Gebruiksaanwijzing /service van het product GS4 van de fabrikant ParaBody
Ga naar pagina of 27
1 GS4 GYM SYSTEM CLASS H PAR T # 7657901 REV . A Revision: 08/12/05 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULES ! 1. Before u sing, read al l the w arnings and in structions on the use of this machine. Use only for in tended exercise. DO NOT mo dify the machine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody GS4 Gym System. Please read these instructions thoroughly and keep them for future reference.
COMPONENTS P AR TS LIST KEY A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ 4 PA R T # ACU04-1512 ACU04-1511 ACU02-1492 ACU02-1489 ACU02-1490 ACU.
FIGURE 1 5 STEP 1: 19 6 L 3/8 X 3” 8 19 C • LOOSEL Y assemble two BASE PLA TES (C) to the FRAME (A) and BASE (B) using three 3/8 X 3-3/4” BOL TS (6) and four 3/8” LOCK NUTS (19).
6 FIGURE 3 FIGURE 2 • CHECK THA T THE HEADPLA TE AND WEIGHT PLA TES ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3.
FIGURE 4 B AE 29 AD STEP 4: 7 GS4 SHROUD BRACKET OPTION ONL Y AF ** AQ • Insert two GUIDE RODS (AC) into the BASE FRAME (B) as shown on FIGURE 4. (NOTE: If the GS4 SHROUD OPTION was purchased, place the GUIDE RODS (AC) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the BASE FRAME (B) as shown in FIGURE 4.
8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 5: • Carefully slide the RIGHT (N) and LEFT (M) REAR UPRIGHTS over the GUIDE RODS (AC ) as shown in FIGURE 5 and SECUREL Y assembly the RIGHT (N) and LEFT (M) REAR UPRIGHTS to the BASE (B) using four 3/8 X 3-3/4” BOL TS (6), four 3/8” W ASHERS (18) and two 3/8” LOCK NUTS (19) as shown in FIGURE 5.
FIGURE 6 STEP 6: 9 19 AC 29 D E A 3/8 X 3-3/4” 6 • SECUREL Y assemble the LEFT (D) and RIGHT (E) BOOM PLA TES to the FRAME (A) using two 3/8 X 3-3/4” BOL TS (6) and two 3/8” LOCK NUTS (19).
10 • Slide the LEFT (F) and RIGHT (G) PEC FL Y ARMS over the BASE (B) as shown in FIGURE 7. FIGURE 7 STEP 7: B 17 F I G I DO NOT TIGHTEN YET 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y assemb.
STEP 8: • SECUREL Y assemble the PEC PLA TE (O) to the BASE (B) using two 3/8 X 2-3/4” BOL TS (9), one 3/8 X 4” BOL T (5), two 3/8” W ASHERS (18) and three 3/8” LOCK NUTS (19) as shown in FIGURE 8.
12 STEP 10: • SECUREL Y assemble one SEA T/BACK P AD (AI) to the SEA T ADJUST (J) using two 3/8 X 2” BOL TS (10) and two 3/8” W ASHERS (18). FIGURE 10 J AI • CAREFULL Y insert the SEA T ADJUST ASSEMBL Y into the FRAME (A) as shown. The SEA T height can be adjusted using the PLUNGER PIN.
13 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 12: • SECUREL Y tighten the two 5/16 X 1/4” SET SCREWS (PRE-INST ALLED)on the FRAME (A) as shown in FIGURE 12. • Insert the PRESS ARM SUPPOR T PIVOT thru the PRESS ARM SUPPOR T FRAME (X) and the FRAME (A).
SPRING PIN 3/8 X 3/4” ALLEN SCREW X H 14 STEP 13: • Insert the PRESS ARM PIVOT SHAFT thru the PRESS ARM (H) and the PRESS ARM SUPPOR T FRAME (X) and the resassemble the 3/8 X 3/4” ALLEN SCREWS and 3/8” LOCK W ASHERS to the PRESS ARM PIVOT SHAFT as shown in FIGURE 13.
3/8 X 3-3/4” 6 AM 19 A 35 26 15 STEP 14: FIGURE 14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Route the LA T CABLE (AM) through the FRAME (A) and assemble one 3-1/2” PULLEY (35) to the FRAME (A) using one 3/8 X 3-3/4” BOL T (6), two 3/8 X 1-1/16” FLANGE SP ACERS (26) and one 3/8” LOCK NUT (19).
16 STEP 15: FIGURE 15 • Route the LA T CABLE (AM) around one 3-1/2” PULLEY (35) and assemble the PULLEY to the LEFT (D) and RIGHT (E) BOOM PLA TES using one 3/8 X 3-3/4” BOL T (6), two 3/8 X 15/16” SP ACERS (24) and one 3/8” LOCK NUT (19). See FIGURE 15.
STEP 16: FIGURE 16 • Route the LA T CABLE (AM) through the PRESS ARM SUPPOR T FRAME (X) and assemble one 3-1/2” PULLEY (35) to the FRAME PRESS ARM SUPPOR T FRAME (X) using one 3/8 X 8” BOL T (3), two 3/8” W ASHERS (18), two 3/8 X 1-1/4” SP ACERS (25) and one 3/8” LOCK NUT (19).
STEP 17: FIGURE 17 18 • Route the LA T CABLE (AM) around one 4-1/2” PULLEY (36) and assemble the PULLEY to the LEFT (D) and RIGHT (E) BOOM PLA TES using one 3/8 X 3-3/4” BOL T (6), one LONG “L” CABLE BRACE (S), one 1” SP ACER (24) and one 3/8” LOCK NUT (19).
STEP 18: FIGURE 18 19 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Route the PEC FL Y CABLE (AP) around one 4-1/2” PULLEY (36) and assemble the 4-1/2” PULLEY (36) to the DOUBLE FLOA TING PULLEY BRACKET (AA) using one 3/8 X 1-3/4” BOL T (1 1) and one 3/8” LOCK NUT (19).
STEP 19: FIGURE 19 20 • Route the hook end of the GUIDE CABLE (AO) thru the CABLE GUIDE (23) then SECUREL Y assemble the hook end of the GUIDE CABLE (AO) to the BASE using one 3/8 X 3-3/4” BOL T (6), one 3/8” W ASHER (18)and one 3/8” LOCK NUT (19) as shown in FIGURE 19.
STEP 20: FIGURE 20 21 • Route the large ball end of the LOW CABLE (AN) around one V - PULLEY (37) and assemble the PULLEY to the FRAME (A) using two 3/8 X 3-3/4” BOL TS (6), two19/32” FLANGE SP ACERS (28), two 3/8” W ASHERS (18) and two 3/8” LOCK NUTS (19) as shown in FIGURE 20.
STEP 21: FIGURE 21 22 • Route the LOW CABLE (AN) around one 3-1/2” PULLEY (35) and assemble the PULLEY to the PULLEY BRACKET (Z) using one 3/8 X 1-3/4” BOL T (11) and one 3/8” LOCK NUT (19) as shown in FIGURE 21.
STEP 22: FIGURE 22 • Assemble one 3-1/2” PULLEY (35) to the FOOT PLA TE (L) using one 3/8 X 3” BOL T (8), two STEP SP ACERS 11/16” (27) and one 3/8” LOCK NUT (19).
FIGURE 23 AK AG AH 24 22 ADJUSTMENT • If upon completion of assembly , the HEAD PLA TE (AF) does not sit on top of the first WEIGHT PLA TE, push the HEAD PLA TE (AF) down, insert the WEIGHT SELECTOR PIN and perform several repetitions at the press station.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 25 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
26 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED W ARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
Een belangrijk punt na aankoop van elk apparaat ParaBody GS4 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ParaBody GS4 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ParaBody GS4 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ParaBody GS4 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ParaBody GS4 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ParaBody GS4 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ParaBody GS4 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ParaBody GS4 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
