Gebruiksaanwijzing /service van het product GS6 van de fabrikant ParaBody
Ga naar pagina of 33
1 GS6 GYM SYSTEM CLASS H PAR T # 7359601 REV . A Revision: 11/06/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULES ! 1. Before u sing, read al l the w arnings and in structions on the use of this machine. Use only for in tended exercise. DO NOT mo dify the machine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody GS6 Gym System. Please read these instructions thoroughly and keep them for future reference.
COMPONENTS P AR TS LIST PA R T # ACU04-1528 ACU02-1526 ACU02-1451 ACU04-1529 ACU04-1530 ACU04-1532 ACU04-1533 ACU04-1534 ACU04-1535 ACU04-1536 ACU02-1523 ACU02-1071 ACU04-1528 ACU02-1524 ACU04-1539 AC.
HARDW ARE P AR TS LIST PA R T # ACUDA1E012101213NB ACUDA1E01271413NB ACUDA1E01260013NB ACUDA1E01241413NB ACUDA1C01209213NB ACUDA1E01231213NB ACUDA1E01230013NB ACUDA1C01210413NB ACUDA1E03853416NB ACUDA.
FIGURE 1 6 STEP 1: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y assemble the REAR FRAME (D) to the BASE (A) using two 3/8 X 3-3/4” BOL TS (1 1), two 3/8” W ASHERS (23) and two 3/8” LOCK NUTS (28) as shown in FIGURE 1.
FIGURE 2 STEP 2: • LOOSEL Y assemble two BASE PLA TES (B) and the FOOT ASSEMBL Y (F) to the BASE (A) using two 3/8 X 4” BOL TS (10) and two 3/8” LOCK NUTS (28).
FIGURE 3 8 STEP 3: E 3/8 X 3-3/4” 11 B 28 • SECUREL Y assemble the FRONT FRAME (E) to the BASE PLA TES (B) using two 3/8 X 3-3/4” BOL TS (1 1) and two 3/8” LOCK NUTS (28) as shown in FIGURE 3.
9 FIGURE 5 FIGURE 4 • CHECK THA T THE HEADPLA TE AND WEIGHT PLA TES ARE ASSEMBLED AS SHOWN IN FIGURES 4 & 5.
FIGURE 6 STEP 6: 10 • Insert two GUIDE RODS (AI) into the REAR FRAME (O) as shown on FIGURE 6. (NOTE: If theGS-6 SHROUD OPTION was purchased, place the GUIDE RODS (AI) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the REAR FRAME (D) as shown in FIGURE 6.
FIGURE 7 STEP 7: 11 • Swing the GUIDE RODS (AI) into the guide rod bushings in the RIGHT TOP ASSEMBL Y (Y) as shown in FIGURE 7. • LOOSEL Y assemble the RIGHT TOP ASSEMBL Y (Y) and the LEFT T OP PLA TE (Y) to the REAR FRAME (D) and the FRONT FRAME (E) using three 3/8 X 3-3/4” BOL TS (1 1 ) a nd three 3/8” LOCK NUTS (28).
FIGURE 8 12 STEP 8: • SECUREL Y assemble the PEC FL Y MOUNT (U) and BACKING PLA TE (V) to the FRONT FRAME (E) using two 1/2 X 3” BOL TS (7) and two 1/2” LOCK NUTS (26) as shown in FIGURE 8.
13 FIGURE 9 STEP 9: • Assemble the RIGHT PEC FL Y ARM (T) and LEFT PEC FL Y ARM (S) to the PEC FL Y MOUNT (U) using two 1/2 X 92mm BOL TS (5), two 3” LONG SP ACERS (35), four SHIM W ASHERS (25), two 1/2” LOW HEIGHT LOCK NUTS (27) and four RH CAPS (45) as shown in FIGURE 9.
14 STEP 10: FIGURE 10 • Assemble the PEC HANDLE (P) to the LEFT PEC FL Y ARM (S) using one 1/2 X 3/4” BUTTON HEAD BOL T (20) and on 1/2” W ASHER (21) as shown in FIGURE 10.
15 STEP 1 1: FIGURE 1 1 • CAREFULL Y slide the SEA T ADJUST (M) onto the SEA T FRAME (AF) as shown. The SEA T can be adjusted and tightened using the PLUNGER PIN.
16 FIGURE 13 STEP 14: FIGURE 14 STEP 13: • SECUREL Y assemble the PIVOT ASSEMBL Y (AG) to the SEA T FRAME (AF) using two 3/8 X 2-3/4” BOL TS (15), two 3/8” W ASHERS (23) and two 3/8” LOCK NUTS (28) as shown in FIGURE 13.
17 FIGURE 15 STEP 15: • Assemble the SEA T SUPPOR T BRACKET (O) to the PIVOT ASSEMBL Y (AG) and the BENCH TUBE (J) using two 1/2 X 6” BOL TS (3) and two 1/2” LOW HEIGHT LOCK NUTS (27). (Note: T ighten this connection enough to remove excess play yet allow the BENCH TUBE to r otate freely .
18 FIGURE 17 STEP 17: • Assemble the LEG PEDEST AL (AD) to the SEA T FRAME (AF) using one 1/2 X 104mm BOL T (8), two SHIM W ASHERS (25), one 1/2” LOCK NUT (27) and two RH CAPS (45). (Note: Tighten this connection enough to remove excess play yet allow the LEG PEDEST AL to rotate fr eely .
• Assemble two 4 X 7” ROLLER P ADS (AS) to the LEG PEDEST AL (AD) using two PLASTIC W ASHERS (48) and two ST ARLOCK COLLARS (44) as shown in FIGURE 19. • Assemble two 4 X 7” ROLLER P ADS (AS) to the SEA T FRAME (AF) using one 3/4 X 17-1/2” TUBE (AB), two PLASTIC W ASHERS (48) and two ST ARLOCK COLLARS (44) as shown in FIGURE 19.
20 FIGURE 20 STEP 21: FIGURE 21 STEP 20: • Insert one 3/4” X 6” SHAFT (36) into the tube on the REAR FRAME (D) as shown. 26 D 1/2 X 7-1/4” 2 D I 26 1/2 X 10-1/2” 1 • SECUREL Y assemble the.
FIGURE 22 STEP 22: 21 26 G AE 1/2 X 3-1/2” 6 • SECUREL Y assemble the PRESS ARM ADJUSTMENT (G) to the PRESS LOAD ARM (AE) using one 1/2 X 3-1/2” BOL T (6) and one 1/2” LOCK NUT (26) as shown in FIGURE 22.
FIGURE 24 22 STEP 24: R 27 I Q • Assemble the RIGHT PRESS ARM HANDLE (R) to the PRESS ARM (I) using one 25/32” BUMPER (AO) and one 1/2” LOW HEIGHT LOCK NUT (27) as shown in FIGURE 24. (NOTE: Tighten 1/2” LOW HEIGHT LOCK NUT (27) to remove excess play yet allow the RIGHT PRESS ARM HANDLE (R) to rotate freely .
STEP 25: FIGURE 25 • SECUREL Y assemble two 2-29/32” PLASTIC SLEEVES (47) to the BASE PLA TES (B) using two 3/8 X 3-3/4” BOL TS (11) and two 3/8” LOCK NUTS (28) as shown in FIGURE 25(b) • SE.
24 STEP 26: • Assemble two 3-1/2” PULLEYS (49) to the RIGHT T OP ASSEMBL Y (X) using two 3/8 X 2” BOL TS (16), two L CABLE RET AINER (AA) and two 3/8” LOCK NUTS (28) as shown in FIGURE 26(b) • Screw the long threaded end of the LA T CABLE (A V) into the end of the HEAD PLA TE (AK) .
STEP 27: FIGURE 27 • Route the threaded end of the LOW CABLE (A W) thru theSEA T FRAME (AF) and assemble the swivel end of LOW CABLE (A W) to the LEG PEDEST AL (AD) using one 3/8 X 3-1/4” BOL T (13), two 15/16” FLANGE SP ACERS (41) and one 3/8” LOCK NUT (28).
STEP 28: FIGURE 28 • Assemble one 3-1/2” PULLEY (49) to the BASE PLA TES (B) using one 3/8 X 4” BOL T (10), one 3/8 X 15/16” SP ACER (30) and one 3/8” LOCK NUT (28). See FIGURE 28(a) (Note: Loop the LOW CABLE (A W) ar ound the PULLEY prior to assembling the PULLEY to the BASE PLA TES.
STEP 29: FIGURE 29 • Assemble one 3-1/2” PULLEY (49) to the bracket on the BASE (A) using one 3/8 X 2-1/4” BOL T (52),one 3-1/2” PULLEY GUARD (C), one 3/8” SP ACER (31) and one 3/8” LOCK NUT (28). See FIGURE 29(a) (Note: Loop the LOW CABLE (45) around the PULLEY prior to assembling the PULLEY to the BASE .
STEP 30: FIGURE 30 28 • Securely assemble the PEC FL Y CABLE (AX) to the RIGHT PEC FL Y ARM (T) as shown in FIGURE 30(a) • Assemble one 3-1/2” PULLEY (49) to the PEC FL Y MOUNT (13) using one 3/8 X 2-3/4” BOL T (15), one 3-1/2” PULLEY GUARD (C) and one 3/8” LOCK NUT (28).
29 • Securely assemble the ball end of the AB CRUNCH CABLE (A Y) and one 4-1/2” V -PULLEY (51) to the FRONT FRAME (E) using two 3/8 X 3-3/4” BOL TS (1 1), two 3/8 X 19/32” FLANGE SP ACERS (42), two 3/8” W ASHERS (23) and two 3/8” LOCKNUTS (28).
30 FIGURE 32 AT 39 AM ADJUSTMENT • If upon completion of assembly , the HEAD PLA TE (AK) does not sit on top of the first WEIGHT PLA TE, push the HEAD PLA TE (AK ) down, insert the WEIGHT SELECTOR PIN and perform several repetitions at the press station.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 31 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
32 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
Een belangrijk punt na aankoop van elk apparaat ParaBody GS6 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ParaBody GS6 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ParaBody GS6 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ParaBody GS6 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ParaBody GS6 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ParaBody GS6 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ParaBody GS6 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ParaBody GS6 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
