Gebruiksaanwijzing /service van het product HBS-56S van de fabrikant Jet
Ga naar pagina of 28
Operating Instructions and Parts Manual 5 x 6-inch Horizontal Band Saw Model HBS-56S For use with machines wit h Serial Numbers 06080307 and hig her WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-414457A Ph.: 800-274-6848 Revision B 9/06 www.
2 Warranty and Service WMH Tool Group, Inc., warrants every product it se lls. If one of our tools nee ds service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service.
3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents ........................................................
4 Warning 1. Read and understand the entire o wner's manual bef ore attempting assembly or operation. 2. Read and understand the warnings posted on the ma chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king aroun d, carrying on a conversation and “horse-play” a re careless acts that can result in seriou s injury.
6 Introduction This manual is provided by WMH Tool Grou p covering the safe operation and maintenance procedures for a JET Model HBS-56S Horizontal Band Saw. Thi s ma nual contains in structions on installation, safety precautions, general o perating procedures, m aintenance instructio ns and part s breakdown.
7 Shipping Contents Open carton and check for shipping damage. Report any damage immediately to your distributor and shipping a gent. Do not discard any shipping material until the band saw i s assembled and running pr operly.
8 Read and understand the entire conte nts of this manual before attempting set-up or operation! Failure to comply may cause serious injury. Assembly of Stand Tools required for assembl y: Two 1/2-inch wrench ( Note: A ratchet wren ch may speed assembly time.
9 Assembly of Band Saw Tools required for assembl y: – cross point (Phillips) screwdriver – 3mm and 4mm hex wrenches (p rovided) – 1/2" and 9/16" wrenches Remove any plastic or holding straps from around the band saw. Area s of the machine have been given a protective coatin g at the factory.
10 4. Lift up on the motor and install the belt around the pulley groov es, as shown in Figure 4. Allow the motor to dro p back down, then push it down farther to tension the belt. (For further information o n belt tension and belt position on the grooves, see page 15.
11 This band saw is pre-wired for 115 volt and is equipped with an electric cord having an equipment-grounding conductor and a grounding plug similar to that sho wn in Figure 6. The plug must be inserted into a matchin g outlet that is properly installed and gro unded in accordance with all local codes and ordinan ces.
12 1. Disconnect machine from powe r source. 2. Open the switch b ox and connect the lead s according to th e wiring dia gram inside the switch box. This diagram is also shown on page 26 of this manual.
13 4. If the vise and bla de are square but the pointer (D, Figure 10) i s off slightly, loosen the screw and adjust the pointer until it line s up with zero on the scale. Tighten the screw. NOTE: The handle (A, Fig ure 10) is adj ustable. Simply lift up on the handle and rotate it on the pin.
14 3. Slide the movable jaw by hand until the jaw contacts the workpiece. 4. Rotate the vise handwhee l clockwise to re- engage the lead screw, and continue the tightening process of the jaw until the workpiece is securely clam ped. 5. The quick rel ease function can be used to back off the movable jaw when the cut is finished.
15 Blade Tension Use the knob (Figure 15 ) to tension the blade. Clockwise tightens the blade, co unterclockwise loosens it. Blade Tracking Tracking the blade requires that the band sa w be operating while the back blade cover is remov ed. Use extreme caution and keep hands a w ay from blade.
16 Belt Tension 1. Disconnect band saw from power source. 2. Open the pulley cover. 3. Loosen the knob (see A, Figure 3 ), and push down on the motor to tighten the belt. 4. Tighten the knob (A, Figure 3). 5. Check the tension by usin g moderate finger pressure about midway between the pulleys.
17 Blade Replacement Use caution and proceed slowly when w orking with or around a band saw blade. Use gloves when handling it. 1. Disconnect band saw from power source.
18 Vertical Bow Position 1. The band saw can be placed in vertical position to facilitate blade ch anges, maintenance, etc. Unscrew the knob (Fi gure 22) and slide it out t o disengage the hydraulic cylinder. 2. Raise the bow all the way. 3. The sto p screw (Figure 23) has been pre- set at the factory.
19 5. Open the valve on the hy draulic cylinder to allow the bow to descen d in a gradual an d controlled manner. 6. The machine will shut off at the completion of the cut. Remove the workpiece. 7. Close the hydraulic cylinder valve, and raise the bow in preparation for the next cut.
20 Troubleshooting Trouble Probable Cause Remedy No incoming power. Check plug connection. Blown electrical panel fuses. Replace fuses. Motor will not start. Defective motor, switch, power cable, or plug. Qualified electrician/service personnel should inspect these items.
21 Parts List: HBS-56S Band Saw Index No. Part No. Description Size Qty 1 ............... TS-0051031 ............. Hex Ca p Bolt ........................................................ 5/16”x3/4” .......... .......... 4 2 ............... TS-0561011 .
22 Parts List: HBS-56S Band Saw Index No. Part No. Description Size Qty 89 ............. OS-15375................. Oil Seal................................................................. .............. ...................... 2 90 ............. HVBS462-090 .
23 Parts List: HBS-56S Band Saw Index No. Part No. Description Size Qty 313 ........... TS-0208071 ............. Hex Socket Head Screw ...................................... 5/ 16"x1-1/4" ................ 2 314 ........... TS-0267041 .......
24 Parts List Index No. Part No. Description Size Qty 393 ........... HBS56S-393 ............ Wire Ring ............................................................. ..................... ............... 1 394 ........... TS-081C032 ............. Cross Round He ad Screw .
25 Bow Assembl y (Page 2 of 3) 97-1(2).
26 Bow Assembl y (Page 3 of 3).
27 Base and Cabinet Assembly.
28 Electrical Connections WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.co m.
Een belangrijk punt na aankoop van elk apparaat Jet HBS-56S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Jet HBS-56S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Jet HBS-56S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Jet HBS-56S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Jet HBS-56S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Jet HBS-56S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Jet HBS-56S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Jet HBS-56S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
