Gebruiksaanwijzing /service van het product ET-3402-J van de fabrikant John Deere
Ga naar pagina of 20
7 1/4 Inch Circular Saw Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE CIRCULAR SAW AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
2 7 1/4 Inch Circular Saw Operator's Manual Congratulations on the purchase of your new Circular Saw! You can be assured your circular saw was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
7 1/4 Inch Circular Saw Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-11 GENERAL SAFETY RULES ....................................
4 7 1/4 Inch Circular Saw Operator's Manual W ARNI N G W A R N I NG SI N T HE M A NUA LS . W A RN I NG SI N T HE M A NUA LS . CA U T I ON OC A UT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O.
7 1/4 Inch Circular Saw Operator's Manual 5 KEEP WORK AREA CLEAN AND WELL LIT. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations.
6 7 1/4 Inch Circular Saw Operator's Manual DON'T OVERREACH Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories.
7 1/4 Inch Circular Saw Operator's Manual 7 OUTDOOR USE EXTENSION CORDS When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT Watch what you are doing. Use common sense. Do not operate tool when you are tired.
8 7 1/4 Inch Circular Saw Operator's Manual CAUTION ALWAYS KEEP THE MOTOR AIR VENT FULLY OPENED A constantly open motor air vent is necessary to allow air to come in and out for cooling the motor. Do not allow it to become clogged up, even if dust is blown through it.
7 1/4 Inch Circular Saw Operator's Manual 9 CAUTION SUPPORT LARGE PANELS Large panels must be supported as shown in Fig. 1 to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of saw on the work piece, the saw shall be rested on the larger portion and the smaller piece cut off.
10 7 1/4 Inch Circular Saw Operator's Manual LOWER GUARDS Raise lower guard with the retracting handle (Lever). ADJUSTMENTS Before cutting be sure depth and bevel adjustments are tight. USE ONLY CORRECT BLADES IN MOUNTING Do not use blades with incorrect size holes.
7 1/4 Inch Circular Saw Operator's Manual 11 EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
12 7 1/4 Inch Circular Saw Operator's Manual Functional Description MODEL: ET-3402-J CIRCULAR SAW NAME OF PARTS: (Fig. 3) NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
7 1/4 Inch Circular Saw Operator's Manual 13 Operation APPLICATIONS: Cutting various types of wood. PRE-OPERATION: Before using the Electric Power Tool, complete the following preparations: 1. Power source: Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate.
14 7 1/4 Inch Circular Saw Operator's Manual Operation OPERATION: CUTTING PROCEDURES: CAUTION: RECHECK THAT THE SAW BLADE IS SECURELY CLAMPED. CONFIRM THAT THE CLAMP LEVER FOR ADJUSTING THE SLOT DEPTH, THE WING-BOLT FOR ADJUSTING THE ANGLE OF INCLINATION.
7 1/4 Inch Circular Saw Operator's Manual 15 Operation POCKET CUTTING: CAUTIONS: RELEASE TRIGGER AFTER CUTTING WORK AND DISCON- NECT PLUG FROM POWER SUPPLY BEFORE ANY ADJUST- MENT. NEVER TIE OR WEDGE THE SAFETY COVER IN A RAISED POSITION. OPERATION (CONTINUED): 1.
16 7 1/4 Inch Circular Saw Operator's Manual Operation MOUNTING AND DISMOUNTING THE SAW BLADE: CAUTION: TO AVOID SERIOUS ACCIDENT, ENSURE THE SWITCH IS IN THE OFF POSITION, AND THE POWER SOURCE IS DISCON- NECTED. 1. Dismounting the saw blade (Fig.
7 1/4 Inch Circular Saw Operator's Manual 17 Maintenance and Inspection MAINTENANCE AND INSPECTION: CAUTION: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG DURING MAINTENANCE AND INSPECTION.
18 7 1/4 Inch Circular Saw Operator's Manual STANDARD ACCESSORIES: CAUTION: RECOMMENDED ACCESSORIES FOR THE ELECTRIC POWER TOOL ARE MENTIONED IN THIS MANUAL. THE USE OF ANY OTHER ATTACHMENT OR ACCESSORY IS HAZARDOUS. 1. Saw Blade 1 2. Wrench 1 3.
7 1/4 Inch Circular Saw Operator's Manual 19 Notes.
20 7 1/4 Inch Circular Saw Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 7 1/4-Inch Circular Saw Operator's Manual 111 Code No.
Een belangrijk punt na aankoop van elk apparaat John Deere ET-3402-J (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen John Deere ET-3402-J heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens John Deere ET-3402-J vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding John Deere ET-3402-J leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over John Deere ET-3402-J krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van John Deere ET-3402-J bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de John Deere ET-3402-J kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met John Deere ET-3402-J . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
