
English User’s Guide

1 3M™ Multimedia Projector MP7630 © 3M IPC 2000

3M™ Multimedia Projector MP7630 2 © 3M IPC 2000

INTRODUCTION - 1
Safety Instructions -1 Warranty -2
Limited Warranty - 2 Shipping Contents -3 Optional Accessories -4 Projector Description -4
Projector - 4 External Control Panel - 5 Projector Features - 6 Remote Control Description -7
Remote Control Features - 7 Installing or Replacing Batteries - 9 INSTALLATION - 10
Screen Size -10 Connecting to Various Equipment -10 OPERATION - 11
Start Up -11 Digital Keystone Correction -12 Auto Adjustment -12 Source Selection -13 Menu System -13
1. Display Menu - 14 2. Image Menu - 15 3. Image Sub-menu with AV Input - 17 4. Control Menu - 17 5. Source Menu - 20 Shutdown -21 MAINTENANCE - 22
Lamp Information -22
Use and Replacement of Lamp - 22 Status LED Indicators - 22 Lamp Replacement -23 Resetting Lamp Hours -24 Service information -25
Accessories (Included in standard packet) - 25 Description of Part Number (Not Included in Standard Packet) - 25 Ordering Parts or Getting Information - 25 TROUBLESHOOTING - 26
Common Problems & Solutions -26 Status Messages -27 SPECIFICATIONS - 28
Projector specifications -28 Timing chart -29 DIMENSIONS- 30
iii 3M™ Personal Projector MP7720 © 3M IPC 2000

Save These Instructions: The information contained in this manual will help you operate and maintain your 3M™ MP7720 Personal Projector.

3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of two years from date of purchase.
Exclusion to Warranty: The lamps are considered a consumable item and are warrantied for 90 days or 180 hours, whichever occurs first. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the war- ranty period, 3M’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.
FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio fre- quency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class “A” computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.
FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio fre- quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip- ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

The 3M™ MP7720 Projector is shipped with the necessary cables required for standard PC, Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Ventilation Hole Projection Lens

S-video cable VGA cable


3M™ Personal Projector MP7720




Auto source Lamp Status Indicator

The MP7720 Projector integrates high performance optical engine design and user-friendly electrical design, which means more reliable quality and better experience in projecting with the unit.
The MP7720 Projector offers the following features:


The remote control sensors are located in the front/ back of the projector. The distance between the sensor and the remote control unit must be shorter than 6 meters.

The image will be frozen when the FREEZE button is pressed. A “Pause” icon appears at the lower right of the screen for three seconds during the freeze function. A “Play” icon appears at the lower right of the screen for three seconds when the freeze function is released. To release the freeze function, press the FREEZE button, RETURN button or SOURCE button (when the input source is switched over during display).

By pressing ZOOM IN +, the center of the picture can be magnified. When the button is pressed again, the picture is further magnified, up to four times the original size. By pressing ZOOM OUT -, the size of the image is reduced. When the button is pressed again, the picture is further reduced until it is restored to the original size. To return to the normal display mode, press the RETURN button. (This function can be used in combination with the FREEZE function.)









Keystoning is when the projected image is noticeably wider on either the top or bottom. To correct this, press KEYSTONE +/- (hot key) on the control panel of the projector or on the remote control, then adjust the sliding bar labeled Keystone, as needed. Pressing the + button will correct keystoning at the top of the image. Pressing the - button will correct keystoning at the bottom of the image.

In some cases, you may have to optimize the picture quality manually. To do this, press the AUTO key on the control panel of the projector or on the remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function of the 3M MP7720 will show you the best picture quality.


Whenever several input sources are available, press the SOURCE key on the control panel of the projector or the remote control for selection.

Press the Menu key and the main menu will display on the screen. Press Menu again to display the page items, and press to select the sub-menus. The main menu will disappear automatically if you do not undertake any further action for 10 seconds. Press the Exit button to leave the current sub-menu, and press Exit again to leave the main menu.

Menu Layout Display Image Control Source
PC input without AV Input




Keystone · Brightness ·




Will automatically adjust the image to fit on the screen.


Phase (Auto Resize OFF)

Frequency (Auto Resize OFF)



H-position · V-position ·


This menu is only available when the input signal is from Video and S-Video.
4:9 (Normal) 16:9 (Video)
Auto PAL-M PAL-N SECAM


English (En) French (Fr) German (De) Italian (It) Spanish (Es) Portuguese (Po) Traditional Chinese (TC)
Normal V-Inv (Vertically Inverted) H-Inv (Horizontally Inverted) H/V-Inv (Horizontally and Vertically Inverted) will invert image to display properly according to position of projector.
Language · Mirror ·


Will turn off the power after 60 minutes.

Will restore the projector to its factory default settings.
Auto off · Reset ·












Projector Remote Control ·

The projector lamp has a normal operating time of approximately 1200 to 1500 hours, called the lamp life. During the normal lamp life, the picture will be bright and the colors clear. If the lamp is used beyond the normal lamp life, the picture will become dark and the colors poor. Always replace lamps with new ones. Using an old lamp in the projector could cause a malfunction. When the power is turned on, the LAMP indicator will light up red or a message will be displayed to indicate when it is time to replace the lamp. Consult your dealer.
Lamp Exceed Service Hours — When this LED lights red continuously, it is warning you that the lamp has exceeded 1500 service hours. Replace the projection lamp immediately.
CHANGE THE LAMP, AND RESET THE LAMP TIMER — The lamp has been in operation for 1200 hours.
CHANGE THE LAMP, THE POWER WILL TURN OFF AFTER 20 HOURS — The lamp has been in operation for 1479 hours, and the power will turn off after 20 more hours.
CHANGE THE LAMP! — The lamp has been in operation for over 1500 hours, and the power will turn off automatically in 10 minutes.
All of these messages will not display for more than 3 minutes, but each message will be displayed whenever you turn on the lamp again.
Lamp is not well attached — When the LED blinks rapidly, it indicates that the lamp is not attached properly.
Temperature is too high — When the projector’s internal temperature is too hot to operate safely, the LED blinks slowly for one minute and the lamp turns off automatically.
If the LED light is off, it means that the projector’s lamp and temperature are operating under normal conditions.





To reduce the risk of cuts to fingers and damage to internal components, use cau- tion when removing lamp glass that has shattered into sharp pieces.
To reduce the risk of cuts to fingers and/or decreasing image quality by touching the lens, do not touch the empty lamp compartment when the lamp has been removed.
This lamp contains mercury. Consult your local hazardous waste regulations and dispose of this lamp in a proper manner.
If you replace the lamp after 1500 hours of operation, please proceed as follows within 10 minutes of powering on.
Press the Exit button on the projector or the remote control for 3 seconds to display the total used lamp time.

Press the MENU button on the projector or the remote control during the lamp hour message. An adjustment message will appear.


Power Cord (EU) 78-8118-8840-9
Power Cord (US) 78-8118-8838-3
Power Cord (UK) 78-8118-8841-7
Signal Cable 78-8118-8710-4
RCA Cable DY-0205-1008-6
S-Video cable 78-8118-3238-1
PC - PC Audio Cable 78-8118-8290-7
Audio - PC Audio Cable DY-0205-1359-3
Remote Control 78-8118-8842-5
3-2 converter 78-8118-8704-7
Description of parts Part number
Deluxe carry case (hold projector and notebook) 78-6969-9203-7
120W Lamp module 78-6969-9264-6
Description Part Number ·

NO POWER • Plug the power cord into the AC Inlet.
NO PICTURE • Check that you have selected the proper input source.
POOR COLOR • Select the correct video system.
IMAGE IS BLURRED • Press the Auto key on the control panel of the projector or the remote control unit to get better picture quality.

On Screen Messages Meaning
SEARCHING Projector is searching for input.
Projector has identified the input signal and is processing the auto image adjustment.
SYNC IS OUT OF RANGE Input signal’s frequency exceeds that of projector’s
The lamp has been in operation for 1200 hours. Lamp replacement is recommended.
CHANGE THE LAMP, THE POWER WILL TURN OFF AFTER 20 HOURS
The lamp has been in operation for 1479 hours, and the power will turn off after 20 more hours. Replace the lamp as soon as possible.
CHANGE THE LAMP! The lamp has been in operation for over 1500 hours, and the power will turn off automatically in 10 minutes. Replace the lamp immediately.

Display system 1-CHIP DMD
Lamp 120W VIP lamp
Power supply AC90 ~ 240V, 6.5A ~ 2.9A, 50/60 Hz (Automatic)
Power consumption 200 W (Max)
Dimensions 186 mm (W) x 220 mm (H) x 52 mm (D)
Audio Signal Input Mini Jack Mono Audio Terminal
1 Watt speaker x 1

Resolution H Sync (kHz) V Sync (kHz) Remark
640x350 31.5 70.1
640x400 37.9 85.1 VESA
720x400 31.5 70.0
720x400 37.9 85.1 VESA
640x480 31.5 60.0 VESA
640x480 37.9 72.8 VESA
640x480 35 66.7 Macintosh
640x480 43.3 85.0 VESA
800x600 35.2 56.3 VESA
800x600 37.9 60.3 VESA
800x600 46.9 75.0 VESA
800x600 48.1 72.2 VESA
800x600 53.7 85.1 VESA
832x624 49.7 74.5 Macintosh
1024x768 48.4 60.0 VESA
1024x768 56.5 70.1 VESA
1024x768 60.0 75.0 VESA
1024x768 68.7 85.0 VESA
1280x1024 64.0 60.0 VESA


· ™

Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.
Warranty and Limited Remedy. This product will be free from defects in material and manufacture for a period of two years from the date of purchase. Exclusion to Warranty: The lamps are considered a consumable item and are warrantied for 90 days or 180 hours, whichever occurs first. 3M MAKES NO OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Limitation of Liability. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we’re the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l’Oise 95006 Cerge Pontoise Cedex France
Litho in USA Copyright © 2001 3M IPC.
All Rights Reserved 78-6970-9066-6 Rev. B
Veelvoorkomende problemen, mogelijke oorzaken en oplossingen.
| Probleem | Mogelijke oorzaak | Oplossing | |
|---|---|---|---|
| NO POWER | • Plug the power cord into the AC Inlet. • Plug the power cord into the power Inlet. • Wait two minutes after the projector has been turned off before turning the projector back on. | p.29 | |
| NO PICTURE | • Check that you have selected the proper input source. • Ensure all cables are connected properly. • Adjust the brightness and contrast. • Remove the lens cap. | p.29 | |
| IMAGE ISN’T SQUARE ON THE SCREEN | • Reposition the unit to improve its angle on the screen. • Use the keystone correction function key on the control panel of the projector or the remote control unit. | p.29 | |
| POOR COLOR | • Select the correct video system. • Adjust brightness, contrast, or saturation. | p.29 | |
| IMAGE IS BLURRED | • Press the Auto key on the control panel of the projector or the remote control unit to get better picture quality. • Adjust the focus. • Reposition the unit to improve its screen angle. • Ensure the distance between the unit and screen is within the adjustment range of the lens. | p.29 | |
| REMOTE CONTROL DOESN’T WORK | • Replace the battery with a new one. • Make sure there is no obstacle between the remote control and the unit. • Stand within 4 meters (13 feet) of the unit. • Make sure nothing is blocking the receiver on the control pad. | p.29 |
Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.
Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.