Gebruiksaanwijzing /service van het product 777101 van de fabrikant ParaBody
Ga naar pagina of 28
1 777101 GYM SYSTEM 1 CLASS H PAR T # 7017401 REV . F V ersion: 777101 Revision: 06/1 1/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 777 Gym System. Please read these instructions thoroughly and keep them for future reference.
Minimum Required Usable S p ace Length = 90 inches (229 cm) 7’ 6” Width = 103 inches (262 cm) 8’ 7” Height = 84 inches (213.5 cm) 7” 1 Square = 1’ X 1’ 4 Length = 90 inches (229 cm) 7’.
3 P AR TS LIST 5 PA R T # 70077 70076 70058 70014 70015 70017 70019 70056 70067 69408 69885 69954 69957 70082 70083 69947 6194601 6816501 7016902 7016901 6939202 6382301 69537 3221702 6978101 7095701 .
FIGURE 1 6 STEP 1: • LOOSEL Y assemble two BASE PLA TES (1 1) to the BASE (1) and the UPRIGHT (2) using four 3/8 X 3-3/4” BOL TS (57) and four 3/8” LOCK NUTS (63).
7 FIGURE 3 STEP 3: FIGURE 2 • Insert two WEIGHT PLA TE BUSHINGS (22) into each of the fifteen WEIGHT PLA TES (21) as shown in FIGURE 2. STEP 2: • Slide the WEIGHT PLA TE SHAFT (26) thru the hole in the HEAD PLA TE(23), and lock in place using one E-RING (24) as shown in FIGURE 3.
FIGURE 4 STEP 4: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Insert two GUIDE RODS (18) into the BASE (1) as shown on FIGURE 4. (NOTE: If the 777 SHROUD OPTION was pur - chased, place the GUIDE RODS (18) through the BOTTOM SHROUD BRACKET (71) and into the BASE (1) as shown in FIGURE 4.
9 STEP 5: • Swing the GUIDE RODS (18) into the guide rod bushings in each of the RIGHT and LEFT UPRIGHT PLA TES (14 & 15) as shown in FIGURE 5. • LOOSEL Y assemble the RIGHT and LEFT UPRIGHT PLA TES (14 & 15) to the UPRIGHT (2) using three 3/8 X 3-3/4” BOL TS (57) and three 3/8” LOCK NUTS (63).
10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 7: STEP 8: • SECUREL Y assemble one SEA T P AD (16) to the SEA T ADJUST (3) using two 3/8 X 2-3/4” BOL TS (55) and two 3/8” W ASHERS (64).
11 FIGURE 9 STEP 9: 40 2 3 43 42 • Securely assemble one SPRING PIN ASSEMBL Y (40) and one 3 PRONG KNOB (43) to the FRONT UPRIGHT (2) as shown. • Apply eight P ARAGLIDES (42) to the INSIDE of the tube on the UPRIGHT (2) and on the OUTSIDE of the SEA T ADJUST (3) as shown.
12 STEP 1 1: • Assemble two V -PULLEY PLA TES (12) and two 4-1/2” V -GROOVE PULLEYS (39) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOL TS (55) . See FIGURE 11 .
13 STEP 13: STEP 14: FIGURE 13 • Assemble one 3-1/2” PULLEY (37) to the BOOM PLA TES (14 & 15) using one 3/8 X 3-3/4” BOL T (57), two 3/8 X 1” SP ACERS (51) and one 3/8” LOCK NUT (63).
14 STEP 15: FIGURE 15 9 37 29 51 3/8 X 3-3/4” 57 2 63 • Assemble one 3-1/2” PULLEY (37) to the BOOM PLA TES (14 & 15) using one 3/8 X 3-3/4” BOL T (57), two 3/8 X 1” SP ACERS (51) and one 3/8” LOCK NUT (63). See FIGURE 15. (Note: Loop the WEIGHT ST ACK CABLE around the PULLEY prior to assembling to the BOOM PLA TES.
15 STEP 17: FIGURE 17 • Securely assemble the ball end of the LEG CABLE (30) and one 3-1/2” PULLEY (37) to the LEG PEDEST AL (8) using two 3/8 X 3-3/4” BOL TS (57), two 3/8” X 1-1/16” FLANGE SP ACERS (49), two 3/8” W ASHERS (64), and two 3/8” LOCKNUTS (63).
16 STEP 18: STEP 19: FIGURE 18 FIGURE 19 • Screw the threaded end of the LEG CABLE (30) into the end of the PULLEY BRACKET (9). See FIGURE 19. • Assemble one 3-1/2” PULLEY (37) to the PULLEY PLA TES (10) using one 3/8 X 1- 3/4” BOL T (53) and one 3/8” LOCK NUT (63) as shown in FIGURE 18.
17 STEP 20: FIGURE 20 • Assemble one V -PULLEY (39) to the LEFT ARM SUPPOR T (5) using one 3/8 X 2-3/4” BOL T (55) and one 3/8” LOCK NUT (63). See FIGURE 20. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the LEFT ARM SUPPOR T .
18 STEP 22: FIGURE 22 STEP 21: FIGURE 21 • Assemble two 3-1/2” PULLEYS (37) to the BASE PLA TES (11) using two 3/8 X 3-3/4” BOL TS (58), one 3/8 X 1” SP ACER (51) and two 3/8” LOCK NUTS (63). See FIGURE 21. (Note: Loop the ARM CABLE (31) around the PULLEYS prior to assem- bling the PULLEYS.
19 STEP 23: FIGURE 23 38 39 6 31 63 3/8 X 2-3/4” 55 4 • Assemble one V -PULLEY (39) to the RIGHT ARM SUPPOR T (4) using using one 3/8 X 2-3/4” BOL T (55) and one 3/8” LOCK NUT (63). See FIGURE 23. (Note: Loop the ARM CABLE around the PULLEY prior to assembling the RIGHT ARM SUPPOR T .
20 STEP 24: FIGURE 24 • SECUREL Y tighten all loose frame connections as shown in FIGURE 24! TIGHTEN! TIGHTEN! TIGHTEN! TIGHTEN! 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! TIGHTEN!.
21 STEP 25: FIGURE 25 2 16 64 • SECUREL Y assemble one SEA T P AD (16) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOL TS (55) and two 3/8” W ASHERS (64). See FIGURE 25. • Assemble two ROLLER P ADS (17) to the LEG PEDEST AL (8) using one 3/4 X 17” TUBE (52) and two 3/4” ST ARLOCK COLLARS (44) as shown in FIGURE 26.
22 • Assemble two 14-1/2” SEWN HANDLES (19) to the ARM CABLE (31) using two SNAP LINKS (41) as shown in FIGURE 27. STEP 27: FIGURE 27 32 41 20 31 41 19 • Assemble two 7-1/2” SEWN HANDLES (20) to the BOOM CABLE (32) using two SNAP LINKS (41) as shown in FIGURE 27.
23 FIGURE 28 ADJUSTMENT • Adjustments can be made in the above locations to set the correct amount of tension in the cables. ADJUSTMENT ADJUSTMENT STEP 28: 9 23 9 • If upon completion of assembly .
FIGURE 29 24 • SECUREL Y assemble the TOP SHROUD BRACKET (70) to the RIGHT and LEFT UPRIGHT PLA TES (14 & 15) using two 3/8 X 2-1/2” BOL TS (74) and two 3/8” LOCK NUTS (75) as shown in FIGURE 29.
FIGURE 30 25 STEP 30: • This completes the assembly of the 777 SHROUD OPTION. 72 3/8 X 1” BUTTON HEAD 68 73 69 • SECUREL Y assemble the LEFT SHROUD (68) and RIGHT SHROUD (69) to the T OP (70) and BOTT OM (71) SHROUD BRACKETS using eight 3/8 X 1” BUTTON HEAD BOL TS (72) and eight 3/8” BLACK SAE W ASHERS (73) as shown in FIGURE 30.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 26 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
27 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
Een belangrijk punt na aankoop van elk apparaat ParaBody 777101 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ParaBody 777101 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ParaBody 777101 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ParaBody 777101 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ParaBody 777101 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ParaBody 777101 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ParaBody 777101 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ParaBody 777101 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
