Gebruiksaanwijzing /service van het product MDR8 van de fabrikant Samson
Ga naar pagina of 24
MDR Series Mixers EIGHT CHANNEL MIXER WITH 24BIT DIGIT AL EFFECTS AND HARD DISK MODE.
Safety Instructions/Consignes de sécurité/Sicherheitsvor kehrungen/Instr ucciones de seguridad ACHTUNG: Um die Gefahr eines Brandes oder Stromschlags zu verringern, soll- ten Sie dieses Gerät weder Regen noch Feuchtigkeit aussetzen.Um die Gefahr eines Stromschlags zu verringern, sollten Sie weder Deckel noch Rückwand des Geräts entfernen.
T able of Contents Introduction 2 MDR8 Features 3 Front and Rear P anel Lay out 4 Front and Rear P anel Controls 5 Controls and Functions Mono Input Channel Section 6–7 Master Section 8–9 MDR8 Inp.
2 Congratulations on your purchase of the Samson MDR8 mixer! The MDR8 is an eight channel mixer, with six low noise microphone pre-amps, and built-in 24 BIT DSP effects processor.
3 MDR8 F eatures The Samson MDR8, eight channel mixer with onboard 24 BIT DSP is a comprehensive, all-in-one solution for live sound, recording, fixed installation and post production applications. Here are some of its main features: • Eight Channels – Four Mic/Line plus two Stereo inputs with mic pre’s.
4 F ront and Rear P anel La yout.
5 FRONT PANEL 1 MIC/LINE – Combination Input connector for Low-Noise Microphone pre-amp and Line level inputs. 2 GAIN – Used to set the input level of the mic pre and line input. 3 CLIP – Red LED will illuminate indicating when the mic GAIN has been adjusted too high.
6 Controls and Functions MONO INPUT CHANNEL SECTION The following section details each part of the MDR8’s MONO INPUT CHANNELS including the GAIN control, 3- BAND EQ, AUX sends, RECORD, PAN and LEVEL controls.
BALANCE (Stereo Inputs Only) The MDR8’s BALANCE control is used to place or position the stereo signal into the main Left and Right MIX bus. You can move a stereo signal’s image to the left or right by setting the BALANCE control to the left or to the right.
24 BIT DIGIT AL EFFECT SECTION The MDR8 features a built-in, 24 Bit Digital Effects proces- sor with high quality, studio grade effects such as Delay, Chorus and Reverb.
9 Controls and Functions MASTER SECTION (continued) Auxiliary Returns The MDR8 has two stereo auxiliary returns, which can be accessed via the two pairs of 1/4-inch phone jacks located on the rear panel.
10 Line Level Input - Mono Input Channels Use these inputs to connect line level signal from synthesizers, drum machines, effects processors or any line-level signal. The LINE inputs have a nominal operating level of -40dB through - 10dB. TRS phone jacks (located in the center of the combie connector).
11 AUX 1 RETURN LEFT/RIGHT The AUX 1 RETURN LEFT/RIGHT are stereo inputs that are generally used to connect the outputs of an effects processor, but can also accept the sig- nal from any line level source like a keyboard, recorder and even another mixer.
Operating the MDR8 12 BASIC OPERATION The following section explains the basic operation of the MDR8. CONNECTING MICROPHONES AND INSTRUMENTS 1. Before connecting mics or instruments, make sure that the power of all your sys- tems components including the MDR8 is turned off.
Operating the MDR8 13 USING THE DIGITAL EFFECTS The MDR8 features a built-in, high quality, 24 BIT Digital Signal Processor offering studio grade effects. The DSP features clean Delay, lush Reverbs and multi-effects such as Chorus + Delay or Chorus + Reverb.
14 Operating the MDR8 USING AN EXTERNAL EFFECT If you prefer to use an external device for effects process- ing, you can easily connect the unit using the MDR8 EFX bus disconnecting the internal DSP. Follow the simple steps below to interface your processor: 1.
15 Using The HDM (HARD DISK MODE) The MDR8 includes an exclusive HDM (HARD DISK MODE) that has been designed to interface with computer based hard disk recorders. Never before have such flexible routing and monitoring been included in such a small mixer.
16 Operating the MDR8 Using The HDM (HARD DISK MODE) Continued 3. Engage the HDM switch in the Master Section. The input channel’s REC LED will light dimly indicating the channel can be assigned to the RECORD bus. 4. Press the RECORD switch on the MDR8’s channel 7/8.
17 MDR8 Sy stem Set-Ups This system shows the MDR8 connected to a pair of powered speakers lik e the SAMSON Expedition EX20. The MONITOR OUT is connected to an exter- nal power amp , which is driving 2 monitor speak- ers.
18 MDR8 Sy stem Set-Ups This system shows the MDR8 in a recording set up with the LEFT and RIGHT C ONTROL R OOM output hooked up to powered studio monitors and the A UX 1/ Mon feed head- phone mix sent to a Samson S phone headphone amp.
19 MDR8 Wiring Guide Unbalanced 1/4” Connector XLR Balanced Wiring Guide CONNECTING THE MDR8 The are several ways to interface the MDR8 to support a variety of applications. The MDR8 features balanced inputs and outputs, so connecting balanced and unbalanced signals is possible.
20 MDR8 Specifications Frequency Response (Trim @ Min, unity gain ± 3 dB) Mic to Main 5 Hz - 54 kHz Line to Main 5 Hz - 54 kHz Aux Return to Main 5 Hz - 98 kHz Line to Aux Send 5 Hz - 57 kHz T.H.D. (Trim @ Min, +4dBu output, unity gain, 1 kHz w/30 kHz LPF) Mic/Line to Main (Mono Ch) 0.
21 Block Diagram.
Samson T echnologies Corp. 575 Underhill Blvd. P .O. Box 9031 Syosset, NY 1 1791-9031 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 516-364-3888 www .samsontech.
Een belangrijk punt na aankoop van elk apparaat Samson MDR8 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Samson MDR8 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Samson MDR8 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Samson MDR8 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Samson MDR8 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Samson MDR8 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Samson MDR8 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Samson MDR8 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
