Gebruiksaanwijzing /service van het product KHMS 9010/I van de fabrikant KitchenAid
Ga naar pagina of 20
KHMS 9010/I.
.
Product description and symbols 4 Gas burner functions 4 Practical advice on how to use the burners 5 Injectors table 5 Induction zone functions 6 Positioning the pan supports and Wok support 7 Sizes .
1. Removable pan supports 2. Professional double crown W ok burners 3. 145 mm diameter induction zone 4. Left gas burner control knob 5. Central gas burner control knob 6. Right gas burner control knob 7. Display and touch control panel for the induction zones Gas burner control knob symbols A.
Read these instructions to get the best out of your burners: - Use pans with a diameter the same as the burner (see pan diameter table to the side). - Only use flat bottom pots and pans. - Use the right amount of water for cooking food and use the lid.
This hob is fitted with 2 induction zones that allow you to boil water very quickly , as well as control the temperature with extreme precision, giving you a vast range of cooking options. The induction zone control panel has the following functions. 1.
The time remaining can also be changed by pressing the clock symbol button (4) at any time and using the +/- buttons (3) to alter the time. The light above the display will flash for 10 seconds, then the display will show the amended time remaining. When the programmed time expires a continuous double signal will be heard.
NOTE: If a hood is installed above the hob, read the instructions for fitting the hood where it indicates the correct distances to be complied with. • The cooktop has to be set into a work top between 20 - 40 mm deep.
T o get the best out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose symbol of destination is shown on the product description sheet and hob. • The packaging (plastic bags, expanding polyurethane, etc.
P acking The packaging material is 100% recyclable and is labelled with the recycling symbol that identifies it as a kind of material to be sent to local waste disposal centres. Product This appliance is marked according to the European Directive 2002/96/EC, W aste Electrical and Electronic Equipment (WEEE).
T echnical information for the installer • This product can be built into a 20 to 40 mm deep worktop. • The hob cannot be installed with an oven underneath. Always insert a separator panel under the hob at a distance of no less than 25 mm from the lowest point (electronic control module) on the appliance.
The gas mains system must comply with local regulations. • The paragraph on “national legislation reference” shows the local legislation specific to the country of destination. • Should there be no information regarding your country of interest, ask for further details from the installer .
1. After cleaning the surfaces around the edges, fit the seal provided around the hob. 2. P osition the hob inside the opening according to the sizes indicated in the description sheet. 3. Use the brackets (A) provided to secure the hob, fixing it with the proper screws to adapt it to the thickness.
(See the product description sheet for model) Remove the bottom of the hob, lifting out the installation brackets to change the dual crown wok burner injector . Please contact the Customer Care Centre. REMOVING THE MAIN INJECTOR Remove the injector (F) using a 10mm spanner .
In order to keep your hob in good condition, you must keep it clean, removing any food residue each time you use it. Always disconnect the hob from the electrical power supply and wait until it cools before cleaning.
The hob is not working properly or not working at all. Before calling the Customer Care Centre, see if the problem you are encountering is mentioned in this guide. Contact the Customer Care Centre to replace the power cable. Burners and gas rings 1. The burner doesn’t come on or the flame is uneven.
Before contacting the Customer Care Centre, clarify that you cannot resolve the problem yourself based on the descriptions given in the “T roubleshooting guide”. 1. T urn the apparatus off and restart it to see if the fault is repeated. If after carrying out the above checks, the fault persists, contact your Customer Care Centre.
.
.
5019 719 01020 Printed in Italy n 01/07 GB.
Een belangrijk punt na aankoop van elk apparaat KitchenAid KHMS 9010/I (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen KitchenAid KHMS 9010/I heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens KitchenAid KHMS 9010/I vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding KitchenAid KHMS 9010/I leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over KitchenAid KHMS 9010/I krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van KitchenAid KHMS 9010/I bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de KitchenAid KHMS 9010/I kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met KitchenAid KHMS 9010/I . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
