Gebruiksaanwijzing /service van het product 893103 van de fabrikant ParaBody
Ga naar pagina of 20
Serious Ste~ -893103 PRO SYSTEM II Illl Illl ASSEMBLY INSTRUCTIONS Part # 6753901 1 l~evision:10F27/97.
I I ,M2ORTANT NOTESJ WELCOME TO THE WORLD OF Please note: * Thank you for purchasing the Parabody 893103 PRO SYSTEM. Please :read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, leve surface to assure its proper function.
1 2 4 6 7 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PART # 656603 6566702 6546302 6566903 6567002 6581102 6569802 6567302 6567502 6567803 6516502 6568102 6568303 6568603 6568703 6370403 .
, FIGURE 2 STEP 2: ¯ Assemble two COVER CAPS (48) to the ends of the BENT TUBE (4) as shown in HGURE ¯ Insert two 2" SQ. END CAPS (47) to the ends of the LrpRIGHT FRAME (1) as shown in FIGLTRE .
3~8 X 2-3/4" FIGURE 3 STEP 3: ¯ LOOSELY assemble the UPRIGHTS (5) to the BENT TUBE (4) using four 3/8 X 2-3/4" BOLTS (28) and four 3/$" N’U~S (36) as shown in FIGURE 3.
FIGURE 4 STEP 4: ¯ Attach ten 1-1/2 X 3/4" GLIDES (54) to both SAFETY RAILS (9) as shown in FIGURE ¯ SECURELY assemble one SPRING PIN ASSEMBLY (40) to both SAFETY RAILS (9) as shown in FIGURE ¯ Thread one TH’UMBSC1LEW (43) into both SAFETY RAILS (9) as shown in FIGURE FIGURE 5 STEP 5: ¯ Apply eight 1" SQ.
FIGURE 6 STEP 6: Pull back the SPRING PIN and slide the SAFETY RAILS (9) over the UPRIGHTS (5) until the S]?I~[NG PIN is engaged in ftrst hole. ¯ Slide the CARRIAGE (3) over the LrpRIGHT FR.
Rout over bolts. l 1/2 X3" 1/2 X 3" I FIGURE 8 STEP 8: - ¯ LOOSELY assemble Lhc TOP BOOM (2) to the UPRIGHT FRAME (I) using two I/2 X 3" BOLTS (27), one 3/8 X BOLT (25), one I/2" LOCK WASHER (32), I/2" WASHE R (30), one I/ 2" L OCKNU T (34), and on e 3/ 8" L OC~-I " (36) as shown ~ FIGUI~ 8.
STEP 10: ¯ Assemble two 4 X 7" ROLLER PADS (20) the SWIVEL KNEE SUPPORT (10) using two STARLOCK COLLARS (49) as shown FIGUR~ I0. FIGUR~ 10 FIGURE 11 1/2 X 3-1/4" ~ }1/2" LOW HT. LOCK NUT STEP 11: ¯ SECURELY assemble the SWIVEL KNEE SUPPORT (10) to the UPRIGHT FRAME (1) using one 1/2 X 3-1/4" BOLT and one 1/2" LOW HT.
FIGURE 12 STEP 12: ¯ LOOSELY assemble two 3-1/2" PULLEYS (23) and two CABLE RETAINING CLIPS (56) to the £.~q’I’ER PULLEY BRACKET (16) using two 3/8 X 2" BOLTS (29), two 3/8" WASHERS (31), and two 3/8" LOCKNUTS (36). See FIGURE STEP 13: Assemble two 2" SQ.
FIGURE 14 STEP 14: ¯ SECURELY assemble the BEARING HOUSING (13) and the CENTER PULLEY BRACKET (16) to the UPRIGHT FRAM~ using two 1/2 X 3-1/4" BOLTS (26) and two 1/2" LOCKN’t~S (34) as shown in FIGURE STEP 15: ¯ Insert fot~ 2" SQ. END CAPS (47) into the LEFT (15) & RIGHT PEC ARMS as shown in FIGURE 15.
~FIGURE 16 STEP 17: ¯ SECURELY assemble BACK PAD (19) to the UPRIGHT FRAME (1) using two 3/8 X 2-3/4" BOLTS (28) and two 3/8" LOCK WASKERS (33) as shown in FIGURE 17.
LAT CABLE &~ LOW ROW CABLE C) i i 893103 CABLE DIAGRAM ¯ Refer to the 839103 CABLE DIAGRAM for help with STEPS 17-27 13.
STEP 19: Place one 3-1/2" PULLEY (23) into the loop the CABLE (25) below the first and second PULLEY of the TOP BOOM (2) as shown FIGURE 19. LOOSELY assemble t~’o 1-3/4 X 5-I/4" PLATES (I 7) to each side of the PULLEY using one 3/8 X 2" BOLT (29) and one 3/8" LOCK.
FIGURE 20 318 X 2-3/4" 318 X 2" STEP 20: ¯ SECURELY assemble one 3-1/2" PULLEY (23) and one CABLE RETAINING CLIP (56) to the plate on the UPRIGHT FRAME (1) using one 3/8 X 2" BOLT (29), one 3/8" WASHER (31), and one 3/8" LOCK NUT (361,.
STEP 22 Wrap the PEC DEC CABLE (24) around one 3-1/2" PULLEY (23) and assemble the PULLEY to the PULLEY BRACKET (1 l) using one 3/g X 2" BOLT (29) and one 3/8" LOCKNUT (36) as shown in HGUR~ 22. 3 FIGURE 22 FIGURE 23 STEP 23: ¯ Insert each end of PEC CABLE (24) into the bushings on the cams of the LEFT (15) & RIGHT (].
FIGURE 24 STEP 24: ¯ Route the CABLE (25) under the 3-1/2" PULLEY in the slot on the FRONT UPRIGHT (1) and around the 3-1/2" PULLEY shosrn on FIGU’KE 24.
3/8X2" FIGURE 25 / / STEP 25: ¯ Loop the CABLE (25) around one 3-1/2" PULLEY (23) and LOOSELY assemble PULLEY to the 1-3/4 X 5-1/4" PLATES (17) using one 3/8 X 2" BOLT (29) and one 3/8" LOCK NUT (36).
FIGURE 26 ,, STEP 26: ¯ Route CABLE (25) around PULLEY and undcx the CABLE RETAINING CLIP on FRONT UPILIGttT (1) a.~ sho~’n in FIGURE 26. ¯ Attach the CABLE (25) to the PULLEY BRACKET (11) using one QUICK LINK (38) as shown in HGURE ¯ SECURELY tighten the two PULLEYS assembled between the two 1-3/4 X 5-1/4" PLATES (17).
FIGURE 27 STEP 27: ¯ Attach two I X 8" GRIPS (50) to the LAT BAR (6) and two 1 X 8" GRIPS (50) to the LOW ROW B~kR (18) as FIGURE 27. (TIP: Spray window cleaner on the inside of the grip to help ease assembly.) ¯ Attach the LOW ROW BAR (18)to the CABLE (25) using two 5/16" SNAP LINKS (37) and one C~-IAIN (39) as FIGURE 27.
Een belangrijk punt na aankoop van elk apparaat ParaBody 893103 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ParaBody 893103 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ParaBody 893103 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ParaBody 893103 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ParaBody 893103 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ParaBody 893103 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ParaBody 893103 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ParaBody 893103 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
