies the format of tr ansmitted Codabar start/stop characters ENTER/EXIT PROGRAMMING MODE Codabar Check Character Set = ABCD/TN*E Codaba r Check Char acter Set = ABCD/ABCD Codabar Check Charac ter Set = abcd/tn *e Codaba r Check Character Set = abcd/abcd .
Symbologies 298 Gryphon™ I GD4100/GM4100 C odabar Star t/Stop Charac ter Match When enabled, this option requires that start and stop characters match ENTER/EXIT PROGRAMMING MODE Codabar Start /Stop Character Match = Do n’ t Require Match Codabar S tart/Stop Character Mat ch = Requir e Mat ch .
Codabar Product Reference Guide 299 C odabar Quiet Zones This feature specifies the number of quiet zone s for Codabar labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 time s the width of the narrowest bar or space in the label.
Symbologies 300 Gryphon™ I GD4100/GM4100 C odabar Minimum Reads This feature specifies the minimum number of consec utive times a Codabar label must be decoded before it is accepted as good read.
Codabar Product Reference Guide 301 C odabar Decoding L ev el Decoding Levels are u sed to configure a barc ode symbology decoder to be very aggressive to very conservative, depending on a particular customer’s needs.
Symbologies 302 Gryphon™ I GD4100/GM4100 Co d a b a r L e n g t h Co n t ro l This feature specifies either variable length decoding or fixed length decoding for the Codabar symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Codabar Product Reference Guide 303 C odabar Set Length 1 This feature specifies one of the barcode lengths for Codabar Length Control . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fi xe d L e n g t h Mode.
Symbologies 304 Gryphon™ I GD4100/GM4100 C odabar Set Length 1 — cont . ENTER/EXIT PROGRAMMING MODE Select Codaba r L ength 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. Y ou can then star t again at the beginning.
Codabar Product Reference Guide 305 C odabar Set Length 2 This feature specifies one of the barcode lengths for Codabar Length Control . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Len gt h Mode.
Symbologies 306 Gryphon™ I GD4100/GM4100 C odabar Set Length 2 — cont . ENTER/EXIT PROGRAMMING MODE Select Codaba r L ength 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. Y ou can then star t again at the beginning.
Codabar Product Reference Guide 307 C odabar Int erdigit Ratio This feature specifies the ratio between an inte rcharacter space and module for Codabar labels.
Symbologies 308 Gryphon™ I GD4100/GM4100 Codabar Interdigit Ratio — cont. ENTER/EXIT PROGRAMMING MODE Codabar Inte rdigit Ratio = 6 Coda bar Int erd igit Rati o = 7 Codabar Inte rdigit Ratio = 8 C.
Codabar Product Reference Guide 309 C odabar Character Corr elation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
Symbologies 310 Gryphon™ I GD4100/GM4100 ABC C odabar The following options apply to the ABC Codabar symbology. ABC C odabar Enable/Disable Enables/Disables ability of reader to decode ABC Codabar labels.
ABC Codabar Product Reference Guide 311 A B C Co d a b a r D y n a m i c Co n c a t e n a t i o n Ti m e o u t Specifies the timeout in 10-millisecond ticks used by the ABC Codabar Dynamic Concatenation Mode.
Symbologies 312 Gryphon™ I GD4100/GM4100 A B C Co d a b a r For c e Co n c a t e n at i o n Forces labels starting or ending with D to be concatenated.
Code 11 Product Reference Guide 313 Co d e 1 1 The following options apply to the Code 11 symbology. C ode 11 Enable/Disable When disabled, the reader will not read Code 11 barcodes.
Symbologies 314 Gryphon™ I GD4100/GM4100 C ode 11 Check Character C alculation This option enables/disables calculation and veri fication of optional Code 11 check character.
Code 11 Product Reference Guide 315 C ode 11 Check Character T ransmission This feature enables/disables transmission of an optional Code 11 check character.
Symbologies 316 Gryphon™ I GD4100/GM4100 C ode 11 Minimum Reads This feature specifies the minimum number of consec utive times a Code 11 label must be decoded before it is accepted as good read.
Code 11 Product Reference Guide 317 Co d e 1 1 L e n g t h Co n t r o l This feature specifies either vari able length decoding or fixed le ngth decoding for the Code 11 symbology. Va r i a b l e L e n g t h . For variable length decoding, a minimum and maximum length may be set.
Symbologies 318 Gryphon™ I GD4100/GM4100 C ode 11 Set Length 1 This feature specifies one of the barcode lengths for Code 11 L ength Control . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fi xe d L e n g t h Mode.
Code 11 Product Reference Guide 319 Code 11 Set L ength 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 11 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 320 Gryphon™ I GD4100/GM4100 C ode 11 Set Length 2 This feature specifies one of the barcode lengths for Code 11 L ength Control . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Len gt h Mode.
Code 11 Product Reference Guide 321 Code 11 Set L ength 2 — cont. ENTER/EXIT PROGRAMMING MODE Selec t Code 11 L ength 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string. Y ou can then start aga in at the beginning .
Symbologies 322 Gryphon™ I GD4100/GM4100 C ode 11 Int erd igit Ratio This feature specifies the ratio between an intercharacter space and module for Code 11 labels.
Code 11 Product Reference Guide 323 Code 11 Interdigit R atio — cont. ENTER/EXIT PROGRAMMING MODE Code 11 Inte rdigit Ratio = 6 Code 11 Int erdigit Ratio = 7 Code 11 Inte rdigit Ratio = 8 Code 11 In.
Symbologies 324 Gryphon™ I GD4100/GM4100 C ode 11 Decoding L ev el Decoding Levels are used to configure a barcod e symbology decoder to be very aggressive to very conservative depending on a particul ar customer’s needs.
Code 11 Product Reference Guide 325 C ode 11 Decoding Le v el — cont . ENTER/EXIT PROGRAMMING MODE Codabar Decoding Level = 1 Coda bar Decod ing L eve l = 2 Codabar Decoding Level = 3 Coda bar Decod.
Symbologies 326 Gryphon™ I GD4100/GM4100 C ode 11 Character C orrelation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help th e scanner read labels th at have some spots and/ or voids.
GS1 DataBar™ Omnidirectional Product Reference Guide 327 GS1 DataBar™ Omnidir ectional The following options apply to the GS1 Da taBar™ Omnidirectional (formerly RSS-14) symbology. GS1 DataBar™ Omnidirectional Enable/Disable When disabled, the reade r will not read GS1 DataBar™ Omnidirectional barcodes.
Symbologies 328 Gryphon™ I GD4100/GM4100 GS1 DataBar™ Omnidirectional Minimum Reads This feature specifies the minimum number of consec utive times a GS1 DataBar™ Omnidirectional label must be d.
GS1 DataBar™ Expanded Product Reference Guide 329 GS1 DataBar™ Expanded The following options apply to the GS1 Da taBar™ Expanded (formerly RSS Expanded) symbology. GS1 DataBar™ Expanded Enable/Disable When disabled, the reade r will not re ad GS1 DataBar™ Expanded barcodes.
Symbologies 330 Gryphon™ I GD4100/GM4100 GS1 DataBar™ Expanded Minimum Reads This feature specifies the minimum number of consec utive times a GS1 DataBar™ Expanded label must be decoded before .
GS1 DataBar™ Expanded Product Reference Guide 331 GS1 DataBar™ Expanded Le ngth C ontr ol This feature specifies either va riable length decoding or fixe d length decoding for the GS1 DataBar™ Expanded symbology. Va r i a b l e L e n g t h . For variable-length decoding, a minimum length may be set.
Symbologies 332 Gryphon™ I GD4100/GM4100 GS1 DataBar™ Expanded Set Length 1 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control . Length 1 is the minimum label length if in Va r i a b l e L e n g t h Mode, or the first fixed length if in F ixed Length Mode.
GS1 DataBar™ Expanded Product Reference Guide 333 GS1 DataBar™ Expanded Set Length 1 — c ont. ENTER/EXIT PROGRAMMING MODE Select GS1 DataBar™ Expanded Set L ength 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string.
Symbologies 334 Gryphon™ I GD4100/GM4100 GS1 DataBar™ Expanded Set Length 2 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control . Length 2 is the maximum label length if in Va r i a b l e L e n g t h Mode, or the second fix ed length if in F ixed Length Mode.
GS1 DataBar™ Expanded Product Reference Guide 335 GS1 DataBar™ Expanded Set Length 2 — c ont. ENTER/EXIT PROGRAMMING MODE Select GS1 DataBar™ Expanded Set L ength 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the en try string.
Symbologies 336 Gryphon™ I GD4100/GM4100 GS1 DataBar™ Limited The following options apply to the GS1 DataBar™ Limited (formerly RSS Limited) symbology. GS1 DataBar™ Limited Enable/Disable When disabled, the reade r will not read GS1 DataBar™ Limited barcodes.
GS1 DataBar™ Limited Product Reference Guide 337 GS1 DataBar™ Limited Minimum Reads This feature specifies the minimum number of consecutive times a GS1 DataBar™ Limited label must be decoded be.
Symbologies 338 Gryphon™ I GD4100/GM4100 Co d e 9 3 The following options apply to the Code 93 symbology. C ode 93 Enable/Disable Enables/Disables ability of reader to decode Code 93 labels.
Code 93 Product Reference Guide 339 C ode 93 Check Character C alculation Enables/disables calculat ion and verification of an optional Code 93 check character.
Symbologies 340 Gryphon™ I GD4100/GM4100 C ode 93 Check Character T ransmission Enables/disables transmission of an optional Code 93 check character.
Code 93 Product Reference Guide 341 C ode 93 Set Length 1 This feature specifies one of the barcode lengths for Code 93 L ength Control . Length 1 is the minimum label length if in V a riable Length Mode, or the first fixed length if in Fi xe d L e n g t h Mode.
Symbologies 342 Gryphon™ I GD4100/GM4100 Code 93 Set L ength 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 93 Set Length 1 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
Code 93 Product Reference Guide 343 C ode 93 Set Length 2 This feature specifies one of the barcode lengths for Code 93 L ength Control . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi xe d Len gt h Mode.
Symbologies 344 Gryphon™ I GD4100/GM4100 Code 93 Set L ength 2 — cont. ENTER/EXIT PROGRAMMING MODE Selec t Code 93 L ength 2 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
Code 93 Product Reference Guide 345 C ode 93 Minimum Reads This feature specifies the minimum number of consecutive times a Code 93 label must be decoded before it is accepted as good read.
Symbologies 346 Gryphon™ I GD4100/GM4100 C ode 93 Decoding L ev el Specifies the decoding level for Code 93. Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending o n a particular customer’s needs.
Code 93 Product Reference Guide 347 C ode 93 Decoding Lev el — cont. ENTER/EXIT PROGRAMMING MODE Code 93 Decoding Level = 4 Code 93 Decodi ng Lev el = 5.
Symbologies 348 Gryphon™ I GD4100/GM4100 C ode 93 Quiet Zones Enables/disables quiet zones for Code 93. ENTER/EXIT PROGRAMMING MODE Cod e 9 3 Qu i et Zon e s = No Q ui et Zo ne s C ode 93 Quie t Z o.
Code 93 Product Reference Guide 349 C ode 93 Stitching Disable/enable fixed or variable length stitching for Code 93. ENTER/EXIT PROGRAMMING MODE Code 93 S titchin g = Disable Code 93 Stitching = Enable C ode 93 Character C orrelation Enables/disables Characte r Correlation for Code 93.
Symbologies 350 Gryphon™ I GD4100/GM4100 MSI The following options apply to the MSI symbology. MSI Enable/Disable Enables/Disables ability of re ader to decode MSI labels.
MSI Product Reference Guide 351 MSI Check Character Calculation Enables/Disables calculation and verificat ion of an optional MSI check character. ENTER/EXIT PROGRAMMING MODE MSI Ch eck Ch aracte r Ca.
Symbologies 352 Gryphon™ I GD4100/GM4100 MSI Check Character T ransmission Enables/disables transm ission of an MSI check character. ENTER/EXIT PROGRAMMING MODE MSI Check Character T ransmission = D.
MSI Product Reference Guide 353 MSI Set Length 1 This feature specifies one of the barcode lengths for MSI Length C ontrol . Length 1 is the minimum label length if in V ariable Length Mode, or the first fixed length if in Fixe d Le ng th Mode. Length includes the barcode’s data characters only.
Symbologies 354 Gryphon™ I GD4100/GM4100 MSI Set Length 1 — cont . ENTER/EXIT PROGRAMMING MODE Select MSI Set L ength 1 Set ting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
MSI Product Reference Guide 355 MSI Set Length 2 This feature specifies one of the barcode lengths for MSI Length C ontrol . Length 2 is the maximum label length if in V ariable Length Mode, or the second fixed length if in Fi x e d Le ng th Mode. Length includes the barcode’s check, data, and full-ASCII shift charac - ters.
Symbologies 356 Gryphon™ I GD4100/GM4100 MSI Set Length 2 — cont . ENTER/EXIT PROGRAMMING MODE Select MSI Length 2 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
MSI Product Reference Guide 357 MSI Minimum Reads This feature specifies the mini mum number of consecutive tim es an MSI label must be decoded before it is accepted as good read.
Symbologies 358 Gryphon™ I GD4100/GM4100 MSI Decoding L ev el Specifies the decoding level for MSI. Decodi ng Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending o n a particular customer’s needs.
MSI Product Reference Guide 359 MSI Stitching Enables/disables fixed length stitching for MSI. ENTER/EXIT PROGRAMMING MODE MSI Stitching = Disable MSI Stitching = Ena ble MSI Decoding L evel — c ont .
Symbologies 360 Gryphon™ I GD4100/GM4100 MSI Character Corr elation Enables/disables Character Correlation for MSI. ENTER/EXIT PROGRAMMING MODE MSI Character C orrel ation = Disable MSI Character Co.
Plessey Product Reference Guide 361 Plessey The following options apply to the Plessey symbology. Plessey Enable/Disable Enables/Disables ability of read er to decode Plessey labels.
Symbologies 362 Gryphon™ I GD4100/GM4100 Plessey Check Char acter Calcula tion Enables/Disables calculation and verificatio n of an optional Plessey check character. ENTER/EXIT PROGRAMMING MODE Plesse y Chec k Charac ter Calcu lation = Dis able Plessey Check Character Calculation = Enable Plessey std.
Plessey Product Reference Guide 363 Plessey Check Char acter T ransmission Enables/disables transmission of an MSI check character. ENTER/EXIT PROGRAMMING MODE Plessey Check Character T ransmission = .
Symbologies 364 Gryphon™ I GD4100/GM4100 Plessey Set Length 1 This feature specifies one of the barcode lengths for Plessey Length Contr ol . Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode.
Plessey Product Reference Guide 365 Plessey Set Length 1 — cont . ENTER/EXIT PROGRAMMING MODE Select Plessey Set L ength 1 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
Symbologies 366 Gryphon™ I GD4100/GM4100 Plessey Set Length 2 This feature specifies one of the barcode lengths for Plessey Length Contr ol . Length 2 is the maximum label length if in Variable Length Mode, or th e second fixed length if in Fixed Length Mode.
Plessey Product Reference Guide 367 Plessey Set Length 2 — cont . ENTER/EXIT PROGRAMMING MODE Select Plessey Length 2 Setting Make a mistak e? Scan the CANCEL barcode to abor t and not sav e the entr y str ing. Y ou can then star t again at the beginning.
Symbologies 368 Gryphon™ I GD4100/GM4100 Plessey Minimum Reads This feature specifies the minimum number of conse cutive times a Plessey label must be decoded before it is accepted as good read.
Plessey Product Reference Guide 369 Plessey Dec oding Le v el Specifies the decoding level for Plessey. Deco ding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depend ing on a particular customer’s needs.
Symbologies 370 Gryphon™ I GD4100/GM4100 Plessey Stit ching Enables/disables fixed length stitching for Plessey. ENTER/EXIT PROGRAMMING MODE Plessey Stitching = Disable Plessey Sti tching = Enab le Plessey Decoding Le vel — c ont.
Plessey Product Reference Guide 371 Plessey Character C orrela tion Enables/disables Character Correlation for Plessey. ENTER/EXIT PROGRAMMING MODE Plessey Chara cter Correlation = Disable Plessey Cha.
Symbologies 372 Gryphon™ I GD4100/GM4100 Co d e 4 The following options apply to the Cod e 4 symbolog y. C ode 4 Enable/Disable Enables/Disables ability of imager t o decode Code 4 labels.
Code 4 Product Reference Guide 373 C ode 4 He x to Decimal C on v ersion This feature enables/disables the conver sion of hexidecimal label data to decimal label data.
Symbologies 374 Gryphon™ I GD4100/GM4100 Co d e 5 The following options apply to the Cod e 5 symbolog y. C ode 5 Enable/Disable Enables/Disables ability of imager t o decode Code 5 labels.
Code 5 Product Reference Guide 375 C ode 5 He x to Decimal C on v ersion This feature enables/disables the conver sion of hexidecimal label data to decimal label data.
Symbologies 376 Gryphon™ I GD4100/GM4100 C o de 4 and C ode 5 C ommon Configur ation Items The following options apply to both Code 4 and Code 5 symbologies. C ode 4 and 5 Decoding L ev el Decoding Levels are used to configure a barcod e symbology decoder to be very aggressive to very conservative depending on a particul ar customer’s needs.
Code 4 and Code 5 Commo n Configuration Ite ms Product Reference Guide 377 Code 4 and 5 Dec oding Lev el — cont. ENTER/EXIT PROGRAMMING MODE Code 4 and Code 5 Decoding Level = 1 Code 4 an d Code 5 D.
Symbologies 378 Gryphon™ I GD4100/GM4100 C ode 4 and C ode 5 Minimum Reads This feature specifies the minimum number of co nsecutive times a Cod e 4 or Code 5 label must be decoded before it is accepted as good read.
Pr oduct Refer ence Guide 379 Chapter 14 Message F ormatting Message F ormatting A message from the Host to the base must follow these rules: • If Address stamping options or address delimi ter ar e enabled on the base, the H ost replay must have address field and delimiter too.
Message Formatting 380 Gryphon™ I GD4100/GM4100 • If you want to control the Scanner's beeper fr om the host, you will also probably want to disable the good transmission beep that is em itted when the code is received from the cra - dle. (See RF B eeper F eatures on page 154 ).
Message Formatting Product Reference Guide 381 Clearing Display LED and Beeper Con trol The LED control escape sequences are intended to activate the LEDs for short periods of time and can be used in combination with the Beeper . The LED and Beeper will be controlled by the system after the entire comman d sequence is interpreted.
Message Formatting 382 Gryphon™ I GD4100/GM4100 Messages from Scanner C ommand K eys T h e G r y p h o n ™ I s e r i e s s ca n n e r s w i t h d i s p l a y h a v e 3 c o m m a n d k e y s t h a t c a n e a c h b e a s s o ci a t e d with a character to send to the host.
Pr oduct Reference Guide 383 Appendix A T echnical Specifica tions Table 47 contains Physical and Perf ormance Characteristics, User Environment and Regulatory information.
Technical Specifications 384 Gryphon™ I GD4100/GM4100 Operating autonom y (continuous r eading) 50,000 re ads (typical) Performance Charac teristics Light Source Dual LEDs Roll ( Tilt) T olerance ± 35° from normal Pitch T olerance ± 65° Skew ( Y aw) T olerance ± 65° Field of V iew 10” (25.
Technical Specifications P roduct Reference Guide 385 (a) T ypical input cur ren t measure d under factory default configurat ion. (b) See "Inter face Selec tion"on page 67 for a listing of avai lable interface sets by model type. (c) Charge Times are much lower when battery is within daily typic al operating condition.
Technical Specifications 386 Gryphon™ I GD4100/GM4100 Standard C able P inouts Fig u re 2 0 and Table 48 provide standard pi nout informatio n for the Base Station’s interface cable.
Pr oduct Reference Guide 387 Appendix B LED and Beeper Indications The reader’s beeper sounds and its LED illuminate s to indicate various functions or errors on the reader. An optional “Green Sp ot” also performs useful functions. The tables below list these indications.
LED and Beeper Indications 388 Gryphon™ I GD4100/GM4100 Ta b l e 50 Programming Mode - The following indications ONL Y o ccur when the reader is in Programming Mode. Label Program - ming Mode Entry A va lid programming label has been sc anned. LED blinks continuously Reader sounds four low fr eq uenc y beeps.
LED and Beeper Indications P roduct Reference Guide 389 Base Station Indica tions INDICA TION LEDS P ower-up C omplete Ye l l o w L E D o n Reader Disabled by the HOST or the commun ica - tion with HO.
LED and Beeper Indications 390 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Reference Guide 391 Appendix C Standar d Defaults The most common configuration settings are listed in the “Default” column of the table below. Page references are also provid ed for feature d escriptions and programming barcodes for each parameter.
Standard Defaults 392 Gryphon™ I GD4100/GM4100 Flash O f f Tim e 600 ms 57 Green Spot Dura tion 300 ms 59 Display - Fo n t S i z e Small 60 - Backlight Off 61 - Display Mode Loc a l Ec h o m od e 62.
Standard Defaults P roduct Reference Guide 393 Caps Lock S tate Caps Lock OFF 102 Numlock Numlock Key Unchanged 103 Send Contr ol Characters Disable 104 We d g e Q u i e t I n t e r v a l 100 ms 105 I.
Standard Defaults 394 Gryphon™ I GD4100/GM4100 Automa tic C onfiguration Update Enable 162 Pow e r d o w n T i m e o u t 60 minutes (1 hour) 164 Bat ch Mode Disable 166 Source Radio Address T ransmi.
Standard Defaults P roduct Reference Guide 395 EAN-13 ISBN Co nv ersion Disable 187 EAN 13 Minimum Reads 1 188 ISSN ISSN Enable/Disable Disable 189 EAN 8 EAN 8 Enable/Disable Enable 190 EAN 8 Check Ch.
Standard Defaults 396 Gryphon™ I GD4100/GM4100 Cod e 3 9 Le n g th Co n tro l Va r i a b l e 217 Code 39 Set Length 1 2 218 Code 39 Set Length 2 50 220 Code 39 Int erdigit Ratio 4 222 Cod e 3 9 Ch a.
Standard Defaults P roduct Reference Guide 397 ISBT 128 ISBT 128 Concatenati on Disable 242 ISBT 128 Force Concatenation Disable 243 ISBT 128 Concatenati on Mod e Static 244 ISBT 128 D y namic Concate.
Standard Defaults 398 Gryphon™ I GD4100/GM4100 Standard 2 of 5 Enable/Disable Disable 267 Standard 2 of 5 Check Character Calcula - tion Disable 267 Standard 2 of 5 Check Character T rans - mission .
Standard Defaults P roduct Reference Guide 399 Datalogic 2 of 5 Dec oding L evel 3 287 Datalogic 2 of 5 L ength Control Va r i a b l e 288 Datalogic 2 of 5 Set L ength 1 6 characters 289 Datalogic 2 o.
Standard Defaults 400 Gryphon™ I GD4100/GM4100 Code 11 Check Character Calcula tion Check C and K 314 Code 11 Check Character T ransmission Send 315 Code 11 Minimum Read s 1 316 Cod e 1 1 Le n g th .
Standard Defaults P roduct Reference Guide 401 Code 93 Check Character Calculation Enable Check C and K 339 Code 93 Check Character T ransmission Enable 340 Cod e 9 3 Len g t h Con t ro l Va r i a b l.
Standard Defaults 402 Gryphon™ I GD4100/GM4100 Plessey Stitching Disable 370 Plessey Character Corr elation Disable 371 Code 4 Cod e 4 E na b l e/ D i sa b le Disable 372 Code 4 Check Character T ra.
Pr oduct Reference Guide 403 Appendix D Sa m p l e B ar c od e s The sample barcodes in this appendix are typical representations for their symbology types.
Sample Barcodes 404 Gryphon™ I GD4100/GM4100 Sample Barc odes — continued Code 32 Codabar Code 93 Code 1 1 A 0200 96020.
Sample Barcodes P roduct Reference Guide 405 GS1 DataBar™ (RSS) NO TE GS1 DataBar™-14 GS1 DataBar™ variants must be enab led to r ead the barc odes below (see GS1 DataBar™ Omnidirectional on page 327 ).
Sample Barcodes 406 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Reference Guide 407 Appendix E Ke y p a d Use the barcodes in this appendix to enter numbers as you would select digits /characters from a keypad.
Keypad 408 Gryphon™ I GD4100/GM4100 6 7 8 9.
Keypad P roduct Reference Guide 409 A B C D E F.
Keypad 410 Gryphon™ I GD4100/GM4100 NO TES.
Pr oduct Refer ence Guide 411 Ap pe ndix F Sc ancode T ables C ontrol Char ac ter Emula tion Control character emulation selects from different scancode tables as listed in this appendix. Each of the control character sets below are detail ed by interface type in the tables.
412 Gryphon™ I GD4100/GM4100 Inter face T ype PC A T PS/2 or USB-K eyboard T able 52. Scancode S et When Con trol Character is 00 or 01 Extended characters (sk y blue) are sent th r ough dedicat ed keys ( when a vailable i n the selected country mode) or by using an Al t Mode sequ ence.
Pr oduct Reference Guide 413 Inter face T ype P C A T PS/2 or USB-Keyboar d — cont. T able 53. Scancode S et When Con trol Character is 02.
414 Gryphon™ I GD4100/GM4100 Inter face type PC A T PS/2 A lt Mode or USB-K e yboard A lt Mode T able 54. Scancode S et When Con trol Character is 00 or 01.
Pr oduct Reference Guide 415 Inter face typ e PC A T PS/2 Alt Mode or USB -Keyboar d Alt Mode — cont . T able 55. Scancode S et When Con trol Character is 02.
416 Gryphon™ I GD4100/GM4100 Digital Inter face T able 56. Scancode S et When Con trol Character is 00 or 01.
Pr oduct Reference Guide 417 Digital Interface — c ont . T able 57. Scancode S et When Con trol Character is 02.
418 Gryphon™ I GD4100/GM4100 IBM31xx 102-ke y T able 58. Scancode S et When Con trol Character is 00 or 01.
Pr oduct Reference Guide 419 IBM31xx 102-k ey — con t. T able 59. Scancode S et When Con trol Character is 02.
420 Gryphon™ I GD4100/GM4100 IBM XT T able 60. Scancode S et When Con trol Character is 00 or 01.
Pr oduct Reference Guide 421 IBM XT — cont. T able 61. Scancode S et When Con trol Character is 02.
422 Gryphon™ I GD4100/GM4100 Microsof t Windo w s C odepage 1252 Windows-1252 is a character encoding of the Latin alphabet, used by default in the lega cy components of Microsoft Windows in En glish and some other Western languages.
Prod uc t R efe re nce G ui de 423 Inde x B barcodes cancel 407 numeric barcodes 407 RS-232 bau d r a te 111 RS-232 parameters p a rity 102 , 265 , 372 , 374 , 377 battery WARNINGS 14 Beeper Pitch, Go.
424 Gryphon™ I GD4100/GM4100 Index P Performance Characteristics 3 8 4 Physical Characteristics 3 8 3 Pitch – Good Read, Beeper 41 , 42 Polarity (wand) 124 Prefix/Suffix 130 Product Specifications.
ASCII Char t ASCII Char . Hex No . ASCII Char . Hex No . ASCII Char . Hex No . ASCII Char . He x No . NUL SOH STX ETX EO T ENQ AC K BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM S.
Datalogic Scanning, Inc. 959 T err y Street Eugene, OR 97402 USA T elephone: (541) 683-5700 F ax: (541) 345-7140 ww w .scanning.datalogic.com Austr alia Datalogic Scanning Pt y Lt d T elephone: [61] (2) 9870 3200 australia.scanning@datalogic .com F rance and Benelux Datalogic Scanning Sarl T elephone: [33].
Een belangrijk punt na aankoop van elk apparaat Datalogic GD4130-WH (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Datalogic GD4130-WH heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Datalogic GD4130-WH vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Datalogic GD4130-WH leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Datalogic GD4130-WH krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Datalogic GD4130-WH bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Datalogic GD4130-WH kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Datalogic GD4130-WH . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
