Gebruiksaanwijzing /service van het product QM20 van de fabrikant Manitowoc Ice
Ga naar pagina of 28
QM20 Series Ice Machine Installation, Use and Care, and Service Manual Thank you for selecting a Manitowoc Ice Machine, the dependability le ader in ice making equipment and related products. With proper care and m aintenance, your new Manitowoc Ice Machine will provide you with many years of reliable and economical performance.
Safety Notices When using or servicing a QM Series Ice Machine, be sure to pay close atten tion to the safety notices in this manual. Disregarding the notices may lead to serious injury and/or damage to the ice machine.
Table of Contents i Table of Contents Section 1 - General Information Model/Serial Number Location ................................................................................................... ................... 1-1 Owner Warranty Registration Card .
Table of Contents ii THIS PAGE INTENTIONALLY LEFT BLANK.
Section 1 General Information 1-1 Section 1 General Information Model/Serial Number Location Record the model and serial number of your ice machine in the space prov ided below. These numbers are required when requesti ng information from your Manitowoc distributor, service rep resentative, or the factory.
General Information Section 1 1-2 Owner Warranty Registration Card GENERAL The packet containing this manual also includes warranty information. Warrant y coverage begins the day your new ice machine is installed. Important Complete and m ail the OWNER W ARRANTY REGISTRATION CARD as soon as possible to validate the installation date.
Section 1 General Information 1-3 Residential Warranty Coverage WHAT DOES THIS LIMITED WARRANTY COVER ? Subject to the exclusions and limitations below, Manitowo c Ice, Inc.
1-4 General Information Section 1 INTENTIONALLY LEFT BLANK.
Section 2 Installation Instructions 2-1 Section 2 Installation Instructions Dimensions SV1717 20.54 cm (8.09”) 3.73 cm (1.47”) 19.05 cm (7.50”) 1.90 cm ± 0.63 cm (0.75” ± 0.25”) 15.72 cm (6.19”) 38.10 cm (15.00”) 76.20 cm (30.00”) 55.
Installation Instructions Section 2 2-2 Location of Ice Machine The location selected for th e ice machine must meet the following criteria. If a ny of these criteria are not met, select another location. • The location must be indoors. • The location must be free of airborne and other contaminants.
Section 2 Installation Instructions 2-3 Electrical Service GENERAL WARNING All wiring must conform to local, state and national codes. WARNING Never use an extension co rd. If an outlet is not within reach of the ice m achine’s power cord, have a proper amperage outlet wi red closer to t he ice machine.
Installation Instructions Section 2 2-4 ELECTRICAL CORD STRAIN RELIEF To prevent strain at the electrical connection inside the ice machine, an electrica l cord str ain re lief device must be installed on the rear panel of the ice machine. 1. Disassemble the strain relief devic e into its three components.
Section 2 Installation Instructions 2-5 Water Service/Drains WATER SUPPLY Local water conditions may require treatment of the water to inhibit scale formation, filter sediment, and remove chlorine odor and taste.
Installation Instructions Section 2 2-8 Typical Water Supply and Drain Line Sizing and Connections SV1708 ICE MAKING WATER INLET TUBING 0.95 cm (3/8”) MINI MUM INSIDE DIAMET ER ICE MAKING/BIN WATER DRAIN TUBING 1.
Section 3 Ice Machine Operation 3-1 Section 3 Ice Machine Operation Sequence of Operation Control Board Relays Ice Making Sequence of Operation 1 Compressor 2 Hot Gas Valve Water Fill Valve 3 Water Pump Fan Motor Length of “ON” Time Start-Up 1 1. Water Purge Off On Off 2.
Ice Machine Operation Section 3 3-2 Ice Thickness Adjustment QM-20 dice ice cube formati on is slightly different from our previous models. Manitow oc ice machines have a unique cube shape. It is normal to have a dimple in the ice c ube (a concave indentation in the cube).
4-1 Section 4 Maintenance Section 4 Maintenance Interior Cleaning and Sanitizing GENERAL You are responsible for maintaining the ic e machine in accordance with the inst ructions in this m anual. Maintenance procedures are not covered by the warranty.
Maintenance 4-2 Section 4 Step 4 Wait until water f lows over the evaporator (about three minutes) then add the proper amount of Manitowoc Ice Machine Clean er to the water trough.
4-3 Section 4 Maintenance Parts Removal Overview WAT ER TROUGH OVERFLOW TUBE WAT ER DISTRIBUTION TUBE WATER PUMP AND BRACKET A SSEMBLY WAT ER P UM P OUTLET HOSE EVAPORATOR A SSEMBLY (REMAINS IN PLA CE.
Maintenance 4-4 Section 4 WAT ER P UM P POWER CORD OUTLET B. Remove the Overflow Tube • To remove the tube, lift it up while using a slight back and forth motion to loosen it from the drain hole. When installing the tube, be sure it is completely inserted into the drain ho le to prevent water leakage during normal operation.
4-5 Section 4 Maintenance Step 7 Mix a solution of cleaner and warm water. Depending on the amount of mineral buildup, a larger quantity of solution may be required. Use the ratio in the table below to mix enough solution to thoroughly clean all parts.
Maintenance 4-6 Section 4 WARNING Disconnect electric power to th e ice machine at the electric switch box before proceed ing. Step 17 Repeat step 6 to remove parts for hand sanitizing. Step 18 Mix a solution of sanitiz er and warm water. Solution Type Water Mixed With Sanitizer 23 L.
4-7 Section 4 Maintenance CLEANING THE CONDENSER WARNING Disconnect electric power to th e ice machine at the electric service switch before cleani ng the condenser. Air-Cooled Condenser A dirty condenser restrict s airflow, resulting in excessively high operating temperatures.
4-8 Maintenance Section 4 Removal from Service/Winterization GENERAL Special precautions must be taken if the ice m achine is to be removed from se rvice for an extended period of time or exposed to ambient temperatures of 0 ° C (32 ° F) or below.
Section 5 Before Calling for Service 5-1 Section 5 Before Calling for Service Checklist If a problem arises during operation of your ice machine, follow the checklis t below before calling for service. Problem Possible Cause To Correct Ice machin e does not operate.
Before Calling for Service Section 5 5-2 Problem Possible Cause To Correct Ice machine produ ces shallow or in co mplete c ubes, or the ice fill pa ttern on the evaporator is incomplete . Water le vel is low. Be sure the overflow t ube is fully seated to prevent water leak age.
.
MANITOWOC ICE, INC. 2110 South 26th Street P.O. Box 1720 Manitowoc, WI 54221-1720 Phone: ( 920) 68 2-0161 Fax: ( 920) 683-7 585 Web Site - www.manitowocice.
Een belangrijk punt na aankoop van elk apparaat Manitowoc Ice QM20 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Manitowoc Ice QM20 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Manitowoc Ice QM20 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Manitowoc Ice QM20 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Manitowoc Ice QM20 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Manitowoc Ice QM20 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Manitowoc Ice QM20 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Manitowoc Ice QM20 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
