Gebruiksaanwijzing /service van het product FCB1010 van de fabrikant Behringer
Ga naar pagina of 16
Users Manual ENGLISH Version 1.4 M arch 2003 MIDI FOOT CONTROLLER FCB1010.
MIDI FOOT CONTROLLER FCB1010 2 This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosurevoltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature.
MIDI FOOT CONTROLLER FCB1010 3 F C B 1010 MIDI FOOT CONTROLLER Ultra-Flexible MIDI FOOT CONTROLLER with Two Expression Pedals and MIDI Merge Function s 10 banks of presets, each with 10 fully user-edi.
MIDI FOOT CONTROLLER FCB1010 4 FOREWORD Dear Customer, welcome to the team of BEHRINGER users, and thank you very much for expressing your confi- dence in us by pur- chasing the FCB1010 .
MIDI FOOT CONTROLLER FCB1010 5 1. INTRODUCTION Congratulations! With the BEHRINGER MIDI FOOT CONTROLLER FCB1010 you purchased an ultra-flexible controller unit for a wide range of applications, whethe.
MIDI FOOT CONTROLLER FCB1010 6 2. PROGRAMMING THE FCB1010 1.3.2 Rear panel Fig. 1.2: Rear panel connectors FUSE HOLDER / VOLTAGE SELECTOR. Please make sure that your local voltage matches the voltage indicated on the unit, before you attempt to connect and operate the FCB1010.
MIDI FOOT CONTROLLER FCB1010 7 2. PROGRAMMING THE FCB1010 Fig. 2.2: PRESET selection with DIRECT SELECT enabled As this example shows, the DIRECT SELECT feature gives you a faster access to BANKS and PRESETS than without this function. Which option to use is entirely up to you.
MIDI FOOT CONTROLLER FCB1010 8 1 SW I T CH 1 Determines if UP k ey toggles SW I TCH 1 relay while DI RECT SELECT is enabl ed. 2 SW I T CH 2 Determines i f DOW N k ey t oggles SW I TCH 2 relay while DI RECT SELECT is enabl ed. 5 COPY PRESET Enables copying preset s (see c h.
MIDI FOOT CONTROLLER FCB1010 9 s If you have selected EXP A or EXP B , you can now enter the controller number the EXPRESSION PEDAL of your choice is aimed to send values for. Confirm your selection with UP/ENTER and enter the lower value (pedal up). Confirm with UP/ENTER.
MIDI FOOT CONTROLLER FCB1010 10 s Activate the expression pedal you wish to program by keeping the corresponding foot key pressed for a few seconds (foot keys 8 or 9). The foot key LED blinks after you briefly press the foot key yet again. s Confirm with UP/ENTER.
MIDI FOOT CONTROLLER FCB1010 11 2.5 Controller toggle function This function allows you to configure one controller so that it alternately sends two different values, e.g. effect bypass, drive on/off, etc. s In order to enable the controller switch-over function, you need to globally select the same MIDI channel for CNT1 and CNT2 (see chapter 2.
MIDI FOOT CONTROLLER FCB1010 12 Fig. 2.5: Sending a SysEx-Dump 2.7.2 Receiving SysEx dumps To send back FCB1010 data stored on a sequencer/computer before, please follow the instructions below: s Connect the MIDI OUT connector of your sequencer or computer to the MIDI IN connector of the FCB1010 (see fig.
MIDI FOOT CONTROLLER FCB1010 13 s Keep the switches 1 and 3 pressed while powering up the unit. This puts your FCB1010 i nto self-test mode , and all LEDs are being tested. s Please wait until all switch LEDs light up. Then press all the switches, including the UP/ENTER and DOWN/ESCAPE keys, so that all LEDs are turned off.
MIDI FOOT CONTROLLER FCB1010 14 4. MIDIA STANDARD, A REVOLUTION In the early 80s several leading manufacturers of electronic musical instruments developed a common standard, which was soon to revolutionize the entire MI industryboth from a technical and musical point of view.
MIDI FOOT CONTROLLER FCB1010 15 6. SPECIFICATIONS 4.2.4 Running status Since the MIDI standard uses a serial transmission format, i.e. transmits data successively, it was soon found that the transmission rate is too low if the system is exploited to its full capacity.
MIDI FOOT CONTROLLER FCB1010 16 7. WARRANTY The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or transmitted in any form or by any .
Een belangrijk punt na aankoop van elk apparaat Behringer FCB1010 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Behringer FCB1010 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Behringer FCB1010 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Behringer FCB1010 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Behringer FCB1010 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Behringer FCB1010 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Behringer FCB1010 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Behringer FCB1010 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
