Gebruiksaanwijzing /service van het product 250101 van de fabrikant ParaBody
Ga naar pagina of 18
1 250101 HOME GYM Part # 6719701 Revision: 09/9/98 ASSEMBL Y INSTRUCTIONS.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the Parabody 250101 Home Gym. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 P AR TS LIST 3 PA RT # 6594303 6593703 6593503 6594102 6501302 6594702 6718503 6718203 6717803 6717502 6275302 6597402 6468401 6125101 6194601 6514401 6189501 31 16101 31 16201 6714601 6266001 62705.
FIGURE 1 4 STEP 1 • Loosely assemble the REAR UPRIGHT (9) to the BASE (8) using two 1/2 X 3” BOLTS (46), two 1/2” FLAT WASHERS (39), and two 1/2” LOCK NUTS (40). See FIGURE 1. • Loosely assemble the FRONT UPRIGHT (2) to the BASE (8) using one 3/8 X 2-3/4” BOLT (48) and one 3/8” LOCK NUT (41) as shown in FIGURE 1.
5 FIGURE 3 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 3 FIGURE 2 • Insert two WEIGHT PLATE BUSHINGS (23) into the “PARABODY” side of each of the fifteen WEIGHT PLATES (58) as shown in FIGURE 2. STEP 2 • Insert two GUIDE RODS (16) into the BASE (8) as shown on FIGURE 3.
FIGURE 4 6 STEP 4 FIGURE 5 STEP 5 • Swing the GUIDE RODS (16) under the TOP BOOM (7) as shown on FIGURE 4. • Loosely assemble the TOP BOOM (7) to the REAR UPRIGHT (9) using two 1/2 X 3” BOLTS (46), two 1/2” WASHERS (39), and one 1/2” LOCKNUT (40).
7 FIGURE 6 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Install two 5/16” SET SCREWS (50) into the top of the PRESS ARM (3) as shown in FIGURE 6. • Insert two 3/4" FLANGE BEARINGS (29) into the TOP BOOM (7) as shown in FIGURE 6.
FIGURE 7 8 • Loosely assemble two 4-1/2” PULLEYS (18) to the PRESS ARM (3) using two 3/8 X 7-1/2” BOLTS (51), four 3/8” WASHERS (38), four 3/8 X 1” SPACERS (32), and two 3/8” LOW HEIGHT LOCK NUTS (43) as shown in FIGURE 7. Once both PULLEYS are installed, you may securely tighten these two connections.
9 FIGURE 8 STEP 8 • Securely assemble one SPRING PIN ASSEMBLY (35) and one 3 PRONG KNOB (33) to the FRONT UPRIGHT (2) as shown. • Apply eight PARAGLIDES (57) to the INSIDE of the tube on the FRONT UPRIGHT (2) as shown.
FIGURE 9 10 STEP 9 • Insert two 1/2” FLANGE BEARINGS (30) into the the LEG CURL EXT (1) as shown. • Assemble the LEG CURL EXT (1) to the FRONT UPRIGHT (2) using one 1/2 X 3” BOLT (46) and one 1/2” LOW HEIGHT LOCK NUT (42). (Note: Tighten this connection enough to remove excess play yet allow the LEG CURL EXT to rotate freely.
11 FIGURE 10 STEP 10 • Securely assemble the CALF BLOCK (10) to the BASE (8) using two 3/8 X 2-3/4” BOLTS (48), two 3/8” WASHERS (38), and two 3/8” LOCK NUTS (41) as shown in FIGURE 10. (Note: The CALF BLOCK can be assembled to either side of the BASE.
12 FIGURE 11 • Attach two 4 X 7” ROLLER PADS (15) to the FRONT UPRIGHT (2) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11. STEP 11 • Attach two 4 X 7” ROLLER PADS (15) to the PRESS SEAT (4) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11.
FIGURE 13 13 STEP 13 • Securely assemble the ball end of the WEIGHT STACK CABLE (26) and one 3-1/2” PULLEY (19) to the TOP BOOM (7) using one 3/8 X 2-3/4” BOLT (48), two 3/8” FLANGE SPACERS (36), and one 3/8” LOCK NUT (41) as shown in FIGURE 13.
14 FIGURE 14 STEP 14 • Securely assemble the WEIGHT STACK CABLE (26) and two 3-1/2” PULLEYS (19) to the TOP BOOM (7) using two 3/8 X 2- 3/4” BOLTS (48), four 3/8” FLANGE SPACERS (36), and two 3/8” LOCK NUTS (41) as shown in FIGURE 14. (Note: Loop the CABLE over the PULLEYS prior to inserting it into TOP BOOM.
15 FIGURE 15 STEP 15 • Securely assemble one 4-1/2” PULLEY (18) to the FLOATING PULLEY BRACKET (6) using one 3/8 X 1-3/4” BOLT (49) and one 3/8” LOCK NUT (41) as shown in FIGURE 15.
FIGURE 16 STEP 16 • If upon completion of assembly, the HEAD PLATE (20) does not sit on top of the first WEIGHT PLATE (58), push the HEAD PLATE (20) down, insert the WEIGHT STACK PIN (34) and perform several repetitions at the press station. This will relax the cable system and prevent the HEAD PLATE (20) from lifting up.
17 • Attach the LAT BAR (11) to the ball end of WEIGHT STACK CABLE (26) using one SNAP LINK (28) as shown in FIGURE 16.. STEP 17 • Attach the LOW ROW BAR (24) or the ANKLE STRAP (25) to the ball end of LEG CURL CABLE (27) using two SNAP LINKS (28) and one 12 LINK CHAIN (31) as shown in FIGURE 16.
1 FIGURE 1 STEP 1 • If upon completion of assembly , the HEAD PLA TE (20) does not sit on top of the first WEIGHT PLA TE (58), push the HEAD PLA TE (20) down, insert the WEIGHT ST ACK PIN (34) and perform several repetitions at the press station. This will relax the cable system and prevent the HEAD PLA TE (20) from lifting up.
Een belangrijk punt na aankoop van elk apparaat ParaBody 250101 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ParaBody 250101 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ParaBody 250101 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ParaBody 250101 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ParaBody 250101 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ParaBody 250101 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ParaBody 250101 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ParaBody 250101 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
