Gebruiksaanwijzing /service van het product 315.21234 van de fabrikant Craftsman
Ga naar pagina of 42
10 in. COMPOUND MITER SA W DOUBLE INSULA TED Model Nos. 315.212340 315.242340 OPERA TOR'S MANUAL WARNING : T o reduce the risk of injury , the user must read and understand the operator’ s manual before using this pr oduct. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co.
2 3 T ABLE OF CONTENTS n W arranty ............................................................................................................................................................................2 n Introduction ...........................
2 3 GENERAL SAFETY RULES WARNING: Read and understand all instruc- tions. Failure to follow all instructions listed below , may result in electric shock, fir e and/or serious personal injury . READ ALL INSTRUCTIONS n KNOW YOUR POWER TOOL. Read the operator's manual carefully .
4 5 GENERAL SAFETY RULES n INSPECT TOOL CORDS PERIODICALL Y . If damaged, have repair ed by a qualified service technician at an authorized service facility . The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-ground- ing conductor .
4 5 SPECIFIC SAFETY RULES n NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area. n NEVER reach behind, under , or within three inches of the blade and its cutting path with your hands and fingers for any reason.
6 7 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer .
6 7 SYMBOLS SERVICE Servicing requir es extreme car e and knowledge and should be performed only by a qualified service tech- nician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for r epair . When servicing, use only identical replacement parts.
8 9 ELECTRICAL EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sur e to use an extension cord that has the capacity to handle the current the tool will draw . An undersized cord will cause a dr op in line voltage, resulting in overheating and loss of power .
8 9 GLOSSAR Y OF TERMS Non-Through Cuts Any cutting operation where the blade does not extend completely through the thickness of the workpiece. Push Blocks and Push Sticks Devices used to feed the workpiece through the saw blade during cutting operations.
10 11 PRODUCT SPECIFICA TIONS Blade Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 in. Blade Arbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5/8 in. No Load Speed . . . . . . . . . . . . . . . . . . . . . . . .
10 11 SPINDLE LOCK BUTTON SWITCH TRIGGER Fig. 3 FEA TURES P ADLOCK SWITCH TRIGGER Fig. 4 Fig. 2 KNOW YOUR COMPOUND MITER SA W See Figure 1. Before attempting to use this pr oduct, familiarize yourself with all operating features and safety rules. 15 AMP MOTOR Y our saw has a powerful 15 amp motor with sufficient power to handle tough cutting jobs.
12 13 FEA TURES POSITIVE STOPS ON MITER T ABLE Positive stops have been provided at 0°, 15°, 22-1/2°, 30°, and 45° on both the left and right side of the miter table. BEVEL LOCK KNOB The bevel lock knob securely locks your compound miter saw at desired bevel angles.
12 13 The following tools (not included) are needed for checking adjustments of your saw or for installing the blade: TOOLS NEEDED COMBINA TION SQUARE FRAMING SQUARE COMBINA TION WRENCH (2) 10 mm,14 mm Fig.
14 15 LOOSE P AR TS LIST Fig. 7 WARNING: The use of attachments or accessories not listed might be hazar dous and could cause serious personal injury .
14 15 UNP ACKING This product r equires assembly . n Carefully lift saw fr om the carton by the carrying handle and the saw base, and place it on a level work surface. NOTE: This saw is heavy . T o avoid back injury , lift with your legs, not your back, and get help when needed.
16 17 ASSEMBL Y DUST GUIDE EXHAUST PORT DUST GUIDE See Figure 10. T o install the dust guide, place the end marked INSERT over the exhaust port in the upper blade guard. T ur n the guide so that the open end is facing down or toward the rear of the saw .
16 17 Fig. 12 SA W VIEWED FROM BOTTOM MITER SA W BASE T ABLE EXTENSION ASSEMBL Y T ABLE EXTENSIONS See Figures 12 - 13. If you plan to use the stop block, slide the stop block on the back arm of the desired table extension first. T o install table extensions, insert the ends of extensions into the holes in the sides of the base.
18 19 TO INST ALL BLADE See Figures 15 - 17. WARNING: A 10 in. blade is the maximum blade capacity of the saw . Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle.
18 19 Fig. 16 ASSEMBL Y Fig. 17 SPINDLE LOCK BUTTON n Remove the laser guide or outer blade washer . Do not remove inner blade washer . n Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade. WARNING: If inner blade washer has been removed, r eplace it before placing blade on spindle.
20 21 ASSEMBL Y MOUNTING THE LASER GUIDE See Figure 18. n Unplug the saw . See "T o Install Blade" on page 18 in the Assembly section of this operator's manual. n Make sure inner blade washer is in place befor e positioning blade on the spindle of the saw .
20 21 ASSEMBL Y Fig. 23 FENCE SOCKET HEAD SCREW(S) Fig. 21 VIEW OF MITER T ABLE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED Fig. 22 VIEW OF MITER T ABLE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED Fig.
22 23 SQUARING THE SAW BLADE TO THE FENCE See Figures 24 - 27. n Unplug the saw . n Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position. n Loosen the miter lock handle. n Rotate the miter table until the pointer is positioned at 0 ° .
22 23 ASSEMBL Y FENCE MITER T ABLE COMBINA TION SQUARE BLADE Fig. 28 CORRECT VIEW OF BLADE SQUARE WITH MITER T ABLE VIEW OF BLADE NOT SQUARE WITH MITER T ABLE, ADJUSTMENTS ARE REQUIRED Fig. 29 SQUARING THE BLADE TO THE MITER T ABLE See Figures 28 - 30.
24 25 This saw has two scale indicators, one on the bevel scale and one on the miter scale. After squaring adjustments have been made, it may be necessary to loosen the indi- cator screws and r eset them to zero.
24 25 TO MITER CUT n Pull out the lock pin and lift saw arm to its full height. n Loosen the miter lock handles. n Rotate the saw table until the pointer aligns with the desired angle on the miter scale.
26 27 Fig. 34 BEVEL CUT OPERA TION TO COMPOUND MITER CUT A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This type of cut is used to make picture frames, cut molding, make boxes with sloping sides, and for certain roof framing cuts.
26 27 OPERA TION Fig. 37 Fig. 36 45 ° X 45 ° COMPOUND MITER CUT n Grasp the saw handle firmly then squeeze the switch trigger . Allow several seconds for the blade to reach maximum speed.
28 29 4 PITCH OF SIDE NUMBER OF SIDES 0° 6 M- 45.00° B- 0.00° 5° 10° 15° 20° 25° 30° 35° 40° 45° 50° 55° 60° 65° 70° 75° 80° 85° 90° 5 7 8 9 10 M- 36.00° B- 0.00° M- 30.00° B- 0.00° M- 25.71° B- 0.00° M- 22.50° B- 0.00° M- 20.
28 29 CUTTING CROWN MOLDING The compound miter saw does an excellent job of cut- ting crown molding. In general, compound miter saws do a better job of cutting crown molding than any other tool made. In order to fit pr operly , crown molding must be compound mitered with extr eme accuracy .
30 31 WRONG Fig. 40 W ARNING: T o avoid a kickback and to avoid serious personal injury , never position the concave edge of bowed or warped material against the fence. CLAMPING WIDE WORKPIECES See Figure 41. When cutting wide workpieces such as a 2 in.
30 31 ADJUSTMENTS PIVOT ADJUSTMENTS NOTE: These adjustments were made at the factory and normally do not requir e readjustment. TRA VEL PIVOT ADJUSTMENT n The saw arm should rise completely to the up position by itself.
32 33 ADJUSTMENTS DEPTH STOP ADJUSTMENTS See Figure 43. n Unplug the saw . n T o adjust the depth stop use a 10 mm wrench or adjustable wrench and loosen the hex nut at the r ear of the miter saw arm. n Use a 5 mm hex key wrench to adjust the depth stop adjustment screw .
32 33 MAINTENANCE Fig. 46 NEGA TIVE (–) LASER GUIDE SUPPORT BA TTERIES CHANGING THE BA TTERIES See Figure 45.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 34 9 36 37 10 34 32 33 7 28 6 5 35 44 43 2 11 23 22 21 24 18 17 19 20 3 45 4 8 29 31 25 30 27 26 30 1 38 39 40 41 42 16 12 13.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 35 P ARTS LIST - FIGURE A Key Part No. Number Description Qty . * Standard Har dware Item – May Be Pur chased Locally ** Available fr om Div 98 – Source 980.0 1 511110000 Base.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 36 21 20 19 17 16 33 32 31 30 15 14 13 12 11 10 9 8 7 6 5 4 3 2 18 22 23 24 25 34 26 27 28 36 29 1 FIGURE B SEE NOTE NOTE : The assembly shown repr esents an important part of the double insulated system.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 37 P ARTS LIST - FIGURE B Key Part No. Number Description Qty . The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regar ding your Compound Miter Saw or when ordering r epair parts.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 38 FIGURE C 1 2 7 3 8 17 18 19 24 26 25 23 22 21 20 9 10 12 11 13 6 27 5 4 15 14 16.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 39 P ARTS LIST - FIGURE C Key Part No. Number Description Qty . 1 511348000 Rear Spring Spacer .................................................................................
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 40 1 2 4 3 7 9 12 13 14 8 5 6 10 11 17 18 19 21 22 23 24 26 27 28 25 16 15 20 29 P ARTS LIST - FIGURE D.
CRAFTSMAN COMPOUND MITER SA W – MODEL NUMBER 315.212340 & 315.242340 41 P ARTS LIST - FIGURE D Key Part No. Number Description Qty . The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regar ding your Compound Miter Saw or when ordering r epair parts.
® Registered Trademar k / TM Trademar k / SM Ser vice Mark of Sears, Roebu c k and Co. ® Marca Registrada / TM Marca de Fábrica / SM Marca de Ser vicio de Sears, Roebuc k and Co . MC Marque de commer ce / MD Marque déposé e de Sears, Ro ebuck and Co.
Een belangrijk punt na aankoop van elk apparaat Craftsman 315.21234 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 315.21234 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 315.21234 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 315.21234 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 315.21234 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 315.21234 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 315.21234 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 315.21234 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
