Gebruiksaanwijzing /service van het product 425 van de fabrikant ParaBody
Ga naar pagina of 30
Serious Steel 425 ~~9 ~ HOME GYM ASSEMBLY INSTRUCTIONS PART #6658301 1 11/18/96.
! ! ! ATTENTION ! ! ! UNL ESS 0 THER WISE SHO WN, ALL CONNECTIONS WILL CONSIST OF ONE (1) BOLT, TWO C) WASHERS. (1) LOCKNUT. ONE BOLT WASHER~ CKNUT NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4O 41 42 43 44 45 46 47 48 49 5O 51 52 53 54 55 56 57 58 PART # DESCRIPTION 6571603 PRES.
425 Assembly Instructions 13/8 X t/2" LD~/ HE’.[15HT NUT Step 1 A. Insert two 1/2 IN. FLANGE BEARINGS (9.5) into the SWIVEL PULLEY BRACKET (16) os shown drawing. B. Assemble the SWIVEL PULLEY BRACKET (16) to the PRESS BASE (1) as shown on drowing, using 1/2 X 4 IN.
318 X 2-3/4"~ 112 X 3-t12" 1 / / I / / I / / I / // // / / / 3/8 X 2" S|ep 2 A. SECURELY assemble one 3-1/2 X 1 IN. PULLEY (100) to the PRESS LEVER (15) as shown drawing, using one 5/8 X 2-5/4 IN. BOLT (75), fwo 5/8 IN. FLANGE SPACERS (97), and one 5/8 LOCK NUT (91).
o Step 3 A. SECURELY assemble one :5-1/2 × 1 IN. PULLEY (100) fo fhe fr’onf flat of -~he BASE (7) as shown on drawing, using one 3/a × 2 IN. BOLT (76), one 2-3/a IN. CABLE RETAINING CLIP (162), one 5/8 IN. WASHER (69), and one 5/8 IN. LOCK NUT (91).
* ALL CONNECTIONS USE 5/8 × 5 IN. BOLTS Sfep 4 LOOSELY assemble fhe FRONT (22)and MIDDLE UPRIGHTS (11) fo fhe BASE (7) using 5/8 X 5 IN. BOLTS (75), eight 5/8 IN.
3/8 X 3", Step 5 A. LOOSELY assemble fhe PRESS BASE (1) to the REAR (15) AND MIDDLE UPRIOHTS (11),using four 5/8 X 5 IN. BOLTS (75), eight 5/B IN. WASHERS (69), and four 5/8 IN. LOCK NLTS (91). B. LOOSELY assemble fhe PRESS BASE (1) to the BASE (7) using two 1/2 X 5-1/4 IN.
Step 6 LOOSELY assemble one 3-1/2 X 1 IN. PULLEY (100), and one 4-1/2 X 1 IN. PULLEY (99) to inside of fhe TOP BOOM (5), using one 5/8 X 2-3/4 IN. BOLT (75), one 3/8 X 2-1/4 IN. BOLT (71), fwo ,5/8 IN. FLANGE SPACERS (97), fwo 3/8 IN. WASHERS (69), and fwo 3/8 IN.
iI~ x 3" 318 × 3"~ S~ep 8 LOOSELY ossemble the TOP BOOM (5) fo fhe fop of ,he MIDDLE (I I) ond FRONT (22) UPRIGHTS using four 3/8 X 3 IN. BOLTS (73), eight 3/8 IN. WASHERS (69), ond four :5/8 IN LOCI< NUTS (91). LOOSELY ossemble fhe TOP BOOM (5) to the fop of the REAR (13) UPRIGHT using fwo 1/2 x 3 BOLTS (65), fwo 1/2 IN.
3/8 X i" Siep 9 A. Inserf the GUIDE RODS (27) into ihe BASE (7) os shown on drawing. (NOTE: LUBRICATE GUIDE RODS WITH A SILICON OR TEFLON SPRAY THAT IS AVAILABLE AT MOST HARDWARE STORES). NOTE:THE TWO WEIGHT STACK SPACERS (25), AND THE TWO ,3/4 IN.
(CONTINUED FROM PAGE 12..) C. SECURELY assemble the WEIGHT STACK SHAFT (104) fo the HEAD PLATE (105) as shown on drawing, using one 5/B X 1 IN. BUTTON HEAD CAP SCREW (78) and one 5/8 IN. BLACK LOCK WASHER (77). D. Shop two WEIGHT PLATE BUSHINGS (107) each, into fifteen WEIGHT PLATES (105) as shown.
S~ep 1 1 A. Pre-ossemble the PEC SEAT (21), using the following steps: ~ SECURELY ossemble one of the BACK/SEAT PADS (.55) fo the PEC SEAT (21), using two X 5 IN.
~ i/e" LO~/ HEIGHT NUT ,, // @-__ .... " I I ,’ ’, 2 IN, SQ, END CAP~ Step 12 A. Assemble the LEG CURL/EXTENSION ARM (25) to the FRONT UPRIGHT (22) using the follow;ng steps: ~lnsert two 1/2 IN. FLANGE BEARINGS (95) to the FRONT UPRIGHT (22) es shown on drewing.
/ / / / Sfep 1 4 A. Affach four PARAGLIDE STRIPS /50) inside fhe end of fhe RECEIVING TUBE (17), and four PARAGLIDE STRIPS (50) outside the end of |he PRESS ADJUSTMENT TUBE I12) using following steps: *Thoroughly clean all surfaces where the PARAGLIDE STRIPS (50 / are to be aftached.
S]ep 1 5 A. B. @’~"-/2 X 3-1/2" /p"~ H/-’-P ~’L"~ IMPORTANT DO NOT OVERTIGHTEN 1 IN. NUTS, // Insert two 3/4 IN. FLANGE BEARINGS (9.3) into the PRESS ARM (2) as shown on the drawing. Hold the PRESS ARM (2) between the REAR and MIDDLE UPRIGHTS as shown in on drawling, and slide the 10-1/4 IN.
Sfep 1 ~ A. SECURELY ~igh~r~ all loose frome connections made fo ~hfs palnf. ~H~ I~PORTANT .!~ TO ASSURE PROPER FUNCTION OF THE 4~5, THE LOOSE FRAME CO~C~ON5 MU~T B~ TIGHTENED iN ~F~E FOLLOWING ORDER) Tigh.ien ~h~: *REAR UPRIGHT (15) ~ fhe BASE (7) and ¢o ~he TOP ~PRESS BASE (~) ]o ]h~ REAR (15) and MIDDLE UPRIGHTS (11).
Step 1 7 A. Assemble three 2 IN. PULLEYS (43) to the L-HOOKS on the TOP BOOM (5), us shown, and SECURE piece with two 1/4 IN. CAP NUTS (87). 1/2 I 1/2 I 1/2 2 I 1 ~ I I I Step 1 8 A. SECURELY assemble the BEARING HOUSING (18) and the CENTER PULLEY BRACKET (10) fo the FRONT UPRIGHT (22) as shown oq drawing, using two 1,/2 X 3-1/2 IN.
Step 1 9 A. LOOSELY assemble two 3-1/2 X 1 IN. PULLEYS (100) and two 2-3/8 IN. CABLE RETAINING CLIPS (62) to the CENTER PULLEY BRACKET (10) using two .5/8 X 2 IN. BOLTS (76), two 3/8 IN. WASHERS (69), and two 5/8 LOCK NUTS (91). (NOTE: THIS CONNECTION WILL BE TIGHTENED AFTER THE CABLE HAS BEEN ROUTED) I I Step 20 A.
L ~3/8 X 3" Step 21 A. Pre-assemble the PRESS BACK SUPPORT (5) using the following steps: *Att(]ch eight PARAOLIDE STRIPS (50) to the PRESS BACK SUPPORT (5) using the following steps: *Thoroughly clean all surfaces where the PARAGLIDE ~;TRIPS (50) ore "~o be attached.
× 3-]./2" A. Inserf ~wo I/2 IN. FLANGE BEARINGS (95) into ~he PRESS SUPPORT TUBE 18) as shown. SECURELY assemble the PRESS BACK SUPPORT (3) fo the PRESS SUPPORT TUBE (8) as shown drawing, using one 1/2 X 5-1/2 IN. BOLT (68), fwo 1/2 IN. WASHERS (65), and one 1/2 LOCK NUT (gO).
CABLE GUIDE PEC DEC CABLE STAMPED PART NUMBER 6555601 // 77 5/8 CABLE /STAMPED PART NUMBER 65358O1 / 66 I/4 CABLE S STAMPED PART NUMBER 6535901 // 153 MULTI-PRESSCABLE I’ STAMPED PART NUMBER 6556001 / .
S~ep 1 To assemble the D-RING CABLE (115), follow the cable routin# as shown, and use the follow!ng steps: *SECURELY assemble the D-RING CABLE (115) to the WEIGHT STACK SHAFT (104) of the HEAD PLATE (10.5) as shown. *Route the CABLE (115) up cmd over the two PULLEYS in the LAT BOOM (5) aboYe the WEIGHT STACK.
LAT CA]~LE NOTD MAKE SURE CABLE RUNS OVER OVER THE TOP OF THE BOLTS, (CONTINUED FROM PREVIOUS PAGE) *Run the LAT CABLE (112) through fhe BASE PULLEY (~s shown in druwing detoil. *Run the LAT CABLE (112) through fhe hole of the D-RING (28) c~s shown, at|~ch one KEYHOLE CLEVIS (61) to the end of the LAT CABLE (112).
MULTI-PRE~g CABLE Step 5 A. To assemble the MULTI-PRESS CABLE (113), follow the cable routing diagram shown in drawing and use the following steps: *AHach one SNAP LINK I55) fo the ball end of the MULTI-PRESS CABLE (115 / . *Run the MULTI-PRESS CABLE (115) through the hole of the D-RING /28) as.
S|ep 4 A. To ~ssemble the PEC DEC CABLE (110), follow the cobble routing diagram on drawing, and use the following steps: ~Assemble each end of the PEC DEC CABLE (110) to the PEC CAMS (9). *~Drope the CABLE (110) over the ~PULLEYS on the CENTER PULLEY BRACKET (10).
ii III 318 X 2-114" / (CONTINUED FROM PREVIOUS PAGE.) ~ake a loop with the AB CABLE (t11) and LOOSELY assemble two 5-1/4 IN, PLATES (26) and ‘5-1/2 X 1 IN. PULLEYS (100) to the AB CABLE (111) using two 5/8 X 2-1/4 IN. BOLTS (71), ‘5/B IN. WASHERS (69), and two .
I I I I I I_AT CABLE~,~----~-"- | | EXTENSION (6535901) ~~~ CABLE (65690(21), MULti-PRESS CABLE (6536001) Step 5 A. SECURELY affach ~he LEG CABLE to the LEG CURL/EXT (23) using one 5/8 X 1 IN. BOLT (74), ~wo .5/8 IN. WASHERS (69), and one 5//8 IN.
LEG CURL/EXTENS[rlN CABLE (6569001) MULTI-PRESS CABLE (6536001)t Step 6 A. AHach ].hree SHOCK CORDS (48) to ].he KEYHOLE CLEVIS (61) Bo on ].he end of each CABLE as shown. Rou].e the SHOCK CORDS (48) up and around the pre-determ;ned 2 IN. PULLEYS (43) above D-RING (28) und down fo the BASE (7).
Step 7 A. AUc~ch ~he LAT BAR (6) to the SNAP LINK (5.5). on fhe end of ~he LAT CABLE (6) as shown on drawing. TOP BO 0 M’---~ S|ep B A. SECURELY attach the FRONT (.58) and fhe REAR SHROUD (57) to the BASE and fhe TOP BOOM usfng eighf .3/8 X 1 IN. BUTTON HEAD CAP SCREWS (78).
Een belangrijk punt na aankoop van elk apparaat ParaBody 425 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ParaBody 425 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ParaBody 425 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ParaBody 425 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ParaBody 425 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ParaBody 425 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ParaBody 425 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ParaBody 425 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
