Gebruiksaanwijzing /service van het product 8201VS van de fabrikant Wilton
Ga naar pagina of 32
This Manual is Bookmarked Operating Instructions — Parts Manual 14-Inch V ertical Band Saws Models: 8201, 8203, 8201VS and 8203VS WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60123 Part No. 9078171 Ph.: 800-274-6848 Revision C2 04/07 www .wmhtoolgroup.
.
3 T able of Content s Cover Page .................................................................................................. 1 General Specifications ................................................................................. 4 Operating Precautions .
4 Wilton’s 14-inch T radesman V ertical Band Saws are specially designed to effectively cut a variety of materials including wood, plastic, bakelite, com- posites, ferrous and non-ferrous metals. Models 8201 and 8203 are wood and metal cutting band saws.
5 - Always follow instructions in Operating Instruc- tions and Parts Manual when changing acces- sory tools or parts. - Never modify the machine without consulting Wilton Corporation. Y ou - the St ationary Power T ool User - Hold the Key to Safety . Read and follow these simple rules for best results and full benefits from your machine.
6 safe by using padlocks, master switches, or by removing starter keys. Conductor Length A WG (American Wire Gauge) Number 240 V olt Lines 120 V olt Lines 0 - 50 Feet No. 14 No. 14 50 - 100 Feet No. 14 No. 12 Over 100 Feet No. 12 No. 8 Safety Instructions on Sawing Systems B C D 8.
7 Upper blade guide and support assembly ON/OFF switch Optional rip fence Miter slot T able Lower blade guide and support assembly Lower drive wheel Upper blade guide support assembly Blade guard Lowe.
8 6. T ension the belts (refer to Changing Drive Belt Position) . 7. Check gearbox fluid level in sight gauge. If required, add lubricant to bring level halfway up the sight gauge. (T wo containers of Shell S pirax 90 HD gear oil are packed with the saw .
9 Installing Optional Frame Riser NOTE: Refer to the illustrations in the Replacement Parts section for location of the p arts used on the frame riser . 1. Remove the saw blade (refer to Changing Saw Blades). 2. Remove the two screws at the top and bottom of the blade guide that holds the blade guide on the frame.
10 Operating Controls ST ART/ST OP Switch The ST ART/ST OP switch (refer to Figure 5) is used to turn on the band saw drive motor . The ST ART switch has a molded guard which prevent inadvertent pressing of the ST AR T pushbutton. The STOP pushbutton is not guarded to allow use as an E-stop in an emergency .
11 Adjustments Adjusting Blade Support/Guide Height The upper blade support and guide mechanism can be adjusted to accomodate the height of the work piece. 1. T o adjust the support, loosen the knob that clamps the support rod, then move the support up or down in its holder .
12 breaker in the branch circuit. 2. Move the upper blade guide assembly to the very top of its travel. 3. Make sure the blade is straight, and fully tensioned. (A damaged or worn blade may provide a poor reference surface for squaring the table.) 4. Loosen the table lock knobs and hold the table firmly against it s positive leveling stop.
13 1. T urn the main switch to off. 2. Pull the door open on the pulley case. 3. T urn the clutch handle clockwise and push in, to engage the high speed pulley drive. Or , turn the clutch handle clockwise, and pull out, to engage the reduction gearbox drive.
14 10. Install the belts as required (refer to Figure 10). 1 1. Release the weight of motor so the motor pivots downward. The weight of the motor will provide adequate belt tension. 12. The weight of the motor should provide sufficient tension so the the middle of the small drive belt is displaced approximately the thickness of the belt.
15 9. USING LEA THER GLOVES AND ANSI Z87.1 EYEWEAR TO PROTECT YOURSELF FROM THE CUTTING BLADE, carefully remove the blade from the drive wheels. Remove the blade out of the saw table through the table. 10. Hang the removed blade in a safe place. NOTE: Clean out the interior of the saw with a shop vacuum.
16 Carbide guide block Blade Blade support bearing Guide block set screws Support bearing shaft Guide block support set screw Figure 14. Lower Blade Support Assembly Replacing drive wheel rubber protectors The rubber rings that cover the drive wheels are called protectors.
17 Periodic Maintenance Maintenance Replace blade when teeth are broken Replace blade when bent — or worn — Use a wider blade for more accurate straight cuts Interval Whenever operating saw Whenev.
18 T roubleshooting Fault Excessive blade breakage Premature blade dulling Bad cuts (out-of-square) Bad cuts (rough) Probable cause 1. Material loose in vise. 2. Incorrect speed or feed. 3. T eeth too coarse for material. 4. Incorrect blade tension. 5.
19 1. Blade is binding in the cut. 2. Blade tension too high. 1. Blade guides worn 2. Blade guide bearings not adjusted. 3. Blade guide bearing bracket is loose. 1. Blade tooth pitch too coarse for workpiece. 2. Feed too slow; feed too fast. 3. Workpiece vibrating.
20 Exploded View and Part s Listing – Base – Models 8201, 8203, 8201VS and 8203VS R ef Part. No. Number Description Qt y 1 5513834 Base 1 2 5513835 Door 1 3 5513836 Lock (Ref. Note 1) 1 4 5513837 W asher (Ref. Note 1) 1 5 5513838 Bolt, Pan Head (M4x5) 2 (Ref.
21 Exploded View – Saw Head – Models 8201, 8203, 8201VS, and 8203VS.
22 Re f Part. No. Number Description Qty 1 578251 1 Upper Arm, Frame 1 2 5782521 Bracket, Upper Wheel Sliding 1 3 5782531 Hinge, Upper Wheel Shaf t 1 4 5782541 Pin, Pivot 2 5 5782551 Shaft, Upper Wheel 1 6 5782561 Pin, Roll (4x16) 1 7 5782571 Knob, Blade T rack Adjustment 1 (M8x55) 8 5782581 Nut, Wing (M8x1.
23 Exploded View – Gearbox – Models 8201 and 8203.
24 R ef Part. No. Number Description Qty 1 5783831 Housing Gearbox 1 2 5629151 Bearing (6206ZZ) 1 3 9100441 Bearing (6200ZZ) 3 4 5783851 Bearing (6303ZZ) 1 5 5783861 Plug 2 6 5783871 Seal, Oil (30x7) .
25 Exploded V iew – Gearbox – Models 8201VS and 8203VS.
26 Parts Listing – Gearbox – Models 8201VS and 8203VS R ef Part. No. Number Description Qty 1 5513790 Housing Gearbox 1 2 5513791 Packing 1 3 5783861 Plug 2 4 578391 1 Gauge, Oil Level 1 5 5513794.
27 Parts List – Optional Riser Block – All Models R ef Part. No. Number Description Qt y 1 578451 1 Block, Riser 1 2 5784521 Guard, Blade 1 3 5784531 Hook, Bracket 2 4 5784541 Screw , Self T appin.
28 Parts List – Optional Rip Fence – All Models R ef Part. No. Number Description Qt y 1 578481 1 Rail, Guide 2 2 5784821 Fence, Rip 1 3 5784831 Seat Assembly , Clamp 1 4 5784841 Clamp Rail 1 5 57.
29 Notes:.
.
.
WMH T ool Group 2420 V antage Drive Elgin, IL 60123 Phone: 847-274-6848.
Een belangrijk punt na aankoop van elk apparaat Wilton 8201VS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Wilton 8201VS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Wilton 8201VS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Wilton 8201VS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Wilton 8201VS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Wilton 8201VS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Wilton 8201VS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Wilton 8201VS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
