Gebruiksaanwijzing /service van het product 9175 van de fabrikant Wagner SprayTech
Ga naar pagina of 28
Owner’s Manual Read this manual for complete instructions Table of Contents Safety ................................................................................2-3 Components and Description ........................................4-5 Assembly...
This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury. HAZARD: INJECTION INJURY A high pressure paint stream produced by this equipment can pierce the skin and underlying tissues, leading to serious injury and possible amputation.
3 English Important Safety Information · Read all safety information before operating the equipment. SAVE THESE INSTRUCTIONS. HAZARD: GENERAL Can cause severe injury or property damage. PREVENTION: • Read all instructions and safety precautions before operating equipment.
English 4 Components and Description Components Tools Needed for Assembly The shipping carton for your painting system contains the following: • Suction tube and return tube • Pump cleaning adapte.
5 English Components and Description Oiler (9155, 9175 and 9195 only) Spray hose port (reverse side) Pail bracket Oiler button (9155, 9175 and 9195 only) Pusher stem Suction set filter *Pump cleaning .
English 6 Assembly Do not plug in the power cord until assembly is complete. If you have one of the cart models, follow these assembly instructions. If you have the model 9145 sprayer, skip to item 4, below. 1. Twist the knobs on either side of the handle counterclockwise to unlock the handle.
7 English Before you Begin - This section contains instructions that will be repeated throughout this manual. Locking the Spray Gun Always lock the trigger off when attaching the spray tip or when the spray gun is not in use. GX-05 / GX-07 The gun is locked when the trigger lock is at a 90º angle (perpendicular to the trigger in either direction).
English 8 Preparing the Sprayer All new units are performance-tested at the factory and are shipped with test uid in the uid section to prevent corrosion during shipment and storage. If you have already used your pump, some water or solvent used in cleaning may remain in the uid section.
9 English Preparing the Spray Hose and Spray Gun The spray tip assembly should not be attached to the spray gun when purging the spray hose. Failure to comply could result in an injection injury. 1. Unlock the spray gun and turn the PRIME/SPRAY knob to PRIME.
English 10 Practice / Spraying Technique IMPORTANT: Be sure that the paint hose is free of kinks and clear of objects with sharp cutting edges. 1. Switch the pump ON (l). Turn the PRIME/SPRAY knob to SPRAY. Turn the pressure control dial to maximum pressure (+).
GX-05 / GX-07 GX-08 CLEAN 11 English Spraying Troubleshooting - Unclogging the Spray Tip If the spray pattern becomes distorted or stops completely while the gun is triggered, follow these steps. Do not attempt to unclog or clean the tip with your finger.
English 12 Spraying Troubleshooting - Cleaning the Spray Gun Filter The screen at the bottom of the suction tube may also need cleaning. Check it every time you change spray containers. The lter must be cleaned every time you use your sprayer. When using thicker spray materials, the lter might need to be cleaned more often.
13 English Cleanup Important Cleaning Notes - Read before cleaning • When using latex materials, clean your sprayer and components with water. When using oil-based materials, use mineral spirits.
English 14 Cleanup - Latex materials (continued) 5. Unclip the return tube from the suction tube and place it into the waste container. Turn the PRIME/SPRAY knob to PRIME. 7. Place the original material container next to the waste container. Aim the spray gun into the side of the original material container and hold the trigger.
15 English Cleanup - oil-based materials 1. Lock the gun and remove spray tip assembly. Submerge suction set into a bucket with appropriate cleaning solution. 3. While pulling the gun trigger, turn the pump ON (l), and turn the PRIME/SPRAY knob to SPRAY to purge material from the hose back into the original container.
English 16 Cleaning the Suction Set 1. Lock the gun and turn the pump OFF (O). 3. When suction set is clean, thread the suction tube back into the inlet valve, and replace the return tube onto the return tube tting. Replace clip. 5. Turn the PRIME/SPRAY knob to PRIME.
17 English Cleaning the Spray Gun Components 1. Make sure the pump is switched OFF (O). Make sure the PRIME/SPRAY knob is turned to PRIME. Unplug the sprayer. 3. Remove lter from spray gun (refer to Cleaning the Spray Gun Filter , page 12). 5. Install gun lter tapered-end rst.
English 18 Title Short-Term Storage (up to 16 hours) Follow these steps when using latex materials only. If using materials that are oil-based, follow the Cleanup and Long- Term Storage steps. Shutdown 1. Lock the spray gun off. 2. Turn the PRIME/SPRAY knob to PRIME.
19 English Long-Term Storage Follow these instructions only after all cleanup steps have been performed. If you have a cart model (9155, 9175 or 9195), you can collapse the cart handle for easier storage. 1. Fill a cup or other container with two ounces of separating oil (P/N 0516913, sold separately) and submerge the inlet valve into the oil.
English 20 Cleaning the Inlet Valve Cleaning or servicing the inlet valve may be required if the unit has priming problems. Priming problems may be prevented by properly cleaning the sprayer and following the long-term storage steps. 1. Remove the suction set.
21 English Fluid Section Seal Replacement Instructions Kit Part Number 0512221A (9145 and 9155) Kit Part Number 0516724 (9175 and 9195) Always wear protective eye wear while servicing the pump. Be sure to follow the Pressure Relief Procedure (page 7) when shutting the unit down for any purpose, including servicing or adjusting.
English 22 Title Troubleshooting / Maintenance Problem A. The sprayer does not start. B. The sprayer starts but does not draw in paint when the PRIME/SPRAY knob is set to PRIME. C. The sprayer draws up paint but the pressure drops when the gun is triggered.
67 Title Español Français English 67 Title Parts List • Liste de pièces • Lista de piezas GX-05 Item Article Articulo Part No. Nº de piéce Pieza No.
68 Title Español Français English Parts List • Liste de pièces • Lista de piezas Item Article Articulo Part No. Nº de piéce Pieza No. English Description Français Description Español Descri.
Español Français English 69 Parts List • Liste de pièces • Lista de piezas Item Article Articulo Part No. Nº de piéce Pieza No. English Description Français Description Español Descripción.
70 Title Español Français English Title Parts List • Liste de pièces • Lista de piezas Item Article Articulo Part No. Nº de piéce Pieza No. English Description Français Description Español .
71 Title Español Français English Title Accessories • Accessoires • Accesorios Item Article Articulo English Description Français Description Español Descripción 0516913 Separating oil Huile .
72 Title Español Français English 72 Warranty • Garantié • Garantía LIMITED WARRANTY - AIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material and workmanship for one year from date of purchase.
Een belangrijk punt na aankoop van elk apparaat Wagner SprayTech 9175 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Wagner SprayTech 9175 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Wagner SprayTech 9175 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Wagner SprayTech 9175 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Wagner SprayTech 9175 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Wagner SprayTech 9175 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Wagner SprayTech 9175 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Wagner SprayTech 9175 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
