Gebruiksaanwijzing /service van het product JWCS-10 van de fabrikant Jet
Ga naar pagina of 16
Owner's Manual XACTA ® Fence II Homeshop 30/52 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708928Z Ph.: 800-274-6848 Revision B 03/06 www.
2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service.
3 Table of Contents WARRANTY A ND SERVICE ........................................................................................................... ............. 2 Table of Contents ...................................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks , master switch es or by removing starter keys. 23. Give your work undivided attention. Looking ar ound, carrying on a conversatio n and “horse-play” are careless acts that can result in serious inj ury.
6 Unpacking Open shipping carton s and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manu al thoroughly for assembly, alignment, and ma intenance instructions.
7 Installation Tools required Drill with 5/16" drill bit 10mm open end wrenches Cross point screwd river Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for in stalling the XACTA Fence II and Rail System on JET Models JWCS-10 and JWTS-10 series table saws.
8 Back Rail Installation 1. Locate the back rail which is 1-1/2" x 1-1/2" with holes running along one si de only. The height of the back rail when atta ched to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4.
9 3. Tap down the extension table at various points along its edge where it meets the saw table, until it is level with the saw table (Figure 7). As one part of the edge becomes level with the table, tighten the clamp on that side. Then move to the other side and re peat, until the full length of the edge is level with the saw table.
10 Guide Tube Referring to Figure 11: The guide tube (A) is placed on to p of the front rail (B) and is mounted with t he scale facing toward the operator. 1. Align the holes in the bottom of the guide tube (A) with the holes in the front rail (B). 2.
11 Fence Adjustments Note: Fence adjustments should be perform ed in the order given. Leveling Fence to the Saw Table 1. Place the fence on the table and lock it. 2. View the fence from the left side of the saw (Figure 14). Look for the spa ce between the table and the fence bottom to be equal along the entire length of the fence (A, B, Fig.
12 90 ° to the Table Adjustment 1. Place the fence on the saw table and lock it. 2. Place a square (A, Fig. 17) on the table next to the fence. The fence should b e 90 ° to the table. 3. If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (B, Fig.
13 Parts Ordering Replacement Parts To order parts or reach our se rvice department, call 1-800 -274-6848 between 7:30 a.m. and 5:30 p.m. (CST), Monday through F riday. Having the Model Number and S erial Number o f your machine available when you call will allow us to serve you quickly and accurately.
14 Parts for XACTA Fence II Homeshop 30/52 Rail Assembly Index No. Part No. Description Size Qty 1 ............... HF2-201 ................... Front Fence Rail - Standard................................. ......................... ........... 1 .......
15 Parts for the XACTA Fence II Homeshop 30/52 Leg Assembly Index No. Part No. Description Size Qty 1 ............... XF2-301 ................... Leg ....................................................................... .............................
16 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m.
Een belangrijk punt na aankoop van elk apparaat Jet JWCS-10 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Jet JWCS-10 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Jet JWCS-10 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Jet JWCS-10 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Jet JWCS-10 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Jet JWCS-10 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Jet JWCS-10 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Jet JWCS-10 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
