Gebruiksaanwijzing /service van het product RS25 van de fabrikant Stanley Black & Decker
Ga naar pagina of 20
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 31846 8/2014 V er . 1 1 USER MANUAL Safety , Operation and Maintenance RS25 HYDRAULIC RAIL SA W.
2 ► RS25 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ ______.
RS25 User Manual ◄ 3 DECLARA TION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS .............................................................
4 ► RS25 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
RS25 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► RS25 User Manual CUTTING WHEEL SAFETY • Do not store or transport the saw with the wheel in- stalled. • Ensure that the cutting wheel is correctly mounted and tightened before use. • Operate the Rail Saw at “no load” for 30 seconds in a safe position and ensure there is no vibration or other defects detected.
RS25 User Manual ◄ 7 WHEEL SIZE RPM: SPINDLE: PRESS: BAR PSI FLOW : LPM GPM 2881 1 Information Plaque (CE models only) 05868 Abrasive Cut-Off Safety Label (14 inch models only – except CE) CA UT ION PROTECT YOUR EYES - WEAR SAFETY GOGGLES 1. Do not use damaged wheels.
8 ► RS25 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
RS25 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
10 ► RS25 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
RS25 User Manual ◄ 1 1 PRE-OPERA TION PROCEDURES CHECK HYDRAULIC POWER SOURCE 1. Using a calibrated owmeter and pressure gauge, check that the hydraulic power source develops a ow of 9–10.
12 ► RS25 User Manual OPERA TING PROCEDURES CLAMPING THE RAIL SA W TO THE RAIL 1. Observe all safety precautions. 2. Make sure the rail clamp assembly is tight to the disconnect pivot (60) by turning the handle (20) to tighten the disconnect pivot bolt.
RS25 User Manual ◄ 13 DET ACHING THE UPPER AND LOWER LINKS The upper and lower links of the rail clamp assembly can be detached from the motor mount (50) by unscrew- ing the handle (20). SA W STORAGE By disengaging the double cam (52), the rail clamp as- sembly can be rotated so that the entire saw has a atter prole for storage.
14 ► RS25 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
RS25 User Manual ◄ 15 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the grinder , always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the grinder as listed in the table.
16 ► RS25 User Manual Wheel Capacity 14 inch Model .................................................... 14 in./35.5 cm Dia. × 25.4 mm Arbor (ANSI B7.5/ISO 525, 603) 16 inch Model .............................................................. 16 in.
RS25 User Manual ◄ 17 RS25 P ARTS ILLUSTRA TION.
18 ► RS25 User Manual ITEM P ART NO. QTY DESCRIPTION 6 28181 1 BELL CRANK 15 30958 1 “D” W ASHER 20 66136 1 HANDLE WELDMENT 26 — 1 * REFER TO ITEM 131 27 30671 1 ASSIST HANDLE 28 31030 1 HANDL.
RS25 User Manual ◄ 19 ITEM P ART NO. QTY DESCRIPTION 28322 1 CE STICKER (14 IN MODEL) 127 1 1207 1 CIRCUIT “D” STICKER (14 IN MODEL) 128 2881 1 1 INFORMA TION PLAQUE (14 IN MODEL) 129 56706 1 DE.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Een belangrijk punt na aankoop van elk apparaat Stanley Black & Decker RS25 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Stanley Black & Decker RS25 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Stanley Black & Decker RS25 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Stanley Black & Decker RS25 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Stanley Black & Decker RS25 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Stanley Black & Decker RS25 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Stanley Black & Decker RS25 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Stanley Black & Decker RS25 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
