NL
Wagner SprayTech logo
Officiële handleiding

Wagner SprayTech W 687 E

86 pagina's·10.4 MB·Verfspuit·PDF·ENITJA
Wagner SprayTech W 687 E
Inhoudsopgave 42 secties 1. Explanation of symbols used · 2. General Safety Instructions · 1. Safety at the workplace · 2. Electrical Safety · … TonenVerbergen
Page 1 of the Wagner SprayTech W 687 E user manual — 1. Safety at the workplace
Pagina 1 · klik om te vergroten
Pagina 1

2 years guarantee 37 CE Declaration of Conformity 75

1. Explanation of symbols used

This symbol indicates a potential danger for you or for the device. Under this symbol you can find important information on how to avoid injuries and damage to the device.

Indicates tips for use and other particularly useful information.

Devices and accessories marked with this symbol are suitable for processing low-viscosity materials such as paints, glazes and wall paints specifically designed for this purpose. If a material bears this logo, it is particularly well suited for use with the relevant device.

Devices and accessories marked with this symbol are suitable for processing high-viscosity materials such as e.g. interior wall paints (dispersions and latex paints). If a material bears this logo, it is particularly well suited for use with the relevant device.

2. General Safety Instructions

1. Safety at the workplace

Keep your workplace clean and well lit. a) Disorder or unlit workplaces may result in accidents.

Never use the tool in hazardous areas that contain flammable liquids, gases b)

or dusts. Power tools generate sparks that can ignite the dust or vapors.

Keep children and other persons away when using the power tool. c) You can lose control of the tool if you are distracted.

Page 2 of the Wagner SprayTech W 687 E user manual — 3. Safety of Persons
Pagina 2 · klik om te vergroten
Pagina 2

2. Electrical Safety

The tool plug must fit into the socket. The plug may not be modified in any a)

form. Do not use adaptor plugs together with protective-earthed tools. Unmodified plugs and suitable sockets reduce the risk of an electric shock.

Avoid physical contact with earthed surfaces such as pipes, heating b)

elements, stoves and refrigerators. The risk through electric shock increases if your body is earthed.

Keep the equipment away from rain and moisture. c) The risk of an electric shock increases if water penetrates electrical equipment.

Do not misuse the mains lead by carrying the tool by the lead, hanging it d)

from the lead or by pulling on the lead to remove the plug. Keep the lead away from heat, oil, sharp edges or moving tool parts. Damaged or twisted leads increase the risk of an electric shock.

If you work outdoors with a power tool, only use extension cables suitable e)

for outdoor use. The use of an extension lead that is suitable for outdoors reduces the risk of an electric shock.

If you cannot avoid using the tool in a damp environment, use a residual f)

current operated circuit-breaker. Using a residual current operated circuit-breaker avoids the risk of electric shock.

3. Safety of Persons

Be attentive. Pay attention to what you are doing and work sensibly with a)

apower tool. Do not use the tool if you are tired or under the influence of drugs, alcohol or medication. Just a moment of inattentiveness while using the tool can lead to serious injuries.

Wear personal safety equipment and always wear safety goggles b) Wearing personal protective equipment, such as dust mask, non-slip safety shoes, safety helm or ear protection, depending on the type of power tools, reduces the risk of injury.

Avoid accidental starting-up. c) Make sure that the electric tool is switched off before you connect it to the power supply, pick it up or carry it. Accidents can occur if you carry the power tool while your finger is on the switch or if you connect the power tool to the power supply which it is on.

Remove setting tools or wrenches before switching on the power tool. d) A tool or wrench that is in a rotating tool part can lead to injuries.

Avoid an unnatural posture. Ensure that you are standing securely and e)

have your balance at all times. This ensures that you can control the tool better in

Page 3 of the Wagner SprayTech W 687 E user manual — 5. Service
Pagina 3 · klik om te vergroten
Pagina 3

unexpected situations.

Wear suitable clothing. Do not wear wide clothing or jewelry. Keep your hair, f)

clothes and gloves away from moving parts. Loose clothing, jewelry or long hair can be caught in moving parts.

This device can be used by children over the age of 8 as well as by people g)

with restricted physical, sensory or mental abilities or who have little experience or knowledge about it, providing they are supervised or instructed on how to use the device safely and what risks are involved. Children may not play with the device. User maintenance and cleaning may not be carried out by children unattended.

4. Usage and treatment of the electric tool

Do not overload the tool. Use the power tool designed for the work that you a)

are doing. You work better and safer in the specified performance range if you use the suitable power tool.

Do not use power tools whose switch is defective. b) A power tool that cannot be switched on or off is dangerous and has to be repaired.

Remove the plug from the socket before carrying out tool settings, changing c)

accessories or putting the tool away. This precautionary measure prevents unintentional starting of the tool.

Store unused power tools so that they are inaccessible to children. Do not d)

let persons use the tool who are not familiar with it or who have not read these instructions. Power tools are dangerous when they are used by inexperienced persons.

Take proper care of your tools. Check whether the moving parts e)

functiontrouble-free and do not jam, whether parts are broken or damaged so that the tool function is impaired. Have damaged parts repaired before using the tool. Many accidents have their origin in power tools that have been maintained badly.

Use the power tool, accessories, insert tools, etc. in accordance with these f)

instructions and in a fashion specified for this special tool type. Take the working conditions and the activity to be carried out into consideration. The use of power tools for purposes other than the intended ones can lead to dangerous situations.

5. Service

Have your tool repaired only by qualified specialist personnel and only with a)

original spare parts. This ensures that the tool safety is maintained.

Page 4 of the Wagner SprayTech W 687 E user manual — 3. Safety Instructions for Spray Guns
Pagina 4 · klik om te vergroten
Pagina 4

If the supply cord is damaged, it must be replaced by the manufacturer or it’s b)

service agent or a similarly qualified person in order to avoid a safety hazard.

3. Safety Instructions for Spray Guns

beings or animals.

Sockets and plugs must be masked. Risk of an electric shock as a consequence of sprayed material entering the socket!

  • Do not use the spray guns to spray flammable substances.
  • The spray guns are not to be cleaned with flammable solvents.
  • Caution against dangers that can arise from the sprayed substance and observe the
  • text and information on the containers or the specifications given by the substance manufacturer. Do not spray any liquid of unknown hazard potential.
  • The device may not be used in workplaces covered by the explosion-protection
  • regulations. To avoid the hazard of explosion when spraying, provide for effective natural or artificial
  • ventilation. There must be no sources of ignition such as, for example, open fires, smoke of lit
  • cigarettes, cigars and tobacco pipes, sparks, glowing wires, hot surfaces, etc. in the vicinity during spraying. Ensure that no solvent vapors are sucked in by the unit. Do not spray onto the unit!
  • The spray gun is not a toy; children must therefore not be allowed to handle it or play
  • with it. Before working on the spray gun remove the power plug from the socket.
  • Cover areas that are
  • not to be sprayed. When working keep in mind that wind, for example, may transport paint mist over great distances and cause damage. The units may only be used with a functional valve.
  • If paints rises in the ventilating hose (Fig. 1, item 18) do not operate the unit further! Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary. Do not lay the spray gun.
  • The device is equipped with a thermal release which disconnects the device in case of
  • overheating. In this case, turn off the device, remove the plug and let the device cool down for at least 1/2 hour. Eliminate the cause of heating, e.g. bent hose, soiled air filter, slots for air intake covered.
Page 5 of the Wagner SprayTech W 687 E user manual — 5. Field of application
Pagina 5 · klik om te vergroten
Pagina 5

With original WAGNER accessories and spare parts, you have the guarantee that all safety regulations are fulfilled.

4. Description/ Scope of delivery

Description/ Scope of delivery (Fig. 1) Air cap 1) Tip 2) Union nut 3) Perfect Spray spray attachment 4) Trigger 5) Material volume regulation 6) Gun handle 7) ON/OFF switch 8) Carry handle 9) Air volume control 10) Air hose 11) Power cable 12) Cover of air filter compartment 13) Air filter 14) Gun holder 15) Container (800 ml) 16) Valve 17) Ventilating hose 18) Carrying belt 19) WallPerfect I-Spray spray attachment 20) Stirring rod 21) Feed hopper (2 pcs.) 22) Replacement nozzle seal (3 pcs.)* 23) Practice poster 24) Operatimg instructions 25) Lubricating grease (without illustration)* 26)

* This is inside the container: remove it before starting operations!

5. Field of application

Many different coating substances can be processed with the W687 E. A different spray attachment must be used, depending on the coating substance:

Wagner SprayTech W 687 E — 5. Field of application diagram (page 5)
Afb. 1 · 5. Field of application

Low-viscosity coating substances: Water- and solvent-based paints, finishes, primers, 2-component paints, clear finishes, automotive finishes, staining sealers and wood sealer-preservatives. All coating materials with the red Perfect Spray logo

Interior wall paint (dispersions and latex paint) All coating materials with the green Perfect Spray logo

Page 6 of the Wagner SprayTech W 687 E user manual — 9.  Preparation of the Coating Material
Pagina 6 · klik om te vergroten
Pagina 6

6. Coating Materials Suitable for Use

Interior wall paint (dispersions and latex paint) Water- and solvent-based paints, finishes, primers, 2-component paints, clear finishes, automotive finishes, staining sealers and wood sealer-preservatives.

7. Coating Materials Not Suitable for Use

Materials that contain highly abrasive components, facade paint, caustic solutions and acidic coating substances. Flammable materials.

8. Preparation of the workplace (for interior wall paint)

Sockets and plugs must be masked. Risk of an electric shock as a consequence of sprayed material entering the socket! Mask all the areas and objects that are not to be spray painted, or remove them from the work area. No liability is assumed for damage due to overspray. Silicate paint corrodes glass and ceramic surfaces upon contact! All such surfaces must therefore be completely covered.

Pay attention to the quality of the adhesive tape used. Do not use excessively strong adhesive tape on wallpaper and painted surfaces, in order to avoid damaging these surfaces when removing the tape. Remove adhesive tape slowly and evenly; do not use jerky movements. Do not leave adhesive tape on surfaces any longer than necessary, in order to minimise the possibility of residues when removing. Also observe the adhesive tape manufacturer's instructions.

9. Preparation of the Coating Material

Mix the material well in the original container. When using interior wall paint, an • agitator is recommended.

W 687 has been developed for use with all conventional paints in their undiluted form. If the surface is smooth and the paint you are using is very thick and gel-like, dilute it by 10%. Dilution can be necessary if the atomisation is coarse or if the flow rate is too low even at the maximum setting. Detailed information about the various materials and the maximum permitted dilution can be found on the manufacturers' technical data sheets (e.g. available on the Internet). i

Spray material that is at least at room temperature provides a better spray result.

Page 7 of the Wagner SprayTech W 687 E user manual — 11.  Selecting the Spray Setting (Perfect Spray spray attachment)
Pagina 7 · klik om te vergroten
Pagina 7

10. Start-up

Before connecting to the mains supply, be sure that the supply voltage is identical with the value given on the rating plate. Put the machine down only on a level, clean surface. Otherwise, the gun may suck in dust, etc.

Attach the carrying strap to the unit. (Fig. 2) 1. Unscrew the container from the spray gun. 2. Aligning suction tube. (Fig. 3) 3. If the suction tube is positioned correctly, the container contents can be sprayed without almost any residue. When spraying horizontal surfaces, turn suction tube forward. (Fig. 3 A) When spraying objects overhead, turn suction tube back. (Fig. 3 B) i

For easier coating of ceilings and lying objects, we recommend the 60 cm HVLP handle extension. (Order no. 2307 678)

Set the container on a sheet of paper, pour in the prepared coating material and screw 4. the container tightly onto the spray gun. Connect the front part with the rear part of the gun. (Fig. 5) 5. Mount the air hose (Fig. 4, A + B). Insert the air hose firmly into the connection of the 6. unit and the gun handle. The position of the hose is not relevant. Sling on the carrying strap with the unit. 7. Press the ON/OFF switch at the device. 8. i

Wagner SprayTech W 687 E — 10. Start-up diagram (page 7)
Afb. 2 · 10. Start-up

The enclosed practice poster is ideal for familiarising yourself with operation of the spray gun. After trying out the first spray coatings, it makes sense to test it further on cardboard or a similar surface in order to find out the right flow rate of paint and air for the best spray pattern. Detailed information about these settings can be found in chapter 11- 14.

11. Selecting the Spray Setting (Perfect Spray spray attachment)

WARNING! Danger of injury! Never pull the trigger guard while adjusting the air cap. With the union nut (fig. 6, 1) slightly unscrewed, turn the air cap (2) to the desired spraysetting position (arrow). Then tighten the union nut. Fig. 7 A = horizontal flat jet for horizontal surfaces Fig. 7 B = vertical flat jet for vertical surfaces Fig. 7 C = circular jet for corners, edges and hard-to-reach surfaces

Page 8 of the Wagner SprayTech W 687 E user manual — 15.  Spray Technique
Pagina 8 · klik om te vergroten
Pagina 8
Wagner SprayTech W 687 E — 12.  Selecting the Spray Setting (WallPerfect I-Spray spray attachment) diagram (page 8)
Afb. 3 · 12. Selecting the Spray Setting (WallPerfect I-Spr…

12. Selecting the Spray Setting (WallPerfect I-Spray spray attachment)

2 different spray jet shapes can be set by turning the adjustment ring (fig. 8, 1)

Fig. 9 A = vertical flat jet for horizontal surfaces

Fig. 9 B = horizontal flat jet for vertical surfaces

13. Adjusting the Material Volume (Fig. 10)

Set the material volume by turning the regulator on the trigger guard of the spray gun. - turn to the left lower material volume + turn to the right higher material volume

14. Setting the Amount of Air (Fig. 11)

Depending on the viscosity of the material to be sprayed and the finish of the object to be coated, it may be advisable to vary the amount of air. Very low viscosity materials, such as watery glazes do not have to be atomised with the maximum amount of air. In this case it is advisable to reduce the amount of air and thus minimize the spray vapour. This also applies for the use of the low-scale and radiator/detail spray attachment (accessory). - turn to the right lower amount of air + turn to the left higher amount of air

15. Spray Technique

The spray result depends heavily on the smoothness and cleanliness of the surface to be sprayed. Therefore the surface should be carefully prepared and kept free of dust.

  • Cover all surfaces not to be sprayed.
  • Cover screw threads or similar parts of the target object.
Page 9 of the Wagner SprayTech W 687 E user manual — 17.  Taking Out of Operation and Cleaning
Pagina 9 · klik om te vergroten
Pagina 9

The spray movement should come from the arm, not just from the wrist. This ensures that • a uniform distance is maintained between the spray gun and the spray surface during the spray operation. Select a distance of 5 - 15 cm, depending on the desired spray jet width. When you are using interior wall paint, the distance should be about 20-30 cm.

Fig. 12 A/ 12 B: CORRECT Even distance to the object.

  • Fig. 12 B: INCORRECT An uneven distance will result in uneven paint application. Move the spray gun evenly cross-wise or up-and-down, depending on the spray
  • pattern setting. An even movement of the spray gun results in an even surface quality.
  • When coating material builds up on the nozzle and air cap, clean both parts with a
  • solvent or water.

"Cross spray" when using paint with a poor covering capacity or if the surface is highly absorbent (Fig. 13).

Interior wall paint in strong colour shades should be applied at least twice (allow first paint coat to dry first). This will ensure good coverage.

16. Interruption of Work till 4 Hours

  • Turn the machine off.
  • During longer breaks, vent the container by briefly opening and then closing it again.
  • Clean nozzle openings after an interruption in operation.
  • When processing 2-component varnishes, clean the device immediately.

17. Taking Out of Operation and Cleaning

Proper cleaning is the prerequisite for problem-free operation of the paint application device. No warranty claims are accepted in case of improper or no cleaning.

Turn the machine off. Vent the container in case of longer breaks and after the work 1) has been terminated. This can be done by briefly turning open and then closing the container or by pulling the trigger guard and letting the paint into the original paint container. Divide the spray gun. Press the hook (Fig. 5 "click") slightly downwards. Turn the gun 2) front part and gun rear part against each other and take them apart. Unscrew the container. Empty any remaining coating material back into the material 3) tin. Preclean the container and feed tube with a brush. Clean the ventilating bore 4) (Fig. 14, A). Pour solvent or water into the container. Screw the container back on. 5) Do not use flammable materials for cleaning purposes.

Page 10 of the Wagner SprayTech W 687 E user manual — 18. Cleaning the Perfect Spray spray attachment
Pagina 10 · klik om te vergroten
Pagina 10

Assemble the gun again (Fig. 5). 6) Turn on the machine and spray the solvent or water into a container or a cloth. 7) Repeat the above procedure until the solvent or water emerging from the nozzle is 8) clear. Turn off the machine and divide the spray gun. Press the hook (Fig. 5 "click") slightly 9) downwards. Turn the gun front part and gun rear part against each other and take them apart.

18. Cleaning the Perfect Spray spray attachment

Screw of the container and empty it. Pull out the suction tub with container seal. 1) CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects. The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe. Pull the ventilating hose (Fig.15, A) at the top from the gun body. Screw off the valve 2) cover (B). Remove the diaphragm (C). Clean all the parts carefully. Unscrew the union nut and remove the air cap and nozzle. Clean the air cap, nozzle 3) seal and nozzle with a brush and solvent or water (Fig. 16). Clean the outside of the spray gun and container with a cloth soaked in solvent or 4) water. Assemble the parts again (see “Assembly”). 5)

Assembly The unit may only be operated with an integer diaphragm (Fig. 15, C).

Place the diaphragm 1) (Fig. 15 ,C) with the pin facing upwards on the bottom section of the valve. Also see the marking on the gun body. Place on the valve cover (Fig. 15 ,B) and screw it closed. 2) Place the ventilating hose (Fig. 15, A) on the valve cover and on the nipple at the gun 3) body. Slide the nozzle seal (Fig. 17, 1) with the groove (slot) facing forwards into the nozzle 4) (Fig. 17, 2). Put the nozzle onto the gun body and find the correct position by turning it. 5) Put the air cap onto the nozzle and tighten it using the union nut. 6) Place the container seal from below on the suction tube and slide it over the collar, 7) while turning the container seal slightly. Insert the suction tube with container seal in the gun body. 8)

Page 11 of the Wagner SprayTech W 687 E user manual — 18. Cleaning the Perfect Spray spray attachment
Pagina 11 · klik om te vergroten
Pagina 11
Wagner SprayTech W 687 E — 18. Cleaning the Perfect Spray spray attachment diagram (page 11)
Afb. 4 · 18. Cleaning the Perfect Spray spray attachment

Screw of the container and empty it. Pull out the suction tub with container seal. 1) CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects. The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe. Pull the ventilating hose (Fig. 15, A) at the top from the gun body. Screw off the valve 2) cover (B). Remove the diaphragm (C). Clean all the parts carefully. 3) Remove the adjustment ring (fig. 18, 1) carefully from the union nut (2). Unscrew the union nut (fig. 18, 2) and remove the air cap (3) and nozzle (4). Clean the 4) air cap and nozzle with a brush and solvent or water. 5) Clean the outside of the spray gun and container with a cloth soaked in solvent or water. 6) Assemble the parts again (see “Assembly”).

Assembly The unit may only be operated with an integer diaphragm (Fig. 15, C).

Place the diaphragm 1) (Fig. 15, C) with the pin facing upwards on the bottom section of the valve. Also see the marking on the gun body. Place on the valve cover 2) (Fig. 15, B) and screw it closed. Place the ventilating hose 3) (Fig. 15, A) on the valve cover and on the nipple at the gun body. Slide the nozzle seal (Fig. 19, 5) with the groove (slot) facing forwards into the 4) nozzle. Place the nozzle (fig. 19, 4) on to the gun body with the recess facing downwards. 5) Attention: Position of needle must be congruent with the nozzle aperture. (Fig.20) Put the air cap (Fig. 21, 3) onto the nozzle (4) and tighten it using the union nut (2) 6) Position the adjustment ring (fig. 22, 1) on the union nut so that the recesses on the 7) adjustment ring can snap into both horns on the air cap. Place the container seal from below on the suction tube and slide it over the collar, 8) while turning the container seal slightly. Insert the suction tube with container seal in the gun body. 9)

Page 12 of the Wagner SprayTech W 687 E user manual — 21. Spare Parts
Pagina 12 · klik om te vergroten
Pagina 12

20. Maintenance

Replace the air filters depending on soiling. Unplug the power plug. Open the cover of the air filter compartment (Fig. 23, A). Replace both air filters (Fig. 23, B). Close the cover of the air filter compartment. WARNING! Never operate the machine without the air filter; dirt could be sucked in

and interfere with the function of the machine. In order to mount the gun more easily apply lubricating grease (enclosed) liberally to the O-ring at the spray attachment (Fig. 16, A).

21. Spare Parts

Spare Parts List Perfect Spray spray attachment (Fig. 24) Pos. Designation Order No. Perfect Spray spray attachment complete with 800 ml container 2315 861 1 Union nut 0417 319 2 Air cap 2305 129 3 Nozzle 2305 131 4 Nozzle seal 0417 706 5 O-ring of spray attachment 0417 308 6 Ventilating hose, valve cover, diaphragm 2304 027 7 Suction tube 0417 357 8 Container seal 0417 358 9 Container with cover 800 ml 0420 708

Spare Parts List WallPerfect I-Spray spray attachment (Fig. 25) Pos. Designation Order No. WallPerfect spray attachment complete with 1800 ml container 2326 477 1 Spray jet adjustment ring 2328 900 2 Union nut 2328 903 3 Air cap 2328 905 4 Nozzle 2328 908 5 Nozzle seal (2 pcs.) 2304 433 6 O-ring of spray attachment 0417 308 7 Ventilating hose, valve cover, diaphragm 2304 027 8 Suction tube 2328 922 9 Container seal 2328 919 10 Container with cover 1800 ml (only for WallPerfect spray attachment)

2304 025

Page 13 of the Wagner SprayTech W 687 E user manual — 22. Accessories
Pagina 13 · klik om te vergroten
Pagina 13
Wagner SprayTech W 687 E — 22. Accessories diagram (page 13)
Afb. 5 · 22. Accessories

Spare Parts List W687 (Fig. 26) Pos. Designation Order No. 1 Carrying belt 2322 299 2 Gun handle 2303 300 3 Air hose 2303 410 4 Cover of air filter compartment (right and left) 2316 052 5 Air filter (2 pcs.) 2318 585 6 Stirring rod 2304 419 7 Feed hopper (3 pcs.) 2304 028 Lubricating grease 2315 539

22. Accessories

The new CLICK&PAINT SYSTEM with additional spray attachments and accessories offers the right tool for each work.

Accessories (not included in the delivery) Name Order No. HVLP handle extension For easier coating of ceilings and horizontal objects. 2307 678 Container with cover 800 ml Ensures that the paint does not dry out and the solvent does not evaporate.

Brilliant spray attachment incl. 600 ml container Optimised nozzle and air guidance for brilliant paint results

0417 932 Perfect Spray spray attachment incl. 800 ml. conainer For a rapid paint change. For medium- and large-scale objects and furniture.

Small-scale spray attachment incl. 250 ml container For filigree objects, detailed and creative work.

0417 918 Perfect Spray spray attachment incl. 1400 ml container Rapid working at larger objects such as timber houses, garage doors, etc.

0417 917 Detail / Radiator spray attachment incl. 600 ml container For inaccessible places, such as radiators, cupboard corners, recesses etc.

0417 915 WallPerfect I-Spray spray attachment incl. 1300 ml container For processing interior wall paint and high-viscosity coating materials. 2321 896

Further information about the WAGNER range of products for renovating is available under www.wagner-group.com

0413 909 · 0417 914

Page 14 of the Wagner SprayTech W 687 E user manual — Malfunction Cause Remedy
Pagina 14 · klik om te vergroten
Pagina 14

23. Environmental protection

The device and all accessories and packaging have to be recycled in an environmentally friendly manner. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtain information from a specialist retailer. Leftover paint and solvents may not be emptied into drains, the sewage system or disposed of as household rubbish. It has to be disposed of separately as special waste. Please pay special attention to the instructions on the product packaging.

24. Important Note regarding Product Liability!

Due to an EC ordinance in effect since 01.01.1990, the manufacturer is liable for his product only if all parts originate from or were approved by the manufacturer and the devices are assembled and operated correctly. The use of other accessories and spare parts can partially or completely invalidate the liability.

25. Correction of Malfunctions

Malfunction Cause Remedy

  • Nozzle clogged
  • Material volume setting turned too
  • far to the left (-) No pressure build-up in container
  • Container empty
  • Feed tube loose
  • Feed tube clogged
  • Ventilating bore (Fig.14, A) clogged

No coating material emerges from the nozzle

Turn to the right (+) ➞ ➞

Tighten container ➞ ➞

  • Coating material assembly at air
  • cap, nozzle or needle Nozzle loose
  • Nozzle seal worn
  • Nozzle worn

Coating material drips from the nozzle

Union nut tighten ➞ ➞

Show 8 more labels / short text on this page
Clean ➞ ➞ · Refill ➞ ➞ · Insert ➞ ➞ · Clean ➞ ➞ · Clean ➞ ➞ · Clean ➞ ➞ · Change ➞ ➞ · Change ➞ ➞
Page 15 of the Wagner SprayTech W 687 E user manual — Spray material is too cold •
Pagina 15 · klik om te vergroten
Pagina 15

Malfunction Cause Remedy

  • Material volume too large
  • Material volume adjusting screw turned too far to the right (+) Nozzle contaminated
  • Viscosity of coating material too
  • high Too little pressure build-up in
  • container Air filter heavily soiled
  • Amount of air too low

Turn material volume ➞ ➞

adjusting screw to the left (-) Clean ➞ ➞

Dilute further ➞ ➞

Tighten container ➞ ➞

Turn the air volume ➞ ➞

control to the left (+)

  • Spray jet pulsates Coating material in container
  • running out Nozzle seal worn
  • Air filter heavily soiled

Coating material causes "paint tears"

Too much coating material applied. • Turn material volume ➞ ➞

adjusting screw to the right (-)

  • Distance to the object too large
  • Too much coating material applied

Too much fog of coating material (Overspray)

Reduce distance ➞ ➞

Turn material volume ➞ ➞

adjusting screw to the left (-) Turn the air volume ➞ ➞

Amount of air too high •

control to the left (-)

  • Diaphragm soiled
  • Diaphragm defective
  • Clean the diaphragm ➞ ➞

Paint in the ventilating hose

Replace the diaphragm ➞ ➞

Device overheated • Unplug the power ➞ ➞

Device does not function

plug, let the device cool down approx. 30 minutes, do not bend the hose, check the air filter, do not cover the intake slots

Spray material is too cold •

Poor covering capacity on the wall

Heat spray material ➞ ➞ (to maximum 40°C) Cross spray (Fig. 13) ➞ ➞

  • Highly absorbent surface or paint
  • with poor covering capacity Distance too large

Closer to the object ➞ ➞

Show 5 more labels / short text on this page
Atomisation too coarse · Change ➞ ➞ · Refill ➞ ➞ · Replace ➞ ➞ · Change ➞ ➞
Page 16 of the Wagner SprayTech W 687 E user manual — 26. Technical Data
Pagina 16 · klik om te vergroten
Pagina 16

26. Technical Data

Technical Data Max. viscosity: Interior wall paint Varnish paints, glazes, etc.

3600 mPas 170 DIN-s Max. flow rate: Interior wall paint Varnish paints, glazes, etc.

400 ml/min 200 ml/min Power source 230 V ~ , 50 Hz Power consumption 615 W Atomizing output: 160 W Double insulation

Sound pressure level* 77 dB (A); Uncertainty K = 4 dB Sound pressure output* 90 dB (A); Uncertainty K =4 dB

Oscillation level** < 2.5 m/s Air hose length 3.5 m Weight approx. 3.3 kg

* Measured in accordance with EN 50144-2-7:2000 ** Measured in accordance with EN 60745-1

Information about the oscillation level The specified oscillation level has been measured according to a standard test procedure and can be used to compare against electric tools. The oscillation level is also for determining an initial assessment of the vibrational strain. Attention! The vibration emission value can differ from the specified value when the electric tool is actually in use, depending on how the electric tool is being used. It is necessary to specify safety measures to protect the operating personnel. These measures are based on an estimated shutdown during the actual conditions of use (all parts of the operating cycle are taken into consideration here, for example periods when the electric tool is switched off, and, when it is switched on but running without any load).

Page 17 of the Wagner SprayTech W 687 E user manual — 2 years guarantee
Pagina 17 · klik om te vergroten
Pagina 17
Wagner SprayTech W 687 E — 2 years guarantee diagram (page 17)
Afb. 6 · 2 years guarantee

blue = neutral brown = live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifiying the terminals in your plug, proceed as follows: Should the moulded plug have to be replaced, never re-use the defective plug or attempt to plug it into a different 13 A socket. This could result in an electric shock. Should it be necessary to exchange the fuse in the plug only use fuses approved by ASTA in accordance with BS 1362. 5 Amp fuses may be used. To ensure that the fuse and fuse carrier are correctly mounted please observe the provided markings or colour coding in the plug. After changing the fuse, always make sure that the fuse carrier is correctly inserted. With out the fuse carrier, it is not permissible to use the plug. The correct fuses and fuse carriers are available from your local electrical supplies stockist.

2 years guarantee

The guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or free- of-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale.

Page 18 of the Wagner SprayTech W 687 E user manual — PF
Pagina 18 · klik om te vergroten
Pagina 18

CE Konformitätserklärung Wir erklären in alleiniger Verantwortung, dass dieses Produkt den folgenden einschlägigen Bestimmungen entspricht: 2006/42/EG; 2004/108 EG; 2002/95/EG; 2002/96/EG Angewandte harmonisierte Normen: EN 60335-1:2012; EN 50144-2-7:2000; EN 55014-1:2006 + A1:2009 + A2:2011; EN 55014-2:1997 + Corrigendum 1997 + A1:2001 + A2:2008; EN 61000-3-2:2006 + A1:2009 + A2:2009; EN 61000-3-3:2008; EN 62233:2008

PD

CE Declaration of Conformity

P GB

We declare under sole responsibility that this product conforms to the following relevant stipulations: 2006/42/EG; 2004/108 EG; 2002/95/EG; 2002/96/EG Applied harmonised norms: EN 60335-1:2012; EN 50144-2-7:2000; EN 55014-1:2006 + A1:2009 + A2:2011; EN 55014-2:1997 + Corrigendum 1997 + A1:2001 + A2:2008; EN 61000-3-2:2006 + A1:2009 + A2:2009; EN 61000-3-3:2008; EN 62233:2008 CE Déclaration de conformité Nous déclarons sous notre responsabilité que ce produit est en conformité avec les réglementations suivantes: 2006/42/EG; 2004/108 EG; 2002/95/EG; 2002/96/EG Conforme aux normes et documents normalisés: EN 60335-1:2012; EN 50144-2-7:2000; EN 55014-1:2006 + A1:2009 + A2:2011; EN 55014-2:1997 + Corrigendum 1997 + A1:2001 + A2:2008; EN 61000-3-2:2006 + A1:2009 + A2:2009; EN 61000-3-3:2008; EN 62233:2008

PF

CE Conformiteitsverklaring

P NL

Wij verklaren dat dit product voldoet aan de volgende normen: 2006/42/EG; 2004/108 EG; 2002/95/EG; 2002/96/EG En normatieve dokumenten: EN 60335-1:2012; EN 50144-2-7:2000; EN 55014-1:2006 + A1:2009 + A2:2011; EN 55014-2:1997 + Corrigendum 1997 + A1:2001 + A2:2008; EN 61000-3-2:2006 + A1:2009 + A2:2009; EN 61000-3-3:2008; EN 62233:2008

Wagner SprayTech W 687 E — PF diagram (page 18)
Afb. 7

i.V. T. Jeltsch i. V. J. Ulbrich Senior Vice President Vice President Engineering Global Product Strategy & Planning Dokumentationsverantwortlicher Responsible person for documents Responsable de la documentation Documentatieverantwoordelijke

J. Wagner GmbH Otto-Lilienthal-Str. 18 D-88677 Markdorf

Page 19 of the Wagner SprayTech W 687 E user manual — PD
Pagina 19 · klik om te vergroten
Pagina 19
Page 19 of the Wagner SprayTech W 687 E user manual — PD
Page 20 of the Wagner SprayTech W 687 E user manual — PD
Pagina 20 · klik om te vergroten
Pagina 20
Page 20 of the Wagner SprayTech W 687 E user manual — PD
Page 21 of the Wagner SprayTech W 687 E user manual — PD
Pagina 21 · klik om te vergroten
Pagina 21

D J. Wagner GmbH Otto-Lilienthal-Str. 18 D-88677 Markdorf Hotline 0180 5 59 24 637 +49/ (0) 75 44/ 505-1169

CZ e-Coreco s.r.o. Na Roudné 102 301 00 Plzeň +420 734 792 823 +420 227 077 364

B Wagner Spraytech Belgie Veilinglaan 56-58 1861 Meise-Wolvertem +32/2/2 69 46 75 +32/2/2 69 78 45

E J. Wagner Spraytech ibérica S.A. Ctra. N-340, Km 1245,4 08750 Molins de rei (Barcelona) +34/93/6 80 00 28 +34/93/6 68 01 56

F Wagner france S.a.r.l. 12 Avenue des Tropiques Z.A. de Courtaboeuf 91978 les ulis Cedex 0 825 011 111 +33 (0) 1 69 81 72 57

SLO Adresa servisa: GMA elektromehanika d.o.o. Cesta Andreja Bitenca 115, ljubljana 1000/Slovenija +386(1)/583 83 04 +386(1)/518 38 03

DK/S Wagner Spraytech Scandinavia A/S Helgeshøj Allé 28 Dk-2630 tåstrup +45/43 27 18 18 +45/43 43 05 28

H Magyarországi szerviz Hondimpex kft. Kossuth L. u. 48-50 8060 Mór +36(-22)/407 321 +36(-22)/407 852

CH J. Wagner AG Industriestraße 22 9450 Altstätten +41/71/7 57 22 11 +41/71/7 57 23 23

PL Put Wagner Service ul. E. Imieli 14 41-605 Swietochlowice

+48/32/2 45 06 19 +48/32/2 41 42 51

SK Phobos Corporation Spol.r.o Stanicna 6, 92700 Sala Slowakei +421/31/7 70 78 84 +421/31/7 70 22 42

HR Adresa servisael-Me-HO Horvatinčićev put 2 10436 rakov Potok/kroatien / +385(-1)65 86 - 028

NL Wagner Spraytech Benelux B.V. De Heldinnenlaan 200 3543 MB utrecht +31/30/2 41 41 55 +31/30/2 41 17 87

AUS Wagner Spraytech Australia Pty. ltd., 14-16 Kevlar Close, Braeside, ViC 3195/Australia +61/3/95 87 20 00 +61/3/95 80 91 20

GB Wagner Spraytech (uk) ltd. The Coach House 2 Main Road Middleton Cheney OX17 2nD

www.wagner-group.com

01295 714200 01295 710100

Irrtümer und Änderungen vorbehalten. Not responsible for errors and changes. Sous réserves d’erreurs et de modifications.

Part. No. 2329194 11/2012_RS © Copyright by J.Wagner GmbH

Fouten en wijzigingen voorbehouden.

Bronnen

Referenties en links

Pagina's waarnaar wordt verwezen in deze handleiding — fabrikant, ondersteuning en downloads.

Probleemoplossing

Probleemoplossing

Veelvoorkomende problemen, mogelijke oorzaken en oplossingen.

ProbleemMogelijke oorzaakOplossing
No coating material emerges from the nozzle• Nozzle clogged • Material volume setting turned too far to the left (-) • No pressure build-up in container • Container empty • Feed tube loose • Feed tube clogged • Ventilating bore (Fig.14, A) clogged➞Clean ➞Turn to the right (+) ➞Tighten container ➞Refill ➞Insert ➞Clean ➞Clean p.14
Coating material drips from the nozzle• Coating material assembly at air cap, nozzle or needle • Nozzle loose • Nozzle seal worn • Nozzle worn➞Clean ➞Union nut tighten ➞Change ➞Change p.14
Atomisation too coarse• Material volume too large Material volume adjusting screw turned too far to the right (+) • Nozzle contaminated • Viscosity of coating material too high • Too little pressure build-up in container • Air filter heavily soiled • Amount of air too low➞Turn material volume adjusting screw to the left (-) ➞Clean ➞Dilute further ➞Tighten container ➞Change ➞Turn the air volume control to the left (+) p.15
Spray jet pulsates• Coating material in container running out • Nozzle seal worn • Air filter heavily soiled➞Refill ➞Replace ➞Change p.15
Coating material causes "paint tears"• Too much coating material applied.➞Turn material volume adjusting screw to the right (-) p.15
Too much fog of coating material (Overspray)• Distance to the object too large • Too much coating material applied • Amount of air too high➞Reduce distance ➞Turn material volume adjusting screw to the left (-) ➞Turn the air volume control to the left (-) p.15
Paint in the ventilating hose• Diaphragm soiled • Diaphragm defective➞Clean the diaphragm ➞Replace the diaphragm p.15
Device does not function• Device overheated➞Unplug the power plug, let the device cool down approx. 30 minutes, do not bend the hose, check the air filter, do not cover the intake slots p.15
Poor covering capacity on the wall• Spray material is too cold • Highly absorbent surface or paint with poor covering capacity • Distance too large➞Heat spray material (to maximum 40°C) ➞Cross spray (Fig. 13) ➞Closer to the object p.15

Vraag stellen over de Wagner SprayTech W 687 E

Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nog geen vragen over de Wagner SprayTech W 687 E

Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.

Origineel document

Wagner SprayTech W 687 E handleiding-pdf

86 pagina's·10.4 MB·Verfspuit·PDF
Klik op een bovenstaande pagina om deze hier te openen
Pagina 1 / …
100%
Pagina's laden…