Gebruiksaanwijzing /service van het product CO25 van de fabrikant Stanley Black & Decker
Ga naar pagina of 20
CO25 HYDRAULIC CUT -OFF SA W USER MANUAL Safety , Operation and Maintenance © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 34962 2-2015 V er-14.
2 ► CO25 User Manual DECLARATION OF CONFORMITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORMITA Hydraulic Tools _______ _________.
CO25 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► CO25 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CO25 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Review them carefully before operating the tool and before per- forming general maintenance or repairs.
6 ► CO25 User Manual • Never carry the tool or put it down while the wheel is rotating. Make sure it is completely stopped before moving your position or set the tool down. • Do not operate the tool with the wheel guard removed. • Keep the handles dry , clean and free of oil at all times.
CO25 User Manual ◄ 7 The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory . Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.
8 ► CO25 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
CO25 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
10 ► CO25 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
CO25 User Manual ◄ 1 1 PREOPERA TION PROCEDURES CHECK THE POWER SOURCE Careful inspection of the tool and hydraulic system before st ar tu p i s important for safe, reliable operation of the tool.
12 ► CO25 User Manual If excessive vibration or any other defect is detected, stop the tool immediately and determine the cause. Do not use the tool until the problem is corrected. GENERAL OPERA TION HANDHELD CONFIGURA TION: 1. Whenever possible, clamp or hold down the work and support it securely on both sides of the cut.
CO25 User Manual ◄ 13 PERIODIC MAINTENANCE For maximum performance and reliability of the tool, peri- odically check the following components. THRUST COLLAR AND INSIDE/OUTSIDE COLLAR INSPECTION Periodically inspect the thrust collar for damage when you remove the cut-off wheel (refer to Cutof f Wheel Replace- ment).
14 ► CO25 User Manual CUT OFF WHEEL REPLACEMENT 1. Move the hydraulic system control valve to the Off posi- tion. 2. Disconnect the hydraulic hoses from the tool (rst the input (supply) hose, then the output (return) hose).
CO25 User Manual ◄ 15 NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before connection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydraulic tools.
16 ► CO25 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diag- nosing faults in operation of the wrench, always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the tool as listed in the following table.
CO25 User Manual ◄ 17 Wheel Capacity ............................................................................................................................................. 14-inch/15.6 cm Weight ...............................................
18 ► CO25 User Manual For Parts to Handle Extension Kit, See Accessories on Page 17 D C B A D C B A 1 3 4 5 6 7 8 1 2 3 4 5 6 7 8 2 NOTES: HYDRAULIC TOOLS NOTE: ALL DIMENSIONS ARE GIVEN IN INCHES AND DEFINE THE FINISHED PART. TOLERANCES AND SURFACE ROUGHNESS IS SPECIFIED BELOW (EXCEPT AS NOTED): WEIGHT: LBS 49.
CO25 User Manual ◄ 19 • Denotes Part in Seal Kit Item No. Part No. Qty Description 1 001 12 1 QUAD RING* 2 00175 4 O-RING* 3 00563 1 ROLL PIN 4 00720 1 SETSCREW 5 00772 1 WOODRUFF KEY 7 01594 2 WA.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Een belangrijk punt na aankoop van elk apparaat Stanley Black & Decker CO25 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Stanley Black & Decker CO25 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Stanley Black & Decker CO25 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Stanley Black & Decker CO25 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Stanley Black & Decker CO25 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Stanley Black & Decker CO25 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Stanley Black & Decker CO25 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Stanley Black & Decker CO25 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
