Gebruiksaanwijzing /service van het product W1099 van de fabrikant Woodstock
Ga naar pagina of 21
COPYRIGHT © BY WOODSTOCK INTERNATIONAL, INC. TX 4-085-998 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. REPRINTED FEBRUARY 1999, PRINTED IN TAIWAN DOVETAIL JIG W1099 OPERATING MANUAL P.
TABLE OF CONTENTS Woodstock Intl., Inc. W1099 I. INTRODUCTION ............................................................................................................................. 2 II. COMMENTARY ..............................................
I. INTRODUCTION - 2 - Woodstock Intl., Inc. W1099 II. COMMENTARY Woodstock International, Inc. is proud to offer the W1099 12" Dovetail Jig. Suitable for pro - duction work or small scale dovetai.
- 3 - Woodstock Intl., Inc. W1099 III. SAFETY RULES FOR ALL TOOLS 1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications and limitations, as well as its particular hazards. 2. KEEP ALL GUARDS IN PLACE and in working order.
IV. UNPACKING - 4 - Woodstock Intl., Inc. W1099 Remove the items packed in the carton. It may be a good idea to save the carton and packing material in case they might be needed in the future. Upon removal of all items from the package, you should have: 1.
- 5 - Woodstock Intl., Inc. W1099 Pin Depth The W1099 is designed to produce half-blind dovetail joints with a router, 7 / 16 " guide bushing, and 14°, 1 / 2 " dovetail router bit. Half-blind dove- tails are very strong and are commonly used in fine drawer construction.
- 6 - Woodstock Intl., Inc. W1099 VIII. ADJUSTMENT LOCATIONS 1. The hand levers clamp your workpiece in place. 2. The fence knobs hold the fence in place. Loosen these knobs to adjust fence position. Router travel is stopped when the router base contacts the fence.
- 7 - Woodstock Intl., Inc. W1099 The side stops serve three purposes: 1) they posi- tion each workpiece square to each other, 2) they offset the two workpieces for proper alignment, and 3) they give lateral support to the workpieces during routing. IMPORTANT: All pieces must be cut perfectly square for the jig to work properly.
- 8 - Woodstock Intl., Inc. W1099 4. Insert a drawer side under the front clamp. This piece will be vertical. Adjust the height so the end of the vertical board overlaps the end of the horizontal board. At this point it is not crucial that the pieces be flush.
- 9 - Woodstock Intl., Inc. W1099 XI. TEMPLATE ADJUSTMENT The template is adjustable from front to back so that the joint will be hidden when the dovetails are complete. Adjustment is made by loosening the two template lock knobs. Do not adjust the screws holding the template.
- 10 - Woodstock Intl., Inc. W1099 The fence controls the depth of the dovetail pins by limiting the distance that the router travels. The router stops when the router base hits the fence. The fence must be adjusted parallel to the edge of the vertical piece just like the template.
- 11 - Woodstock Intl., Inc. W1099 Your router base must accept a guide bushing with a 7 / 16 " outside diameter and an inside diameter large enough to accept a 1 / 4 " shank dovetail bit. Securely mount the guide bushing to your router. Refer to your router’s operating manual for further instructions.
- 12 - Woodstock Intl., Inc. W1099 Figure 13 shows dovetails after cutting. Figure 14 shows a finished drawer and 2 sides ready to be joined. Use care when the router bit exits the workpiece to reduce the risk of tear-out. See section XIV.A. for further instructions.
- 13 - Woodstock Intl., Inc. W1099 B. RABBETED DRAWER FRONTS Drawer fronts that have been rabbeted around the inside edge to create a lip to restrict drawer travel in the closed position require some additional setup. To produce half-blind dovetails on rabbeted draw - er fronts: 1.
- 14 - Woodstock Intl., Inc. W1099 XIV. TROUBLESHOOTING C. INCOMPLETE FIT An incomplete fit occurs when the side piece protrudes from the end of the front or back piece. Figure 17. Cause: The distance between the edge of the side piece and fence is set too narrow.
- 15 - Woodstock Intl., Inc. W1099 XIV. TROUBLESHOOTING E. FIT TOO TIGHT OR TOO LOOSE If you find the fit to be about right in every other aspect, but it is simply a little too tight or too loose, the depth of the router bit is probably mal - adjusted.
XV. WARRANTY - 16 - Woodstock Intl., Inc. W1099 LIMITED WARRANTY Woodstock International, Inc. (Woodstock) war- rants this product against defects in workmanship and materials under normal use and service for a period of one year. This warranty extends to the original purchaser from the date of purchase.
- 17 - Woodstock Intl., Inc. W1099 XVII. PARTS DIAGRAM.
- 18 - Woodstock Intl., Inc. W1099 XVIII. PARTS LIST XIX. TOOL DATA W1099 DOVETAIL JIG Overall Dimensions: Height .........................................................................................................................................
- 19 - Woodstock Intl., Inc. W1099 XX. INDEX A Address ............................................................... 1 Adjustment Locations ......................................... 5 Assembly ........................................................
- 20 - Woodstock Intl., Inc. W1099 NOTES.
Een belangrijk punt na aankoop van elk apparaat Woodstock W1099 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Woodstock W1099 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Woodstock W1099 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Woodstock W1099 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Woodstock W1099 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Woodstock W1099 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Woodstock W1099 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Woodstock W1099 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
